Subversion Repositories FlightCtrl

Rev

Rev 685 | Blame | Last modification | View Log | RSS feed

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Copyright (c) 04.2007 Holger Buss
// + only for non-profit use
// + www.MikroKopter.com
// + see the File "License.txt" for further Informations
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
#include <stdlib.h>
#include <avr/io.h>
#include <avr/interrupt.h>

#include "analog.h"
#include "main.h"
#include "timer0.h"
#include "fc.h"
#include "printf_P.h"
#include "eeprom.h"

volatile int16_t Current_Nick = 0, Current_Roll = 0, Current_Gier = 0;
volatile int16_t Current_AccX = 0, Current_AccY = 0, Current_AccZ = 0;
volatile int16_t UBat = 100;
volatile int16_t AdValueGyrNick = 0, AdValueGyrRoll = 0, AdValueGyrGier = 0;
volatile int16_t AdValueAccRoll = 0, AdValueAccNick = 0, AdValueAccTop = 0;
volatile uint8_t messanzahl_AccHoch = 0;
volatile int32_t Luftdruck = 32000;
volatile int16_t StartLuftdruck;
volatile uint16_t MessLuftdruck = 1023;
uint8_t DruckOffsetSetting;
volatile int16_t HoeheD = 0;
volatile int16_t tmpLuftdruck;
volatile uint16_t ZaehlMessungen = 0;

/*****************************************************/
/*     Initialize Analog Digital Converter           */
/*****************************************************/
void ADC_Init(void)
{
        uint8_t sreg = SREG;
        // disable all interrupts before reconfiguration
        cli();
        //ADC0 ... ADC7 is connected to PortA pin 0 ... 7
        DDRA = 0x00;
        PORTA = 0x00;
        // Digital Input Disable Register 0
        // Disable digital input buffer for analog adc_channel pins
        DIDR0 = 0xFF;
        // external reference, adjust data to the right
    ADMUX &= ~((1 << REFS1)|(1 << REFS0)|(1 << ADLAR));
    // set muxer to ADC adc_channel 0 (0 to 7 is a valid choice)
    ADMUX = (ADMUX & 0xE0) | 0x00;
    //Set ADC Control and Status Register A
    //Auto Trigger Enable, Prescaler Select Bits to Division Factor 128, i.e. ADC clock = SYSCKL/128 = 156.25 kHz
    ADCSRA = (1<<ADATE)|(1<<ADPS2)|(1<<ADPS1)|(1<<ADPS0);
        //Set ADC Control and Status Register B
        //Trigger Source to Free Running Mode
        ADCSRB &= ~((1 << ADTS2)|(1 << ADTS1)|(1 << ADTS0));
        // Enable AD conversion
        ADC_Enable();
    // restore global interrupt flags
    SREG = sreg;
}

void SucheLuftruckOffset(void)
{
 uint8_t off;
 off = GetParamByte(PID_LAST_OFFSET);
 if(off > 20) off -= 10;
 OCR0A = off;
 Delay_ms_Mess(100);
 if(MessLuftdruck < 850) off = 0;
 for(; off < 250;off++)
  {
  OCR0A = off;
  Delay_ms_Mess(50);
  printf(".");
  if(MessLuftdruck < 900) break;
  }
 SetParamByte(PID_LAST_OFFSET, off);
 DruckOffsetSetting = off;
 Delay_ms_Mess(300);
}


/*****************************************************/
/*     Interrupt Service Routine for ADC             */
/*****************************************************/
ISR(ADC_vect)
{
    static uint8_t adc_channel = 0, state = 0;
    static uint16_t gier1, roll1, nick1;
    static uint8_t messanzahl_Druck = 0;
    // disable further AD conversion
    ADC_Disable();
    // state machine
    switch(state++)
        {
        case 0:
            gier1 = ADC; // get Gyro Gier Voltage 1st sample
            adc_channel = 1; // set next channel to ADC1 = ROLL GYRO
            ZaehlMessungen++; // increment total measurement counter
            break;
        case 1:
            roll1 = ADC; // get Gyro Roll Voltage 1st sample
            adc_channel = 2; // set next channel to ADC2 = NICK GYRO
            break;
        case 2:
            nick1 = ADC; // get Gyro Nick Voltage 1st sample
            adc_channel = 4; // set next channel to ADC4 = UBAT
            break;
        case 3:
                // get actual UBat (Volts*10) is ADC*30V/1024*10 = ADC/3
            UBat = (3 * UBat + ADC / 3) / 4; // low pass filter updates UBat only to 1 quater with actual ADC value
            adc_channel = 6; // set next channel to ADC6 = ACC_Y
            break;
        case 4:
            Current_AccY = NeutralAccY - ADC; // get acceleration in Y direction
            AdValueAccRoll = Current_AccY;
            adc_channel = 7; // set next channel to ADC7 = ACC_X
            break;
        case 5:
            Current_AccX = ADC - NeutralAccX; // get acceleration in X direction
            AdValueAccNick =  Current_AccX;
                    adc_channel = 0; // set next channel to ADC7 = GIER GYRO
            break;
        case 6:
                // average over two samples to create current ADValueGier
            if(BoardRelease == 10)  AdValueGyrGier = (ADC + gier1) / 2;
                        else                                       AdValueGyrGier = ADC + gier1; // gain is 2 times lower on FC 1.1
            adc_channel = 1; // set next channel to ADC7 = ROLL GYRO
            break;
        case 7:
                // average over two samples to create current ADValueRoll
            if(BoardRelease == 10)  AdValueGyrRoll = (ADC + roll1) / 2;
                        else                                       AdValueGyrRoll = ADC + roll1; // gain is 2 times lower on FC 1.1
            adc_channel = 2; // set next channel to ADC2 = NICK GYRO
            break;
        case 8:
                // average over two samples to create current ADValueNick
            if(BoardRelease == 10)  AdValueGyrNick = (ADC + nick1) / 2;
                        else                                       AdValueGyrNick = ADC + nick1; // gain is 2 times lower on FC 1.1
            adc_channel = 5; // set next channel to ADC5 = ACC_Z
            break;
       case 9:
                // get z acceleration
            AdValueAccTop =  (int16_t) ADC - NeutralAccZ; // get plain acceleration in Z direction
            AdValueAccTop += abs(Current_AccY) / 4 + abs(Current_AccX) / 4;
            if(AdValueAccTop > 1)
             {
              if(NeutralAccZ < 800) NeutralAccZ+= 0.02;
             }
             else if(AdValueAccTop < -1)
             {
              if(NeutralAccZ > 600) NeutralAccZ-= 0.02;
             }
            messanzahl_AccHoch = 1;
            Current_AccZ = ADC;
            Mess_Integral_Hoch += AdValueAccTop;      // Integrieren
            Mess_Integral_Hoch -= Mess_Integral_Hoch / 1024; // dämfen
                adc_channel = 3; // set next channel to ADC3 = air pressure
            break;
        case 10:
            tmpLuftdruck += ADC; // sum vadc values
            if(++messanzahl_Druck >= 5) // if 5 values are summerized for averaging
                {
                MessLuftdruck = ADC; // update measured air pressure
                messanzahl_Druck = 0; // reset air pressure measurement counter
                                HoeheD = (int16_t)(StartLuftdruck - tmpLuftdruck - HoehenWert);  // D-Anteil = neuerWert - AlterWert
                Luftdruck = (tmpLuftdruck + 3 * Luftdruck) / 4; // averaging using history
                HoehenWert = StartLuftdruck - Luftdruck;
                tmpLuftdruck = 0;
                }
            adc_channel = 0; // set next channel to ADC0 = GIER GYRO
            state = 0; // reset state
            break;
        default:
            adc_channel = 0;
            state = 0;
            break;
        }
    // set adc muxer to next adc_channel
    ADMUX = (ADMUX & 0xE0) | adc_channel;
    // ??
    if(state != 0) ADC_Enable();
}