Rev 2427 | Rev 2437 | Go to most recent revision | Show entire file | Ignore whitespace | Details | Blame | Last modification | View Log | RSS feed
Rev 2427 | Rev 2428 | ||
---|---|---|---|
Line 657... | Line 657... | ||
657 | - Autolanding per default at 3,1V |
657 | - Autolanding per default at 3,1V |
Line 658... | Line 658... | ||
658 | 658 | ||
659 | 2.02b |
659 | 2.02b |
Line -... | Line 660... | ||
- | 660 | - Bugfix: Data reading for Dodecas (12 motors) |
|
660 | - Bugfix: Data reading for Dodecas (12 motors) |
661 | |
661 | 662 | 2.04a (12.03.2014 after public betatest 2.03) |
|
- | 663 | - No support for FC 1.x |
|
- | 664 | - Bugfix: set ChannelYaw to zero in case of RC lost |
|
- | 665 | - Bugfix: Max 6 cells in lipo-detection instead of 7 |
|
662 | 2.03a |
666 | - Bugfix: Compass-Calibration: At the second comdass calibration, the Calibration started in step 2 and not in step 1 |
663 | - Bugfix: set ChannelYaw to zero in case of RC lost |
667 | - increase the allowed band for Auto-Middele-Point of the AltitudeStick to 70-175 |
664 | - Dodeca: reduced I2C Packet lenght to 8 |
- | |
665 | - Undervoltage: Auto-ComingHome |
- | |
666 | 668 | - Dodeca: reduced I2C Packet lenght to 8 |
|
667 | 2.03b |
- | |
668 | - Voltage measurement was 3% too high |
- | |
669 | 669 | - Auto-ComingHome at Undervoltage |
|
670 | 2.03c |
- | |
671 | - allowed neutral level of the ACC-Z extended to 717 |
- | |
672 | 670 | - Voltage measurement was 3% too high |
|
673 | 2.03d |
- | |
674 | - send 'K' command only if JustMK3MagConnected |
- | |
675 | - | ||
676 | 2.03e |
- | |
677 | - Bugfix: Max 6 cells in lipo-detection instead of 7 |
- | |
678 | - Bugfix: Autoland and Auto-CH-Voltages were absolut if Settings were read back by the KopterTool |
- | |
679 | 671 | - allowed band for ACC-Z increased to: 652 - 717 |
|
680 | 2.03f |
- | |
681 | - Redundant operation supported |
672 | - send 'K' command only if JustMK3MagConnected |
682 | - Bugfix Compass-Calibration: At the second comdass calibration, the Calibration started in step 2 and not in step 1 |
- | |
683 | - Loading menu by HoTT and Jeti added |
- | |
684 | 673 | - Redundant operation supported |
|
685 | 2.03g |
674 | - Loading Waypoints from SD-Card: |
686 | - loading relative points |
- | |
687 | - Show the name of the WP-List |
- | |
688 | 675 | - menu by HoTT and Jeti added |
|
689 | 2.03i |
- | |
690 | - do not load points if no stafix |
- | |
691 | - | ||
692 | 2.03j |
676 | - Show the name of the WP-List |
693 | - No support for FC 1.x |
677 | - do not load points if no stafix |
694 | - Version for FC 2.0 with ATMEGA644 |
678 | - Version for FC 2.0 with ATMEGA644 |
695 | Not Supported in FC 2.0: |
679 | Not Supported in FC 2.0: |
696 | - ACC-Upgrade for better ACC-Altitude control |
680 | - ACC-Upgrade for better ACC-Altitude control |
697 | - Hott |
681 | - Hott |
698 | - Jeti-EX |
682 | - Jeti-EX |
Line 699... | Line -... | ||
699 | - Auto-Start & Landing |
- | |
700 | - WP-List Name |
- | |
701 | - | ||
Line 702... | Line 683... | ||
702 | 2.03k |
683 | - Auto-Start & Landing |