WebSVN - FlightCtrl - Rev 1538 - /branches/V0.76g

/*

Copyright 2008, by Killagreg

This program (files mm3.c and mm3.h) is free software; you can redistribute it and/or modify
it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation;
either version 3 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.

Please note: The original implementation was done by Niklas Nold.
All the other files for the project "Mikrokopter" by H. Buss and I. Busker are under the license (License.txt) published by www.mikrokopter.de
*/
#include <stdlib.h>
#include <avr/io.h>
#include <avr/interrupt.h>
#include <inttypes.h>

#include "mm3.h"
#include "main.h"
#include "mymath.h"
#include "fc.h"
#include "timer0.h"
#include "rc.h"
#include "eeprom.h"
#include "printf_P.h"

// for compatibility reasons gcc3.x <-> gcc4.x
#ifndef SPCR
#define SPCR SPCR0
#endif
#ifndef SPIE
#define SPIE SPIE0
#endif
#ifndef SPE
#define SPE SPE0
#endif
#ifndef DORD
#define DORD DORD0
#endif
#ifndef MSTR
#define MSTR MSTR0
#endif
#ifndef CPOL
#define CPOL CPOL0
#endif
#ifndef CPHA
#define CPHA CPHA0
#endif
#ifndef SPR1
#define SPR1 SPR01
#endif
#ifndef SPR0
#define SPR0 SPR00
#endif

#ifndef SPDR
#define SPDR SPDR0
#endif

#ifndef SPSR
#define SPSR SPSR0
#endif
#ifndef SPIF
#define SPIF SPIF0
#endif
#ifndef WCOL
#define WCOL WCOL0
#endif
#ifndef SPI2X
#define SPI2X SPI2X0
#endif
// -------------------------

#define MAX_AXIS_VALUE 500

typedef struct
{
uint8_t STATE;
uint16_t DRDY;
uint8_t AXIS;
int16_t x_axis;
int16_t y_axis;
int16_t z_axis;
} MM3_working_t;

// MM3 State Machine
#define MM3_STATE_RESET 0
#define MM3_STATE_START_TRANSFER 1
#define MM3_STATE_WAIT_DRDY 2
#define MM3_STATE_DRDY 3
#define MM3_STATE_BYTE2 4

#define MM3_X_AXIS 0x01
#define MM3_Y_AXIS 0x02
#define MM3_Z_AXIS 0x03

#define MM3_PERIOD_32 0x00
#define MM3_PERIOD_64 0x10
#define MM3_PERIOD_128 0x20
#define MM3_PERIOD_256 0x30
#define MM3_PERIOD_512 0x40
#define MM3_PERIOD_1024 0x50
#define MM3_PERIOD_2048 0x60
#define MM3_PERIOD_4096 0x70

#if defined(USE_WALTER_EXT) // walthers board
// Output Pins (J9)PC6->MM3_SS ,(J8)PB2->MM3_RESET
#define MM3_SS_PORT PORTC //J9->MM3_SS
#define MM3_SS_DDR DDRC
#define MM3_SS_PIN PC6
#define MM3_RESET_PORT PORTB //J8->MM3_RESET
#define MM3_RESET_DDR DDRB
#define MM3_RESET_PIN PB2
#elif defined(USE_NICK666) // nick666 version 0.67g
#define MM3_SS_PORT PORTD //J5->MM3_SS
#define MM3_SS_DDR DDRD
#define MM3_SS_PIN PD3
#define MM3_RESET_PORT PORTB //J8->MM3_RESET
#define MM3_RESET_DDR DDRB
#define MM3_RESET_PIN PB2
#else // killagregs board
// Output Pins PC4->MM3_SS ,PC5->MM3_RESET
#define MM3_SS_PORT PORTC
#define MM3_SS_DDR DDRC
#define MM3_SS_PIN PC4
#define MM3_RESET_PORT PORTC
#define MM3_RESET_DDR DDRC
#define MM3_RESET_PIN PC5
#endif

#define MM3_SS_ON MM3_SS_PORT &= ~(1<<MM3_SS_PIN);
#define MM3_SS_OFF MM3_SS_PORT |= (1<<MM3_SS_PIN);
#define MM3_RESET_ON MM3_RESET_PORT |= (1<<MM3_RESET_PIN);
#define MM3_RESET_OFF MM3_RESET_PORT &= ~(1<<MM3_RESET_PIN);

MM3_calib_t MM3_calib;
volatile MM3_working_t MM3;
volatile uint8_t MM3_Timeout = 0;

/*********************************************/
/* Initialize Interface to MM3 Compass */
/*********************************************/
void MM3_Init(void)
{
uint8_t sreg = SREG;

cli();

// Configure Pins for SPI
// set SCK (PB7), MOSI (PB5) as output
DDRB |= (1<<DDB7)|(1<<DDB5);
// set MISO (PB6) as input
DDRB &= ~(1<<DDB6);

// Output Pins MM3_SS ,MM3_RESET
MM3_SS_DDR |= (1<<MM3_SS_PIN);
MM3_RESET_DDR |= (1<<MM3_RESET_PIN);
// set pins permanent to low
MM3_SS_PORT &= ~((1<<MM3_SS_PIN));
MM3_RESET_PORT &= ~((1<<MM3_RESET_PIN));

// Initialize SPI-Interface
// Enable interrupt (SPIE=1)
// Enable SPI bus (SPE=1)
// MSB transmitted first (DORD = 0)
// Master SPI Mode (MSTR=1)
// Clock polarity low when idle (CPOL=0)
// Clock phase sample at leading edge (CPHA=0)
// Clock rate = SYSCLK/128 (SPI2X=0, SPR1=1, SPR0=1) 20MHz/128 = 156.25kHz
SPCR = (1<<SPIE)|(1<<SPE)|(0<<DORD)|(1<<MSTR)|(0<<CPOL)|(0<<CPHA)|(1<<SPR1)|(1<<SPR0);
SPSR &= ~(1<<SPI2X);

// Init Statemachine
MM3.AXIS = MM3_X_AXIS;
MM3.STATE = MM3_STATE_RESET;

// Read calibration from EEprom
MM3_calib.X_off = (int8_t)GetParamByte(PID_MM3_X_OFF);
MM3_calib.Y_off = (int8_t)GetParamByte(PID_MM3_Y_OFF);
MM3_calib.Z_off = (int8_t)GetParamByte(PID_MM3_Z_OFF);
MM3_calib.X_range = (int16_t)GetParamWord(PID_MM3_X_RANGE);
MM3_calib.Y_range = (int16_t)GetParamWord(PID_MM3_Y_RANGE);
MM3_calib.Z_range = (int16_t)GetParamWord(PID_MM3_Z_RANGE);

MM3_Timeout = 0;

SREG = sreg;
}

/*********************************************/
/* Get Data from MM3 */
/*********************************************/
void MM3_Update(void) // called every 102.4 µs by timer 0 ISR
{
switch (MM3.STATE)
{
case MM3_STATE_RESET:
MM3_SS_ON // select slave
MM3_RESET_ON // RESET to High, MM3 Reset
MM3.STATE = MM3_STATE_START_TRANSFER;
return;

case MM3_STATE_START_TRANSFER:
MM3_RESET_OFF // RESET auf Low (was 102.4 µs at high level)
// write to SPDR triggers automatically the transfer MOSI MISO
// MM3 Period, + AXIS code
switch(MM3.AXIS)
{
case MM3_X_AXIS:
SPDR = MM3_PERIOD_256 + MM3_X_AXIS;
break;
case MM3_Y_AXIS:
SPDR = MM3_PERIOD_256 + MM3_Y_AXIS;
break;
case MM3_Z_AXIS:
SPDR = MM3_PERIOD_256 + MM3_Z_AXIS;
break;
default:
MM3.AXIS = MM3_X_AXIS;
MM3.STATE = MM3_STATE_RESET;
return;
}

// DRDY line is not connected, therefore
// wait before reading data back
MM3.DRDY = SetDelay(8); // wait 8ms for data ready
MM3.STATE = MM3_STATE_WAIT_DRDY;
return;

case MM3_STATE_WAIT_DRDY:
if (CheckDelay(MM3.DRDY))
{
// write something into SPDR to trigger data reading
SPDR = 0x00;
MM3.STATE = MM3_STATE_DRDY;
}
return;
}
}

/*********************************************/
/* Interrupt SPI transfer complete */
/*********************************************/
ISR(SPI_STC_vect)
{
static int8_t tmp;
int16_t value;

switch (MM3.STATE)
{
// 1st byte received
case MM3_STATE_DRDY:
tmp = SPDR; // store 1st byte
SPDR = 0x00; // trigger transfer of 2nd byte
MM3.STATE = MM3_STATE_BYTE2;
return;

case MM3_STATE_BYTE2: // 2nd byte received
value = (int16_t)tmp; // combine the 1st and 2nd byte to a word
value <<= 8; // shift 1st byte to MSB-Position
value |= (int16_t)SPDR; // add 2nd byte

if(abs(value) < MAX_AXIS_VALUE) // ignore spikes
{
switch (MM3.AXIS)
{
case MM3_X_AXIS:
MM3.x_axis = value;
MM3.AXIS = MM3_Y_AXIS;
break;
case MM3_Y_AXIS:
MM3.y_axis = value;
MM3.AXIS = MM3_Z_AXIS;
break;
case MM3_Z_AXIS:
MM3.z_axis = value;
MM3.AXIS = MM3_X_AXIS;
break;
default:
MM3.AXIS = MM3_X_AXIS;
break;
}
}
MM3_SS_OFF // deselect slave
MM3.STATE = MM3_STATE_RESET;
// Update timeout is called every 102.4 µs.
// It takes 2 cycles to write a measurement data request for one axis and
// at at least 8 ms / 102.4 µs = 79 cycles to read the requested data back.
// I.e. 81 cycles * 102.4 µs = 8.3ms per axis.
// The two function accessing the MM3 Data - MM3_Calibrate() and MM3_Heading() -
// decremtent the MM3_Timeout every 100 ms.
// incrementing the counter by 1 every 8.3 ms is sufficient to avoid a timeout.
if ((MM3.x_axis != MM3.y_axis) || (MM3.x_axis != MM3.z_axis) || (MM3.y_axis != MM3.z_axis))
{ // if all axis measurements give diffrent readings the data should be valid
if(MM3_Timeout < 20) MM3_Timeout++;
}
else // something is very strange here
{
if(MM3_Timeout ) MM3_Timeout--;
}
return;

default:
return;
}
}

/*********************************************/
/* Calibrate Compass */
/*********************************************/
void MM3_Calibrate(void)
{
static int16_t x_min, x_max, y_min, y_max, z_min, z_max;

switch(CompassCalState)
{
case 1: // change to x-y axis
x_min = 10000;
x_max = -10000;
y_min = 10000;
y_max = -10000;
z_min = 10000;
z_max = -10000;
break;
case 2:
// find Min and Max of the X- and Y-Axis
if(MM3.x_axis < x_min) x_min = MM3.x_axis;
if(MM3.x_axis > x_max) x_max = MM3.x_axis;
if(MM3.y_axis < y_min) y_min = MM3.y_axis;
if(MM3.y_axis > y_max) y_max = MM3.y_axis;
break;
case 3:
// change to z-Axis
break;
case 4:
RED_ON; // find Min and Max of the Z-axis
if(MM3.z_axis < z_min) z_min = MM3.z_axis;
if(MM3.z_axis > z_max) z_max = MM3.z_axis;
break;
case 5:
// calc range of all axis
MM3_calib.X_range = (x_max - x_min);
MM3_calib.Y_range = (y_max - y_min);
MM3_calib.Z_range = (z_max - z_min);

// calc offset of all axis
MM3_calib.X_off = (x_max + x_min) / 2;
MM3_calib.Y_off = (y_max + y_min) / 2;
MM3_calib.Z_off = (z_max + z_min) / 2;

// save to EEProm
SetParamByte(PID_MM3_X_OFF, (uint8_t)MM3_calib.X_off);
SetParamByte(PID_MM3_Y_OFF, (uint8_t)MM3_calib.Y_off);
SetParamByte(PID_MM3_Z_OFF, (uint8_t)MM3_calib.Z_off);
SetParamWord(PID_MM3_X_RANGE, (uint16_t)MM3_calib.X_range);
SetParamWord(PID_MM3_Y_RANGE, (uint16_t)MM3_calib.Y_range);
SetParamWord(PID_MM3_Z_RANGE, (uint16_t)MM3_calib.Z_range);

CompassCalState = 0;
break;
default:
CompassCalState = 0;
break;
}
}

/*
void MM3_Calibrate(void)
{
static uint8_t debugcounter = 0;
int16_t x_min = 0, x_max = 0, y_min = 0, y_max = 0, z_min = 0, z_max = 0;
uint8_t measurement = 50, beeper = 0;
uint16_t timer;

GRN_ON;
RED_OFF;

// get maximum and minimum reading of all axis
while (measurement)
{
// reset range markers if yawstick ist leftmost
if(PPM_in[ParamSet.ChannelAssignment[CH_YAW]] > 100)
{
x_min = 0;
x_max = 0;
y_min = 0;
y_max = 0;
z_min = 0;
z_max = 0;
}

if (MM3.x_axis > x_max) x_max = MM3.x_axis;
else if (MM3.x_axis < x_min) x_min = MM3.x_axis;

if (MM3.y_axis > y_max) y_max = MM3.y_axis;
else if (MM3.y_axis < y_min) y_min = MM3.y_axis;

if (MM3.z_axis > z_max) z_max = MM3.z_axis;
else if (MM3.z_axis < z_min) z_min = MM3.z_axis;

if (!beeper)
{
RED_FLASH;
GRN_FLASH;
BeepTime = 50;
beeper = 50;
}
beeper--;
// loop with period of 10 ms / 100 Hz
timer = SetDelay(10);
while(!CheckDelay(timer));

if(debugcounter++ > 30)
{
printf("\n\rXMin:%4d, XMax:%4d, YMin:%4d, YMax:%4d, ZMin:%4d, ZMax:%4d",x_min,x_max,y_min,y_max,z_min,z_max);
debugcounter = 0;
}

// If gas is less than 100, stop calibration with a delay of 0.5 seconds
if (PPM_in[ParamSet.ChannelAssignment[CH_GAS]] < 100) measurement--;
}
// Rage of all axis
MM3_calib.X_range = (x_max - x_min);
MM3_calib.Y_range = (y_max - y_min);
MM3_calib.Z_range = (z_max - z_min);

// Offset of all axis
MM3_calib.X_off = (x_max + x_min) / 2;
MM3_calib.Y_off = (y_max + y_min) / 2;
MM3_calib.Z_off = (z_max + z_min) / 2;

// save to EEProm
SetParamByte(PID_MM3_X_OFF, (uint8_t)MM3_calib.X_off);
SetParamByte(PID_MM3_Y_OFF, (uint8_t)MM3_calib.Y_off);
SetParamByte(PID_MM3_Z_OFF, (uint8_t)MM3_calib.Z_off);
SetParamWord(PID_MM3_X_RANGE, (uint16_t)MM3_calib.X_range);
SetParamWord(PID_MM3_Y_RANGE, (uint16_t)MM3_calib.Y_range);
SetParamWord(PID_MM3_Z_RANGE, (uint16_t)MM3_calib.Z_range);

}
*/

/*********************************************/
/* Calculate north direction (heading) */
/*********************************************/
void MM3_Heading(void)
{
int32_t sin_nick, cos_nick, sin_roll, cos_roll, sin_yaw, cos_yaw;
int32_t Hx, Hy, Hz, Hx_corr, Hy_corr;
int16_t angle;
int16_t heading;

if (MM3_Timeout)
{
// Offset correction and normalization (values of H are +/- 512)
Hx = (((int32_t)(MM3.x_axis - MM3_calib.X_off)) * 1024) / (int32_t)MM3_calib.X_range;
Hy = (((int32_t)(MM3.y_axis - MM3_calib.Y_off)) * 1024) / (int32_t)MM3_calib.Y_range;
Hz = (((int32_t)(MM3.z_axis - MM3_calib.Z_off)) * 1024) / (int32_t)MM3_calib.Z_range;

// Compensate the angle of the MM3-arrow to the head of the MK by a yaw rotation transformation
// assuming the MM3 board is mounted parallel to the frame.
// User Param 4 is used to define the positive angle from the MM3-arrow to the MK heading
// in a top view counter clockwise direction.
// North is in opposite direction of the small arrow on the MM3 board.
// Therefore 180 deg must be added to that angle.
angle = ((int16_t)ParamSet.UserParam4 + 180);
// wrap angle to interval of 0°- 359°
angle += 360;
angle %= 360;
sin_yaw = (int32_t)(c_sin_8192(angle));
cos_yaw = (int32_t)(c_cos_8192(angle));

Hx_corr = Hx;
Hy_corr = Hy;

// rotate
Hx = (Hx_corr * cos_yaw - Hy_corr * sin_yaw) / 8192;
Hy = (Hx_corr * sin_yaw + Hy_corr * cos_yaw) / 8192;

// tilt compensation

// calculate sinus cosinus of nick and tilt angle
angle = (int16_t)(IntegralGyroNick/GYRO_DEG_FACTOR);
sin_nick = (int32_t)(c_sin_8192(angle));
cos_nick = (int32_t)(c_cos_8192(angle));

angle = (int16_t)(IntegralGyroRoll/GYRO_DEG_FACTOR);
sin_roll = (int32_t)(c_sin_8192(angle));
cos_roll = (int32_t)(c_cos_8192(angle));

Hx_corr = Hx * cos_nick;
Hx_corr -= Hz * sin_nick;
Hx_corr /= 8192;

Hy_corr = Hy * cos_roll;
Hy_corr += Hz * sin_roll;
Hy_corr /= 8192;

// calculate Heading
heading = c_atan2(Hy_corr, Hx_corr);

// atan returns angular range from -180 deg to 180 deg in counter clockwise notation
// but the compass course is defined in a range from 0 deg to 360 deg clockwise notation.
if (heading < 0) heading = -heading;
else heading = 360 - heading;
}
else // MM3_Timeout = 0 i.e now new data from external board
{
if(!BeepTime) BeepTime = 100; // make noise to signal the compass problem
heading = -1;
}
// update compass values in fc variables
CompassHeading = heading;
if (CompassHeading < 0) CompassOffCourse = 0;
else CompassOffCourse = ((540 + CompassHeading - CompassCourse) % 360) - 180;
}

Subversion Repositories FlightCtrl

(root)/branches/V0.76g_FC-JN-Receiver/mm3.c @ 1912 - Rev 1538