WebSVN - FlightCtrl - Diff - Rev 2097 and 2189 - /branches/dongfang_FC

 #include <inttypes.h>
 #include <avr/io.h>
 #include <avr/interrupt.h>
-#include "eeprom.h"
+//#include "eeprom.h"
-#include "analog.h"
+#include "profiler.h"
 #include "controlMixer.h"
+#include "configuration.h"
+#include "analog.h"
 #include "timer0.h"
+#include "debug.h"
+#include "beeper.h"
 #include "output.h"
+#include "commands.h"
+#include "flight.h"
+#include "uart0.h"
+#include "twimaster.h"
 #ifdef USE_MK3MAG
 #include "mk3mag.h"
+#endif
+#define MILLIS_DIVIDER 10
-#endif
+volatile uint32_t jiffiesClock;
-volatile uint32_t globalMillisClock = 0;
+volatile uint32_t millisClock;
-volatile uint8_t  runFlightControl = 0;
+volatile uint8_t  loopJiffiesClock;
-volatile uint16_t beepTime = 0;
-volatile uint16_t beepModulation = BEEP_MODULATION_NONE;
+volatile uint16_t beepTime;
-#ifdef USE_NAVICTRL
+volatile uint16_t beepModulation = BEEP_MODULATION_NONE;
 volatile uint8_t SendSPI = 0;
-#endif
+volatile uint8_t flightControlStatus;
 /*****************************************************
  * Initialize Timer 0
  *****************************************************/
 // timer 0 is used for the PWM generation to control the offset voltage at the air pressure sensor
 // Its overflow interrupt routine is used to generate the beep signal and the flight control motor update rate
 void timer0_init(void) {
-  uint8_t sreg = SREG;
+        uint8_t sreg = SREG;
-  // disable all interrupts before reconfiguration
+        // disable all interrupts before reconfiguration
-  cli();
+        cli();
-  // Configure speaker port as output.
+        // Configure speaker port as output.
-  if (boardRelease == 10) { // Speaker at PD2
+        if (boardRelease == 10) { // Speaker at PD2
-    DDRD |= (1 << DDD2);
+                DDRD |= (1 << DDD2);
-    PORTD &= ~(1 << PORTD2);
+                PORTD &= ~(1 << PORTD2);
-  } else { // Speaker at PC7
+        } else { // Speaker at PC7
-    DDRC |= (1 << DDC7);
+                DDRC |= (1 << DDC7);
-    PORTC &= ~(1 << PORTC7);
+                PORTC &= ~(1 << PORTC7);
-  }
+        }
-  // set PB3 and PB4 as output for the PWM used as offset for the pressure sensor
+        // set PB3 and PB4 as output for the PWM used as offset for the pressure sensor
-  DDRB |= (1 << DDB4) | (1 << DDB3);
+        DDRB |= (1 << DDB4) | (1 << DDB3);
-  PORTB &= ~((1 << PORTB4) | (1 << PORTB3));
+        PORTB &= ~((1 << PORTB4) | (1 << PORTB3));
-  // Timer/Counter 0 Control Register A
+        // Timer/Counter 0 Control Register A
-  // Waveform Generation Mode is Fast PWM (Bits WGM02 = 0, WGM01 = 1, WGM00 = 1)
+        // Waveform Generation Mode is Fast PWM (Bits WGM02 = 0, WGM01 = 1, WGM00 = 1)
-  // Clear OC0A on Compare Match, set OC0A at BOTTOM, noninverting PWM (Bits COM0A1 = 1, COM0A0 = 0)
+        // Clear OC0A on Compare Match, set OC0A at BOTTOM, noninverting PWM (Bits COM0A1 = 1, COM0A0 = 0)
-  // Clear OC0B on Compare Match, set OC0B at BOTTOM, (Bits COM0B1 = 1, COM0B0 = 0)
+        // Clear OC0B on Compare Match, set OC0B at BOTTOM, (Bits COM0B1 = 1, COM0B0 = 0)
-  TCCR0A &= ~((1 << COM0A0) | (1 << COM0B0));
+        TCCR0A &= ~((1 << COM0A0) | (1 << COM0B0));
-  TCCR0A |= (1 << COM0A1) | (1 << COM0B1) | (1 << WGM01) | (1 << WGM00);
+        TCCR0A |= (1 << COM0A1) | (1 << COM0B1) | (1 << WGM01) | (1 << WGM00);
-  // Timer/Counter 0 Control Register B
-  // set clock divider for timer 0 to SYSCLOCK/8 = 20MHz/8 = 2.5MHz
+        // Timer/Counter 0 Control Register B
-  // i.e. the timer increments from 0x00 to 0xFF with an update rate of 2.5 MHz
+        // set clock divider for timer 0 to SYSCLOCK/8 = 20MHz/8 = 2.5MHz
-  // hence the timer overflow interrupt frequency is 2.5 MHz/256 = 9.765 kHz
+        // i.e. the timer increments from 0x00 to 0xFF with an update rate of 2.5 MHz
+        // hence the timer overflow interrupt frequency is 2.5 MHz/256 = 9.765 kHz
-  // divider 8 (Bits CS02 = 0, CS01 = 1, CS00 = 0)
+        // divider 8 (Bits CS02 = 0, CS01 = 1, CS00 = 0)
-  TCCR0B &= ~((1 << FOC0A) | (1 << FOC0B) | (1 << WGM02));
+        TCCR0B &= ~((1 << FOC0A) | (1 << FOC0B) | (1 << WGM02));
-  TCCR0B = (TCCR0B & 0xF8) | (0 << CS02) | (1 << CS01) | (0 << CS00);
+        TCCR0B = (TCCR0B & 0xF8) | (0 << CS02) | (1 << CS01) | (0 << CS00);
-  // initialize the Output Compare Register A & B used for PWM generation on port PB3 & PB4
+        // initialize the Output Compare Register A & B used for PWM generation on port PB3 & PB4
-  OCR0A = 0; // for PB3
+        OCR0A = 0; // for PB3
-  OCR0B = 120; // for PB4
+        OCR0B = 120; // for PB4
-  // init Timer/Counter 0 Register
+        // init Timer/Counter 0 Register
+        TCNT0 = 0;
+        // Timer/Counter 0 Interrupt Mask Register
+        // enable timer overflow interrupt only
+        TIMSK0 &= ~((1 << OCIE0B) | (1 << OCIE0A));
+        TIMSK0 |= (1 << TOIE0);
+        SREG = sreg;
+}
+void runFlightControlTask(void) {
+        if (flightControlStatus != NOT_RUNNING) {
+                // Previous execution not completed! It is dangerous to start another.
+                debugOut.digital[0] |= DEBUG_MAINLOOP_TIMER;
+                return;
+        }
+        debugOut.digital[0] &= ~DEBUG_MAINLOOP_TIMER;
+        controlMixer_periodicTask();
+        commands_handleCommands();
+        flightControlStatus = RUNNING;
+    if (!--I2CTimeout || missingMotor) { // try to reset the i2c if motor is missing or timeout
+         if (!I2CTimeout) {
+             I2C_reset();
+             I2CTimeout = 5;
+         }
+         beepI2CAlarm();
+     }
+        if (analog_controlDataStatus != CONTROL_SENSOR_DATA_READY) {
+                // Analog data should have been ready but is not!!
+                debugOut.digital[1] |= DEBUG_MAINLOOP_TIMER;
+        } else {
+                debugOut.digital[1] &= ~DEBUG_MAINLOOP_TIMER;
+                J4HIGH;
+                analog_sumAttitudeData();
-  TCNT0 = 0;
+                analog_updateControlData();
                 flight_control();
-  // Timer/Counter 0 Interrupt Mask Register
+                output_applyMulticopterMixer();
-  // enable timer overflow interrupt only
+                I2C_start(TWI_STATE_MOTOR_TX);
-  TIMSK0 &= ~((1 << OCIE0B) | (1 << OCIE0A));
+                J4LOW;
-  TIMSK0 |= (1 << TOIE0);
+        }
+        flightControlStatus = NOT_RUNNING;
+}
-  SREG = sreg;
+/*****************************************************/
-}
+/*          Interrupt Routine of Timer 0             */
+/*****************************************************/
+ISR (TIMER0_OVF_vect) { // 9765.625 Hz
+        static uint8_t millisDivider = MILLIS_DIVIDER;
+        static uint8_t controlLoopDivider = CONTROLLOOP_DIVIDER;
+        static uint8_t serialLoopDivider = SERIALLOOP_DIVIDER /2;
+    static uint8_t outputLoopDivider = OUTPUTLOOP_DIVIDER /3;
+        uint8_t beeperOn = 0;
+        jiffiesClock++;
+        loopJiffiesClock++;
+        // profiler_scoreTimerHit();
+        sei();
+        if (!--millisDivider) {
+                millisClock++;
+                millisDivider = MILLIS_DIVIDER;
+        }
+        if (!--controlLoopDivider) {
+            //sei();
-/*****************************************************/
+                controlLoopDivider= CONTROLLOOP_DIVIDER;
+                runFlightControlTask();
+                //cli();
+        }
-/*          Interrupt Routine of Timer 0             */
-/*****************************************************/
+    if (!--serialLoopDivider) {
-ISR(TIMER0_OVF_vect) { // 9765.625 Hz
-  static uint8_t cnt_1ms = 1, cnt = 0;
+        //sei();
-  uint8_t beeperOn = 0;
+        serialLoopDivider= SERIALLOOP_DIVIDER;
+        // Allow serial data transmission if there is still time, or if we are not flying anyway.
-#ifdef USE_NAVICTRL
-  if(SendSPI) SendSPI--; // if SendSPI is 0, the transmit of a byte via SPI bus to and from The Navicontrol is done
+        usart0_transmitTxData();
-#endif
-  if (!cnt--) { // every 10th run (9.765625kHz/10 = 976.5625Hz)
+        usart0_processRxData();
-    cnt = 9;
-    cnt_1ms ^= 1;
-    if (!cnt_1ms) {
+        //cli();
-      if (runFlightControl == 1)
+    }
-        debugOut.digital[1] |= DEBUG_MAINLOOP_TIMER;
-      else
+    if (!--outputLoopDivider) {
-        debugOut.digital[1] &= ~DEBUG_MAINLOOP_TIMER;
+        //sei();
-      runFlightControl = 1; // every 2nd run (976.5625 Hz/2 = 488.28125 Hz)
+        outputLoopDivider= OUTPUTLOOP_DIVIDER;
-    }
+        output_update();
-    globalMillisClock++; // increment millisecond counter
+        //cli();
-  }
+    }
-  // beeper on if duration is not over
+        // beeper on if duration is not over
-  if (beepTime) {
+        if (beepTime) {
-    beepTime--; // decrement BeepTime
+                beepTime--; // decrement BeepTime
-    if (beepTime & beepModulation)
+                if (beepTime & beepModulation)
-      beeperOn = 1;
+                        beeperOn = 1;
-    else
+                else
-      beeperOn = 0;
+                        beeperOn = 0;
-  } else { // beeper off if duration is over
+        } else { // beeper off if duration is over
-    beeperOn = 0;
+                beeperOn = 0;
-    beepModulation = BEEP_MODULATION_NONE;
+                beepModulation = BEEP_MODULATION_NONE;
-  }
+        }
-  if (beeperOn) {
+        if (beeperOn) {
-    // set speaker port to high.
+                // set speaker port to high.
-    if (boardRelease == 10)
+                if (boardRelease == 10)
-      PORTD |= (1 << PORTD2); // Speaker at PD2
+                        PORTD |= (1 << PORTD2); // Speaker at PD2
-    else
+                else
-      PORTC |= (1 << PORTC7); // Speaker at PC7
+                        PORTC |= (1 << PORTC7); // Speaker at PC7
-  } else { // beeper is off
+        } else { // beeper is off
-    // set speaker port to low
+                // set speaker port to low
-    if (boardRelease == 10)
+                if (boardRelease == 10)
-      PORTD &= ~(1 << PORTD2);// Speaker at PD2
+                        PORTD &= ~(1 << PORTD2);// Speaker at PD2
-    else
+                else
-      PORTC &= ~(1 << PORTC7);// Speaker at PC7
+                        PORTC &= ~(1 << PORTC7);// Speaker at PC7
-  }
+        }
 #ifdef USE_MK3MAG
-  // update compass value if this option is enabled in the settings
+        // update compass value if this option is enabled in the settings
-  if (staticParams.bitConfig & CFG_COMPASS_ENABLED) {
+        if (staticParams.bitConfig & CFG_COMPASS_ENABLED) {
-    MK3MAG_periodicTask(); // read out mk3mag pwm
+                MK3MAG_periodicTask(); // read out mk3mag pwm
+        }
 #endif
 }
-// -----------------------------------------------------------------------
-uint16_t setDelay(uint16_t t) {
-  return (globalMillisClock + t - 1);
-}
-// -----------------------------------------------------------------------
-int8_t checkDelay(uint16_t t) {
-  return (((t - globalMillisClock) & 0x8000) >> 8); // check sign bit
-}
-// -----------------------------------------------------------------------
-void delay_ms(uint16_t w) {
-  uint16_t t_stop = setDelay(w);
-  while (!checkDelay(t_stop))
-    ;
-}
 // -----------------------------------------------------------------------
-void delay_ms_with_adc_measurement(uint16_t w, uint8_t stop) {
+uint16_t setDelay(uint16_t t) {

Subversion Repositories FlightCtrl

(root)/branches/dongfang_FC_rewrite/timer0.c @ 2045 - Rev 2097 → 2189