Subversion Repositories FlightCtrl

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Copyright (c) 04.2007 Holger Buss
// + Nur für den privaten Gebrauch
// + www.MikroKopter.com
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Es gilt für das gesamte Projekt (Hardware, Software, Binärfiles, Sourcecode und Dokumentation),
// + dass eine Nutzung (auch auszugsweise) nur für den privaten und nicht-kommerziellen Gebrauch zulässig ist.
// + Sollten direkte oder indirekte kommerzielle Absichten verfolgt werden, ist mit uns (info@mikrokopter.de) Kontakt
// + bzgl. der Nutzungsbedingungen aufzunehmen.
// + Eine kommerzielle Nutzung ist z.B.Verkauf von MikroKoptern, Bestückung und Verkauf von Platinen oder Bausätzen,
// + Verkauf von Luftbildaufnahmen, usw.
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Werden Teile des Quellcodes (mit oder ohne Modifikation) weiterverwendet oder veröffentlicht,
// + unterliegen sie auch diesen Nutzungsbedingungen und diese Nutzungsbedingungen incl. Copyright müssen dann beiliegen
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Sollte die Software (auch auszugesweise) oder sonstige Informationen des MikroKopter-Projekts
// + auf anderen Webseiten oder Medien veröffentlicht werden, muss unsere Webseite "http://www.mikrokopter.de"
// + eindeutig als Ursprung verlinkt und genannt werden
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Keine Gewähr auf Fehlerfreiheit, Vollständigkeit oder Funktion
// + Benutzung auf eigene Gefahr
// + Wir übernehmen keinerlei Haftung für direkte oder indirekte Personen- oder Sachschäden
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Die Portierung der Software (oder Teile davon) auf andere Systeme (ausser der Hardware von www.mikrokopter.de) ist nur
// + mit unserer Zustimmung zulässig
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Die Funktion printf_P() unterliegt ihrer eigenen Lizenz und ist hiervon nicht betroffen
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Redistributions of source code (with or without modifications) must retain the above copyright notice,
// + this list of conditions and the following disclaimer.
// +   * Neither the name of the copyright holders nor the names of contributors may be used to endorse or promote products derived
// +     from this software without specific prior written permission.
// +   * The use of this project (hardware, software, binary files, sources and documentation) is only permittet
// +     for non-commercial use (directly or indirectly)
// +     Commercial use (for excample: selling of MikroKopters, selling of PCBs, assembly, ...) is only permitted
// +     with our written permission
// +   * If sources or documentations are redistributet on other webpages, out webpage (http://www.MikroKopter.de) must be
// +     clearly linked as origin
// +   * porting to systems other than hardware from www.mikrokopter.de is not allowed
// +  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// +  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// +  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
// +  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
// +  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// +  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// +  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// +  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// +  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// +  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// +  POSSIBILITY OF SUCH DAMAGE.
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
#include "main.h"

unsigned char EEPromArray[E2END+1] EEMEM;
unsigned char PlatinenVersion = 10;
unsigned char SendVersionToNavi = 1;
// -- Parametersatz aus EEPROM lesen ---
// number [1..5]
void ReadParameterSet(unsigned char number, unsigned char *buffer, unsigned char length)
{
   if((number > 5)||(number < 1)) number = 3;
   eeprom_read_block(buffer, &EEPromArray[EEPROM_ADR_PARAM_BEGIN + length * (number - 1)], length);
   LED_Init();
}

// -- Parametersatz ins EEPROM schreiben ---
// number [1..5]
void WriteParameterSet(unsigned char number, unsigned char *buffer, unsigned char length)
{
   if(number > 5) number = 5;
   if(number < 1) return;
   eeprom_write_block(buffer, &EEPromArray[EEPROM_ADR_PARAM_BEGIN + length * (number - 1)], length);
   SetActiveParamSetNumber(number);
   LED_Init();
}

unsigned char GetActiveParamSetNumber(void)
{
        unsigned char set;
        set = eeprom_read_byte(&EEPromArray[EEPROM_ADR_ACTIVE_SET]);
        if((set > 5) || (set < 1))
        {
                set = 3;
                SetActiveParamSetNumber(set);                           // diesen Parametersatz als aktuell merken
        }
        return(set);
}


void SetActiveParamSetNumber(unsigned char number)
{
        if(number > 5) number = 5;
        if(number < 1) return;
        eeprom_write_byte(&EEPromArray[EEPROM_ADR_ACTIVE_SET], number);                                 // diesen Parametersatz als aktuell merken
}


void CalMk3Mag(void)
{
 static unsigned char stick = 1;

 if(PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] > -20) stick = 0;
 if((PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] < -70) && !stick)
  {
   stick = 1;
   WinkelOut.CalcState++;
   if(WinkelOut.CalcState > 4)
    {
//     WinkelOut.CalcState = 0; // in Uart.c
     beeptime = 1000;
    }
   else Piep(WinkelOut.CalcState);
  }
  DebugOut.Analog[19] = WinkelOut.CalcState;
}

//############################################################################
//Hauptprogramm
int main (void)
//############################################################################
{
        unsigned int timer;

        //unsigned int timer2 = 0;
    DDRB  = 0x00;
    PORTB = 0x00;
    for(timer = 0; timer < 1000; timer++); // verzögern
    if(PINB & 0x01)
     {
      if(PINB & 0x02) PlatinenVersion = 13;
       else           PlatinenVersion = 11;
     }
    else
     {
      if(PINB & 0x02) PlatinenVersion = 20;
       else           PlatinenVersion = 10;
     }

    DDRC  = 0x81; // SCL
    DDRC  |=0x40; // HEF4017 Reset
    PORTC = 0xff; // Pullup SDA
    DDRB  = 0x1B; // LEDs und Druckoffset
    PORTB = 0x01; // LED_Rot
    DDRD  = 0x3E; // Speaker & TXD & J3 J4 J5
    DDRD  |=0x80; // J7 -> Servo signal
        PORTD = 0x77; // LED


    MCUSR &=~(1<<WDRF);
    WDTCSR |= (1<<WDCE)|(1<<WDE);
    WDTCSR = 0;

    beeptime = 2000;

        StickGier = 0; PPM_in[K_GAS] = 0;StickRoll = 0; StickNick = 0;

    ROT_OFF;

    Timer_Init();
        UART_Init();
    rc_sum_init();
        ADC_Init();
        i2c_init();
        SPI_MasterInit();

        sei();

        printf("\n\rFlightControl\n\rHardware:%d.%d\n\rSoftware:V%d.%d%c ",PlatinenVersion/10,PlatinenVersion%10, VERSION_MAJOR, VERSION_MINOR,VERSION_PATCH + 'a');
        printf("\n\r==============================");

        GRN_ON;


        ReadParameterSet(3, (unsigned char *) &EE_Parameter.Kanalbelegung[0], 9); // read only the first bytes
    // valid Stick-Settings?
    if(eeprom_read_byte(&EEPromArray[EEPROM_ADR_VALID]) == 255 || eeprom_read_byte(&EEPromArray[EEPROM_ADR_VALID]) < EE_DATENREVISION ||
        EE_Parameter.Kanalbelegung[0] > 9 || EE_Parameter.Kanalbelegung[1] > 9 || EE_Parameter.Kanalbelegung[2] > 9 || EE_Parameter.Kanalbelegung[3] > 9)
           {
            printf("\n\rInit. EEPROM: Generating Default-Parameter and Stick-Settings...");
        DefaultStickMapping();
       }
    else if(eeprom_read_byte(&EEPromArray[EEPROM_ADR_VALID]) != EE_DATENREVISION) printf("\n\rInit. EEPROM: Generating Default-Parameter using old Stick Settings");

    if(eeprom_read_byte(&EEPromArray[EEPROM_ADR_VALID]) != EE_DATENREVISION)
        {
          DefaultKonstanten1();
          for (unsigned char i=1;i<6;i++)
      {
       if(i==2) DefaultKonstanten2(); // Kamera
       if(i==3) DefaultKonstanten3(); // Beginner
       if(i>3)  DefaultKonstanten2(); // Kamera
       WriteParameterSet(i, (unsigned char *) &EE_Parameter.Kanalbelegung[0], STRUCT_PARAM_LAENGE);
      }
          SetActiveParamSetNumber(3); // default-Setting
          eeprom_write_byte(&EEPromArray[EEPROM_ADR_VALID], EE_DATENREVISION);
        }

    if(eeprom_read_byte(&EEPromArray[EEPROM_ADR_ACC_NICK]) > 4)
     {
       printf("\n\rACC nicht abgeglichen!");
     }

        ReadParameterSet(GetActiveParamSetNumber(), (unsigned char *) &EE_Parameter.Kanalbelegung[0], STRUCT_PARAM_LAENGE);
    printf("\n\rBenutze Parametersatz %d", GetActiveParamSetNumber());


        if(EE_Parameter.GlobalConfig & CFG_HOEHENREGELUNG)
         {
           printf("\n\rAbgleich Luftdrucksensor..");
           timer = SetDelay(1000);
       SucheLuftruckOffset();
           while (!CheckDelay(timer));
       printf("OK\n\r");
        }

        SetNeutral();

        ROT_OFF;

    beeptime = 2000;
    ExternControl.Digital[0] = 0x55;


        printf("\n\rSteuerung: ");
        if (EE_Parameter.GlobalConfig & CFG_HEADING_HOLD) printf("HeadingHold");
        else printf("Neutral");

        printf("\n\n\r");

    LcdClear();
    I2CTimeout = 5000;
    WinkelOut.Orientation = 1;
        while (1)
        {

                if(UpdateMotor)      // ReglerIntervall
            {
                    UpdateMotor=0;
//PORTD |= 0x08;
            if(WinkelOut.CalcState) CalMk3Mag();
            else MotorRegler();
//PORTD &= ~0x08;
            SendMotorData();
            ROT_OFF;
            if(PcZugriff) PcZugriff--;
             else
              {
                           ExternControl.Config = 0;
               ExternStickNick = 0;
               ExternStickRoll = 0;
               ExternStickGier = 0;
              }
            if(SenderOkay)  SenderOkay--;
            if(!I2CTimeout)
                {
                 I2CTimeout = 5;
                 i2c_reset();
                  if((BeepMuster == 0xffff) && MotorenEin)
                   {
                    beeptime = 10000;
                    BeepMuster = 0x0080;
                   }
                }
            else
                {
                 I2CTimeout--;
                 ROT_OFF;
                }
            if(SIO_DEBUG && (!UpdateMotor || !MotorenEin))
              {
               DatenUebertragung();
               BearbeiteRxDaten();
              }
              else BearbeiteRxDaten();
         if(CheckDelay(timer))
            {
            if(UBat < EE_Parameter.UnterspannungsWarnung)
                {
                  if(BeepMuster == 0xffff)
                   {
                    beeptime = 6000;
                    BeepMuster = 0x0300;
                   }
                }
/*           if(SendVersionToNavi)
              {
               SPI_StartTransmitPacket(SPI_CMD_VERSION);//#
               SendVersionToNavi = 0;
              }
              else  SPI_StartTransmitPacket(SPI_CMD_VALUE);//#
*/
             SPI_StartTransmitPacket();//#

             SendSPI = 4;
                         timer = SetDelay(20);
            }
           //if(UpdateMotor) DebugOut.Analog[26]++;
           LED_Update();
          }
     if(!SendSPI) { SPI_TransmitByte(); }
    }
 return (1);
}