Subversion Repositories NaviCtrl

Rev

Go to most recent revision | Show changed files | Directory listing | RSS feed

Filtering Options

Rev Age Author Path Log message Diff
760 /  
759 /  
758 /  
757 /  
756 3121 d 9 h holgerb /tags/V2.14e/Hex-Files/ 2.14e (19.04.2016)
- no altitude limitation if altitude sensor is defective		  
755 3121 d 9 h holgerb /tags/V2.14e/Hex-Files/ 2.14e (19.04.2016)
- no altitude limitation if altitude sensor is defective		  
754 /  
753 3122 d 3 h holgerb /tags/V2.14e/ 2.14e (19.04.2016)
- no altitude limitation if altitude sensor is defective		  
752 /  
751 /  
750 3141 d 5 h holgerb /tags/V2.14d/ 2.14d (31.03.2016)
- There were still problems: When using one MKGPS V3.5 on two redundant NCs, it could happen that the configuration of the GPS failed		  
749 /  
748 /  
747 3165 d 4 h holgerb /tags/V2.14c/ 2.14c (07.03.2017)
- Bugfix: When using one MKGPS V3.5 on two redundant NCs, it could happen that the configuration of the GPS failed		  
746 /  
745 3172 d 1 h holgerb /tags/V2.14b/ 2.14b (29.02.2016)
- comment in the triggerlog: Longitude and Latitude mixed
- bugfix: external compass was not detected correctly on NC2.x		  
744 /  
743 /  
742 /  
741 3186 d 7 h holgerb /tags/V2.14a/ 2.14 (21.10.2015 - 15.02.2016)
- Version for FC3.0 and 2.x
- prepared for Canbus (Master/Slave)
- Menu: Gyro removed and Analog 5-7 added
- Menu: Settings Name in main menu [0]
- internal compass: variable attitude
- SPI:
- Structures changed to 20 Bytes Payload
- huge block transfer implemented (for Parameter set)
- Settingsfile from FC to NC via SPI
- serial communication processed directly by NC:
'b':// submit extern control
'y':// serial Channels
'g':// request for the externalControl
'p':// request for the PPM_In-Daza
- GPX-Logfile: Settingsname in Logfile
- New: FC_STATUS3_CALIBRATION_DONE
- Menu.c: Showing Slave Status data
- Menu:Trigger Input
- Logfile for Camera-Trigger events (only FC3.0)
- GPS-Config: GPS with dual connector supported
- Errors:
40: RC-Voltage
41: Power Supply
42: ACC not calibratetd
- Uart:
- NC reads and processes SerialPoti
- NC reads and processes ExternalControl
- NC sends PPM_In[]
- CRC Checksum in GPX Logfile
- Menu[30] = CamCtrl
- CamCtrlCharacter in Hott-Menu
- CamCtrlCharacter Shows external TriggerCounter
- CamCtrl supported for NC 2.1
- fixed: sometimes "ERR:BL Seftest" after switch on without any reason
- CamCtrlCharacter in OSD Dataframes
- CamCtrl Shoots always one first Photo when switching to Middle Position
- size of the Settings-Data adjusted
- size of HugePacket reduced to 200 Bytes
- descend in failsafe-case starts as soon as the MK is closer than 35m to FS-Point
- Waypoints:
- Bugfix: if the climbing speed is AUTO: do not report "target reached" until the altitude is reached
- rise on first Waypoint before moving position -> max.20m		  

←Prev12Next→

Show All