Rev |
Age |
Author |
Path |
Log message |
Diff |
2429 |
3851 d 1 h |
holgerb |
/tags/V2.04a/ |
2.04a (12.03.2014 after public betatest 2.03)
- No support for FC 1.x
- Bugfix: set ChannelYaw to zero in case of RC lost
- Bugfix: Max 6 cells in lipo-detection instead of 7
- Bugfix: Compass-Calibration: At the second compass calibration, the Calibration started in step 2 and not in step 1
- increase the allowed band for Auto-Middle-Point of the AltitudeStick to 70-175
- Dodeca: reduced I2C Packet length to 8
- Auto-ComingHome at Undervoltage
- Voltage measurement was 3% too high
- allowed band for ACC-Z increased to: 652 - 717
- send 'K' command only if JustMK3MagConnected
- Redundant operation supported
- Loading Waypoints from SD-Card:
- menu by HoTT and Jeti added
- Show the name of the WP-List
- do not load points if no stafix
- Version for FC 2.0 with ATMEGA644
Not Supported in FC 2.0:
- ACC-Upgrade for better ACC-Altitude control
- Hott
- Jeti-EX
- Auto-Start & Landing
- WP-List Name |
|
2415 |
3878 d 1 h |
ingob |
/tags/ |
V2.00a is not compatible to FC V2.5 ! |
|
2405 |
3926 d 0 h |
holgerb |
/tags/V2.02b/ |
2.02a
- code too big for MEGA644 -> only ATMEGA1284 supported
- Jeti:GPS-Koordinate
- Don't accept Reset-Command if Motor running
- 'Idle' Bit in Output-Mask
- Option: DisableServoNick
- Bugfix Maximum Altitude -> New: SpeakHoTT Errormessage = "MaximumAltitude" and VarioCharacter goes to '='
- New Error code 32 "ERR:BL Selftest"
- prepared for current measurements up to 75A per ESC
- reduced speed of capacity-calculation() from 10ms to 50ms - that should be fast enough
- Timing correction for NC-Data (41Hz)
- Autolanding if undervoltage
- Compass offset angle
- 0.2V hysteresis in undervoltage warning
- Fixed: Bug in LED-Output
- Autolanding per default at 3,1V
2.02b
- Bugfix: Data reading for Dodecas (12 motors) |
|
2403 |
3932 d 23 h |
holgerb |
/tags/V2.02a/ |
2.02a
- code too big for MEGA644 -> only ATMEGA1284 supported
- Jeti:GPS-Koordinate
- Don't accept Reset-Command if Motor running
- 'Idle' Bit in Output-Mask
- Option: DisableServoNick
- Bugfix Maximum Altitude -> New: SpeakHoTT Errormessage = "MaximumAltitude" and VarioCharacter goes to '='
- New Error code 32 "ERR:BL Selftest"
- prepared for current measurements up to 75A per ESC
- reduced speed of capacity-calculation() from 10ms to 50ms - that should be fast enough
- Timing correction for NC-Data (41Hz)
- Autolanding if undervoltage
- Compass offset angle
- 0.2V hysteresis in undervoltage warning
- Fixed: Bug in LED-Output
- Autolanding per default at 3,1V |
|
2399 |
3942 d 23 h |
ingob |
/tags/V2.00a/ |
|
|
2398 |
3943 d 1 h |
ingob |
/tags/V2.00f/ |
|
|
2397 |
3943 d 1 h |
ingob |
/tags/V2.00f/Hex-Files/ |
|
|
2396 |
3943 d 1 h |
holgerb |
/tags/V2.00f/ |
2.00f (Version for FC2.5 and older)
- bugfix: 41Hz timing communication FC-NC |
|
2395 |
3943 d 1 h |
holgerb |
/tags/ |
2.00f (Version for FC2.5 and older)
- bugfix: 41Hz timing communication FC-NC |
|
2393 |
3943 d 1 h |
holgerb |
/tags/V2.00f/ |
2.00f (Version for FC2.5 and older)
- bugfix: 41Hz timing communication FC-NC |
|
2359 |
4072 d 23 h |
holgerb |
/tags/V2.00a/ |
2.00a (after public Beta test 0.91)
- show SW-Version in Hot Display
- GPS-Parameter changed (P = 90->100; I = 90->90; D = 90->120; A = 40)
- Move NICK/Roll Sticks for switching on / off
- Move the Stick > 100 instead > 75 for switch on / off
- Failsafe active if ACC-Upgarde
- AltitudeMode, GPS_Mode & Carefree_Mode are now direct channels instead of Poti-Values (NaviGpsModeChannel,CareFreeChannel,HoeheChannel)
- NC-SPI communication from 25Hz to 41Hz
- MotorTemperature and GPS-Mode-Switch more often to NC
- Auto-Start/Landing
- JetiEX: Name set to 'MK'
- if(CareFree) Parameter_AchsKopplung1 += 30; removed
- StickNeutral setting per default 127
- UART-Buffer increased from 175 to 220 Bytes
- show name of active parameter set in the HoTT/Jeti display
- fixed in 0.91L: if "ServoRelative" is used, it coud happen that the servo moves a wide range in the first second after the first calibration
- Servo3-5 Limit to 24-255
- no. of channels increased from 12 to 16
// 0 -> frei bzw. ACT rssi (or zero if unsigned)
// 1 - 16 -> 1-16
// 17 - 28 -> 12 Serial channels
// 29 -> WP-Event kanal
// 30 Fix -> -127
// 31 Fix -> 0
// 32 Fix -> 128 |
|
2358 |
4072 d 23 h |
holgerb |
/tags/V2.00a/ |
Show Settings name |
|
2357 |
4072 d 23 h |
holgerb |
/tags/V2.00a/Hex-Files/ |
2.00a (after public Beta test 0.91)
- show SW-Version in Hot Display
- GPS-Parameter changed (P = 90->100; I = 90->90; D = 90->120; A = 40)
- Move NICK/Roll Sticks for switching on / off
- Move the Stick > 100 instead > 75 for switch on / off
- Failsafe active if ACC-Upgarde
- AltitudeMode, GPS_Mode & Carefree_Mode are now direct channels instead of Poti-Values (NaviGpsModeChannel,CareFreeChannel,HoeheChannel)
- NC-SPI communication from 25Hz to 41Hz
- MotorTemperature and GPS-Mode-Switch more often to NC
- Auto-Start/Landing
- JetiEX: Name set to 'MK'
- if(CareFree) Parameter_AchsKopplung1 += 30; removed
- StickNeutral setting per default 127
- UART-Buffer increased from 175 to 220 Bytes
- show name of active parameter set in the HoTT/Jeti display
- fixed in 0.91L: if "ServoRelative" is used, it coud happen that the servo moves a wide range in the first second after the first calibration
- Servo3-5 Limit to 24-255
- no. of channels increased from 12 to 16
// 0 -> frei bzw. ACT rssi (or zero if unsigned)
// 1 - 16 -> 1-16
// 17 - 28 -> 12 Serial channels
// 29 -> WP-Event kanal
// 30 Fix -> -127
// 31 Fix -> 0
// 32 Fix -> 128 |
|
2356 |
4072 d 23 h |
holgerb |
/tags/V2.00a/Hex-Files/ |
2.00a (after public Beta test 0.91)
- show SW-Version in Hot Display
- GPS-Parameter changed (P = 90->100; I = 90->90; D = 90->120; A = 40)
- Move NICK/Roll Sticks for switching on / off
- Move the Stick > 100 instead > 75 for switch on / off
- Failsafe active if ACC-Upgarde
- AltitudeMode, GPS_Mode & Carefree_Mode are now direct channels instead of Poti-Values (NaviGpsModeChannel,CareFreeChannel,HoeheChannel)
- NC-SPI communication from 25Hz to 41Hz
- MotorTemperature and GPS-Mode-Switch more often to NC
- Auto-Start/Landing
- JetiEX: Name set to 'MK'
- if(CareFree) Parameter_AchsKopplung1 += 30; removed
- StickNeutral setting per default 127
- UART-Buffer increased from 175 to 220 Bytes
- show name of active parameter set in the HoTT/Jeti display
- fixed in 0.91L: if "ServoRelative" is used, it coud happen that the servo moves a wide range in the first second after the first calibration
- Servo3-5 Limit to 24-255
- no. of channels increased from 12 to 16
// 0 -> frei bzw. ACT rssi (or zero if unsigned)
// 1 - 16 -> 1-16
// 17 - 28 -> 12 Serial channels
// 29 -> WP-Event kanal
// 30 Fix -> -127
// 31 Fix -> 0
// 32 Fix -> 128 |
|
2354 |
4073 d 0 h |
holgerb |
/tags/V2.00a/ |
2.00a (after public Beta test 0.91)
- GPS-Parameter changed (P = 90->100; I = 90->90; D = 90->120; A = 40)
- Move NICK/Roll Sticks for switching on / off
- Move the Stick > 100 instead > 75 for switch on / off
- Failsafe active if ACC-Upgarde
- AltitudeMode, GPS_Mode & Carefree_Mode are now direct channels instead of Poti-Values (NaviGpsModeChannel,CareFreeChannel,HoeheChannel)
- NC-SPI communication from 25Hz to 41Hz
- MotorTemperature and GPS-Mode-Switch more often to NC
- Auto-Start/Landing
- JetiEX: Name set to 'MK'
- if(CareFree) Parameter_AchsKopplung1 += 30; removed
- StickNeutral setting per default 127
- UART-Buffer increased from 175 to 220 Bytes
- show name of active parameter set in the HoTT/Jeti display
- fixed in 0.91L: if "ServoRelative" is used, it coud happen that the servo moves a wide range in the first second after the first calibration
- Servo3-5 Limit to 24-255
- no. of channels increased from 12 to 16
// 0 -> frei bzw. ACT rssi (or zero if unsigned)
// 1 - 16 -> 1-16
// 17 - 28 -> 12 Serial channels
// 29 -> WP-Event kanal
// 30 Fix -> -127
// 31 Fix -> 0
// 32 Fix -> 128 |
|
2351 |
4105 d 0 h |
holgerb |
/tags/V0.91L/ |
0.91 (public Beta)
- GPS-Parameter changed (P = 90->100; I = 90->90; D = 90->120; A = 40)
- Move NICK/Roll Sticks for switching on / off
- Move the Stick > 100 instead > 75 for switch on / off
- Failsafe active if ACC-Upgrade
- AltitudeMode, GPS_Mode & Carefree_Mode are now direct channels instead of Poti-Values (NaviGpsModeChannel,CareFreeChannel,HoeheChannel)
- NC-SPI communication from 25Hz to 41Hz
- MotorTemperature and GPS-Mode-Switch more often to NC
- Auto-Start/Landing
- JetiEX: Name set to 'MK'
- if(CareFree) Parameter_AchsKopplung1 += 30; removed
- StickNeutral setting per default 127
- UART-Buffer increased from 175 to 220 Bytes
- show name of active parameter set in the HoTT/Jeti display
- fixed in 0.91L: if "ServoRelative" is used, it could happen that the servo moves a wide range in the first second after the first calibration
- Servo3-5 Limit to 24-255
- no. of channels increased from 12 to 16
// 0 -> frei bzw. ACT rssi (or zero if unsigned)
// 1 - 16 -> 1-16
// 17 - 28 -> 12 Serial channels
// 29 -> WP-Event kanal
// 30 Fix -> -127
// 31 Fix -> 0
// 32 Fix -> 128 |
|
2343 |
4129 d 0 h |
ingob |
/tags/ |
|
|
2339 |
4138 d 20 h |
holgerb |
/tags/V0.90j/Hex-Files/ |
0.90j (27.05.2013)
- Changes for better EEPROM-Safety
- variable ActiveParamSet instead of the direct EEPROM-Reading (faster)
- Checking the ACC-Z value in flight and report ACC-Z if out of range
- disable Altitude hold in case of ACC-Z error |
|
2338 |
4138 d 20 h |
holgerb |
/tags/V0.90j/Hex-Files/ |
0.90j (27.05.2013)
- Changes for better EEPROM-Safety
- variable ActiveParamSet instead of the direct EEPROM-Reading (faster)
- Checking the ACC-Z value in flight and report ACC-Z if out of range
- disable Altitude hold in case of ACC-Z error |
|
2335 |
4139 d 21 h |
holgerb |
/tags/V0.90j/ |
0.90j (27.05.2013)
- Changes for better EEPROM-Safety
- variable ActiveParamSet instead of the direct EEPROM-Reading (faster)
- Checking the ACC-Z value in flight and report ACC-Z if out of range
- disable Altitude hold in case of ACC-Z error |
|