WebSVN - FlightCtrl - Diff - Rev 942 and 943 - /branches/V0.70d CRK HexaLotte/uart.c


 // ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Copyright (c) 04.2007 Holger Buss
// + only for non-profit use
// + www.MikroKopter.com
// + see the File "License.txt" for further Informations
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 
#include <avr/io.h>
#include <avr/interrupt.h>
#include <avr/wdt.h>
 
#include "eeprom.h"
#include "main.h"
#include "menu.h"
#include "timer0.h"
#include "uart.h"
#include "fc.h"
#include "_Settings.h"
#include "rc.h"
#if defined (USE_KILLAGREG) || defined (USE_MK3MAG)
#include "ubx.h"
#endif
#ifdef USE_MK3MAG
#include "mk3mag.h"
#endif
 
 
 
#define FALSE   0
#define TRUE    1
 
//int8_t test __attribute__ ((section (".noinit")));
uint8_t RequestVerInfo                  = FALSE;
uint8_t RequestExternalControl  = FALSE;
uint8_t RequestDisplay                  = FALSE;
uint8_t RequestDebugData                = FALSE;
uint8_t RequestDebugLabel               = 255;
uint8_t RequestChannelOnly              = FALSE;
uint8_t RemotePollDisplayLine   = 0;
 
volatile uint8_t txd_buffer[TXD_BUFFER_LEN];
volatile uint8_t rxd_buffer_locked = FALSE;
volatile uint8_t rxd_buffer[RXD_BUFFER_LEN];
volatile uint8_t txd_complete = TRUE;
volatile uint8_t ReceivedBytes = 0;
 
 
uint8_t PcAccess = 100;
uint8_t MotorTest[4] = {0,0,0,0};
uint8_t DubWiseKeys[4] = {0,0,0,0};
uint8_t MySlaveAddr = 0;
uint8_t ConfirmFrame;
 
DebugOut_t              DebugOut;
ExternControl_t ExternControl;
VersionInfo_t   VersionInfo;
 
int16_t  Debug_Timer;
 
#ifdef USE_MK3MAG
int16_t Compass_Timer;
#endif
 
 
const uint8_t ANALOG_LABEL[32][16] =
{
   //1234567890123456
    "IntegralNick    ", //0
    "IntegralRoll    ",
    "AccNick         ",
    "AccRoll         ",
    "GyroYaw         ",
    "ReadingHeight   ", //5
    "AccZ            ",
    "Gas             ",
    "Receiver Level  ",
    "Voltage         ",
#ifdef HEXAKOPTER
    "Motor FrontLeft ", //10
    "Motor FrontRight",
    "Motor RearLeft  ",
    "Motor RearRight ",
    "Motor Right     ",
    "Motor Left      ", //15
#else
    "Motor FrontLeft ", //10
    "Motor FrontRight",
    "Motor_RearLeft  ",
    "Motor_RearRight ",
    "Motor_Right     ",
    "Motor_Left      ", //15
#endif
    "Acc_Z           ",
    "SPI Error       ",
    "SPI Ok          ",
    "                ",
    "Servo           ", //20
    "Nick            ",
    "Roll            ",
    "                ",
    "                ",
    "                ", //25
    "                ",
    "                ",
    "                ",
    "                ",
    "GPS_Nick        ", //30
    "GPS_Roll        "
};
 
 
 
/****************************************************************/
/*              Initialization of the USART0                    */
/****************************************************************/
void USART0_Init (void)
{
        uint8_t sreg = SREG;
        uint16_t ubrr = (uint16_t) ((uint32_t) SYSCLK/(8 * USART0_BAUD) - 1);
 
        // disable all interrupts before configuration
        cli();
 
        // disable RX-Interrupt
        UCSR0B &= ~(1 << RXCIE0);
        // disable TX-Interrupt
        UCSR0B &= ~(1 << TXCIE0);
 
        // set direction of RXD0 and TXD0 pins
        // set RXD0 (PD0) as an input pin
        PORTD |= (1 << PORTD0);
        DDRD &= ~(1 << DDD0);
        // set TXD0 (PD1) as an output pin
        PORTD |= (1 << PORTD1);
        DDRD |=  (1 << DDD1);
 
        // USART0 Baud Rate Register
        // set clock divider
        UBRR0H = (uint8_t)(ubrr >> 8);
        UBRR0L = (uint8_t)ubrr;
 
        // USART0 Control and Status Register A, B, C
 
        // enable double speed operation in
        UCSR0A |= (1 << U2X0);
        // enable receiver and transmitter in
        UCSR0B = (1 << TXEN0) | (1 << RXEN0);
        // set asynchronous mode
        UCSR0C &= ~(1 << UMSEL01);
        UCSR0C &= ~(1 << UMSEL00);
        // no parity
        UCSR0C &= ~(1 << UPM01);
        UCSR0C &= ~(1 << UPM00);
        // 1 stop bit
        UCSR0C &= ~(1 << USBS0);
        // 8-bit
        UCSR0B &= ~(1 << UCSZ02);
        UCSR0C |=  (1 << UCSZ01);
        UCSR0C |=  (1 << UCSZ00);
 
                // flush receive buffer
        while ( UCSR0A & (1<<RXC0) ) UDR0;
 
        // enable interrupts at the end
        // enable RX-Interrupt
        UCSR0B |= (1 << RXCIE0);
        // enable TX-Interrupt
        UCSR0B |= (1 << TXCIE0);
 
        rxd_buffer_locked = FALSE;
        txd_complete = TRUE;
 
        Debug_Timer = SetDelay(200);
 
        #ifdef USE_MK3MAG
        Compass_Timer = SetDelay(220);
        #endif
 
        // restore global interrupt flags
    SREG = sreg;
}
 
/****************************************************************/
/*               USART0 transmitter ISR                         */
/****************************************************************/
ISR(USART0_TX_vect)
{
        static uint16_t ptr_txd_buffer = 0;
        uint8_t tmp_tx;
        if(!txd_complete) // transmission not completed
        {
                ptr_txd_buffer++;                    // die [0] wurde schon gesendet
                tmp_tx = txd_buffer[ptr_txd_buffer];
                // if terminating character or end of txd buffer was reached
                if((tmp_tx == '\r') || (ptr_txd_buffer == TXD_BUFFER_LEN))
                {
                        ptr_txd_buffer = 0; // reset txd pointer
                        txd_complete = 1; // stop transmission
                }
                UDR0 = tmp_tx; // send current byte will trigger this ISR again
        }
        // transmission completed
        else ptr_txd_buffer = 0;
}
 
/****************************************************************/
/*               USART0 receiver ISR                            */
/****************************************************************/
ISR(USART0_RX_vect)
{
        static uint16_t crc;
        static uint8_t ptr_rxd_buffer = 0;
        uint8_t crc1, crc2;
        uint8_t c;
 
        c = UDR0;  // catch the received byte
 
        #if defined (USE_KILLAGREG) || defined (USE_MK3MAG)
        // If the FC 1.0 cpu is used the ublox module should be conneced to rxd of the 1st uart.
        // The FC 1.1 /1.2 has the ATMEGA644p cpu with a 2nd uart to which the ublox should be connected.
        #if defined (__AVR_ATmega644P__)
        if(BoardRelease == 10) ubx_parser(c);
        #else
        ubx_parser(c);
        #endif
        #endif
 
        if(rxd_buffer_locked) return; // if rxd buffer is locked immediately return
 
        // the rxd buffer is unlocked
        if((ptr_rxd_buffer == 0) && (c == '#')) // if rxd buffer is empty and syncronisation character is received
        {
                rxd_buffer[ptr_rxd_buffer++] = c; // copy 1st byte to buffer
                crc = c; // init crc
        }
        #if 0
        else if (ptr_rxd_buffer == 1) // handle address
        {
                rxd_buffer[ptr_rxd_buffer++] = c; // copy byte to rxd buffer
                crc += c; // update crc
        }
        #endif
        else if (ptr_rxd_buffer < RXD_BUFFER_LEN) // collect incomming bytes
        {
                if(c != '\r') // no termination character
                {
                        rxd_buffer[ptr_rxd_buffer++] = c; // copy byte to rxd buffer
                        crc += c; // update crc
                }
                else // termination character was received
                {
                        // the last 2 bytes are no subject for checksum calculation
                        // they are the checksum itself
                        crc -= rxd_buffer[ptr_rxd_buffer-2];
                        crc -= rxd_buffer[ptr_rxd_buffer-1];
                        // calculate checksum from transmitted data
                        crc %= 4096;
                        crc1 = '=' + crc / 64;
                        crc2 = '=' + crc % 64;
                        // compare checksum to transmitted checksum bytes
                        if((crc1 == rxd_buffer[ptr_rxd_buffer-2]) && (crc2 == rxd_buffer[ptr_rxd_buffer-1]))
                        {   // checksum valid
                                rxd_buffer_locked = TRUE;          // lock the rxd buffer
                                ReceivedBytes = ptr_rxd_buffer;    // store number of received bytes
                                rxd_buffer[ptr_rxd_buffer] = '\r'; // set termination character
                                // if 2nd byte is an 'R' enable watchdog that will result in an reset
                                if(rxd_buffer[2] == 'R') {wdt_enable(WDTO_250MS);} // Reset-Commando
                        }
                        else
                        {       // checksum invalid
                                rxd_buffer_locked = FALSE; // unlock rxd buffer
                        }
                        ptr_rxd_buffer = 0; // reset rxd buffer pointer
                }
        }
        else // rxd buffer overrun
        {
                ptr_rxd_buffer = 0; // reset rxd buffer
                rxd_buffer_locked = FALSE; // unlock rxd buffer
        }
 
}
 
 
// --------------------------------------------------------------------------
void AddCRC(uint16_t datalen)
{
        uint16_t tmpCRC = 0, i;
        for(i = 0; i < datalen; i++)
        {
                tmpCRC += txd_buffer[i];
        }
        tmpCRC %= 4096;
        txd_buffer[i++] = '=' + tmpCRC / 64;
        txd_buffer[i++] = '=' + tmpCRC % 64;
        txd_buffer[i++] = '\r';
        txd_complete = FALSE;
        UDR0 = txd_buffer[0]; // initiates the transmittion (continued in the TXD ISR)
}
 
 
 
// --------------------------------------------------------------------------
void SendOutData(uint8_t cmd,uint8_t module, uint8_t *snd, uint8_t len)
{
        uint16_t pt = 0;
        uint8_t a,b,c;
        uint8_t ptr = 0;
 
        txd_buffer[pt++] = '#';         // Start character
        txd_buffer[pt++] = module;      // Address (a=0; b=1,...)
        txd_buffer[pt++] = cmd;         // Command
 
        while(len)
        {
                if(len) { a = snd[ptr++]; len--;} else a = 0;
                if(len) { b = snd[ptr++]; len--;} else b = 0;
                if(len) { c = snd[ptr++]; len--;} else c = 0;
                txd_buffer[pt++] = '=' + (a >> 2);
                txd_buffer[pt++] = '=' + (((a & 0x03) << 4) | ((b & 0xf0) >> 4));
                txd_buffer[pt++] = '=' + (((b & 0x0f) << 2) | ((c & 0xc0) >> 6));
                txd_buffer[pt++] = '=' + ( c & 0x3f);
        }
        AddCRC(pt); // add checksum after data block and initates the transmission
}
 
 
// --------------------------------------------------------------------------
void Decode64(uint8_t *ptrOut, uint8_t len, uint8_t ptrIn, uint8_t max)
{
        uint8_t a,b,c,d;
        uint8_t ptr = 0;
        uint8_t x,y,z;
        while(len)
        {
                a = rxd_buffer[ptrIn++] - '=';
                b = rxd_buffer[ptrIn++] - '=';
                c = rxd_buffer[ptrIn++] - '=';
                d = rxd_buffer[ptrIn++] - '=';
                if(ptrIn > max - 2) break;
 
                x = (a << 2) | (b >> 4);
                y = ((b & 0x0f) << 4) | (c >> 2);
                z = ((c & 0x03) << 6) | d;
 
                if(len--) ptrOut[ptr++] = x; else break;
                if(len--) ptrOut[ptr++] = y; else break;
                if(len--) ptrOut[ptr++] = z; else break;
        }
}
 
 
// --------------------------------------------------------------------------
void USART0_ProcessRxData(void)
{
        // if data in the rxd buffer are not locked immediately return
        if(!rxd_buffer_locked) return;
 
        #if  !defined (USE_KILLAGREG)  && !defined (USE_NAVICTRL)
        uint16_t tmp_int_arr1[1]; // local int buffer
        #endif
        uint8_t tmp_char_arr2[2]; // local char buffer
 
 
        switch(rxd_buffer[2])
        {
                #ifdef USE_MK3MAG
                case 'K':// Compass value
                        Decode64((uint8_t *) &tmp_int_arr1[0], sizeof(tmp_int_arr1), 3, ReceivedBytes);
                        CompassHeading = tmp_int_arr1[0];
                        CompassOffCourse = ((540 + CompassHeading - CompassCourse) % 360) - 180;
                        break;
                #endif
                case 'a':// Labels of the Analog Debug outputs
                        Decode64((uint8_t *) &tmp_char_arr2[0], sizeof(tmp_char_arr2), 3, ReceivedBytes);
                        RequestDebugLabel = tmp_char_arr2[0];
                        PcAccess = 255;
                        break;
                case 'b': // extern control
                        Decode64((uint8_t *) &ExternControl,sizeof(ExternControl), 3, ReceivedBytes);
                        RemoteButtons |= ExternControl.RemoteButtons;
                        ConfirmFrame = ExternControl.Frame;
                        PcAccess = 255;
                        break;
                case 'c': // extern control with debug request
                        Decode64((uint8_t *) &ExternControl,sizeof(ExternControl),3,ReceivedBytes);
                        RemoteButtons |= ExternControl.RemoteButtons;
                        ConfirmFrame = ExternControl.Frame;
                        RequestDebugData = TRUE;
                        PcAccess = 255;
                        break;
                case 'h':// x-1 display columns
                        Decode64((uint8_t *) &tmp_char_arr2[0],sizeof(tmp_char_arr2),3,ReceivedBytes);
                        RemoteButtons |= tmp_char_arr2[0];
                        if(tmp_char_arr2[1] == 255) RequestChannelOnly = TRUE;
                        else RequestChannelOnly = FALSE; // keine Displaydaten
                        RequestDisplay = TRUE;
                        break;
                case 't':// motor test
                        Decode64((uint8_t *) &MotorTest[0],sizeof(MotorTest),3,ReceivedBytes);
                        PcAccess = 255;
                        break;
                case 'k':// keys from DubWise
                        Decode64((uint8_t *) &DubWiseKeys[0],sizeof(DubWiseKeys),3,ReceivedBytes);
                        ConfirmFrame = DubWiseKeys[3];
                        PcAccess = 255;
                        break;
                case 'v': // get version and board release
                        RequestVerInfo = TRUE;
                        break;
                case 'g':// get external control data
                        RequestExternalControl = TRUE;
                        break;
                case 'q':// get settings
                        Decode64((uint8_t *) &tmp_char_arr2[0],sizeof(tmp_char_arr2),3,ReceivedBytes);
                        while(!txd_complete);
                        if(tmp_char_arr2[0] != 0xff)
                        {
                                if(tmp_char_arr2[0] > 5) tmp_char_arr2[0] = 5; // limit to 5
                                // load requested parameter set
                                ParamSet_ReadFromEEProm(tmp_char_arr2[0]);
                                SendOutData('L' + tmp_char_arr2[0] -1,MySlaveAddr,(uint8_t *) &ParamSet.ChannelAssignment[0],PARAMSET_STRUCT_LEN);
                        }
                        else // send active parameter set
                        SendOutData('L' + GetParamByte(PID_ACTIVE_SET)-1,MySlaveAddr,(uint8_t *) &ParamSet.ChannelAssignment[0],PARAMSET_STRUCT_LEN);
 
                        break;
 
                case 'l':
                case 'm':
                case 'n':
                case 'o':
                case 'p': // save parameterset
                        Decode64((uint8_t *) &ParamSet.ChannelAssignment[0],PARAMSET_STRUCT_LEN,3,ReceivedBytes);
                        ParamSet_WriteToEEProm(rxd_buffer[2] - 'l' + 1);
                        TurnOver180Nick = (int32_t) ParamSet.AngleTurnOverNick * 2500L;
                        TurnOver180Roll = (int32_t) ParamSet.AngleTurnOverRoll * 2500L;
                        Beep(GetActiveParamSet());
                        break;
 
 
        }
        // unlock the rxd buffer after processing
        rxd_buffer_locked = FALSE;
}
 
//############################################################################
//Routine für die Serielle Ausgabe
int16_t uart_putchar (int8_t c)
//############################################################################
{
        if (c == '\n')
                uart_putchar('\r');
        // wait until previous character was send
        loop_until_bit_is_set(UCSR0A, UDRE0);
        //Ausgabe des Zeichens
        UDR0 = c;
        return (0);
}
 
 
//---------------------------------------------------------------------------------------------
void USART0_TransmitTxData(void)
{
        if(!txd_complete) return;
 
        if(RequestExternalControl && txd_complete)            // Bei Get werden die vom PC einstellbaren Werte vom PC zurückgelesen
        {
                SendOutData('G',MySlaveAddr,(uint8_t *) &ExternControl,sizeof(ExternControl));
                RequestExternalControl = FALSE;
        }
 
        #ifdef USE_MK3MAG
    if((CheckDelay(Compass_Timer)) && txd_complete)
        {
                ToMk3Mag.Attitude[0] = (int16_t) (IntegralNick / 108);  // approx. 0,1 Deg
                ToMk3Mag.Attitude[1] = (int16_t) (IntegralRoll / 108);   // approx. 0,1 Deg
                ToMk3Mag.UserParam[0] = FCParam.UserParam1;
                ToMk3Mag.UserParam[1] = FCParam.UserParam2;
                ToMk3Mag.CalState = CompassCalState;
                SendOutData('w',MySlaveAddr,(uint8_t *) &ToMk3Mag,sizeof(ToMk3Mag));
                // the last state is 5 and should be send only once to avoid multiple flash writing
                if(CompassCalState > 4)  CompassCalState = 0;
                Compass_Timer = SetDelay(99);
        }
        #endif
 
    if((CheckDelay(Debug_Timer) || RequestDebugData) && txd_complete)
    {
          SendOutData('D',MySlaveAddr,(uint8_t *) &DebugOut,sizeof(DebugOut));
          RequestDebugData = FALSE;
          Debug_Timer = SetDelay(MIN_DEBUG_INTERVALL);
    }
 
    if(RequestDebugLabel != 255) // Texte für die Analogdaten
     {
      SendOutData('A',RequestDebugLabel + '0',(uint8_t *) ANALOG_LABEL[RequestDebugLabel],16);
      RequestDebugLabel = 255;
         }
     if(ConfirmFrame && txd_complete)   // Datensatz ohne CRC bestätigen
         {
      txd_buffer[0] = '#';
      txd_buffer[1] = ConfirmFrame;
      txd_buffer[2] = '\r';
      txd_complete = 0;
      ConfirmFrame = 0;
      UDR0 = txd_buffer[0];
     }
     if(RequestDisplay && txd_complete)
         {
      LCD_PrintMenu();
          RequestDisplay = FALSE;
      if(++RemotePollDisplayLine == 4 || RequestChannelOnly)
      {
       SendOutData('4',0,(uint8_t *)&PPM_in,sizeof(PPM_in));   // DisplayZeile übertragen
       RemotePollDisplayLine = -1;
      }
      else  SendOutData('0' + RemotePollDisplayLine,0,(uint8_t *)&DisplayBuff[20 * RemotePollDisplayLine],20);   // DisplayZeile übertragen
         }
    if(RequestVerInfo && txd_complete)
     {
      SendOutData('V',MySlaveAddr,(uint8_t *) &VersionInfo,sizeof(VersionInfo));
          RequestVerInfo = FALSE;
     }
 
}
 
 

Rev 942	Rev 943
1	// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++	1	// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
2	// + Copyright (c) 04.2007 Holger Buss	2	// + Copyright (c) 04.2007 Holger Buss
3	// + only for non-profit use	3	// + only for non-profit use
4	// + www.MikroKopter.com	4	// + www.MikroKopter.com
5	// + see the File "License.txt" for further Informations	5	// + see the File "License.txt" for further Informations
6	// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++	6	// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
7		7
8	#include <avr/io.h>	8	#include <avr/io.h>
9	#include <avr/interrupt.h>	9	#include <avr/interrupt.h>
10	#include <avr/wdt.h>	10	#include <avr/wdt.h>
11		11
12	#include "eeprom.h"	12	#include "eeprom.h"
13	#include "main.h"	13	#include "main.h"
14	#include "menu.h"	14	#include "menu.h"
15	#include "timer0.h"	15	#include "timer0.h"
16	#include "uart.h"	16	#include "uart.h"
17	#include "fc.h"	17	#include "fc.h"
18	#include "_Settings.h"	18	#include "_Settings.h"
19	#include "rc.h"	19	#include "rc.h"
20	#if defined (USE_KILLAGREG) \|\| defined (USE_MK3MAG)	20	#if defined (USE_KILLAGREG) \|\| defined (USE_MK3MAG)
21	#include "ubx.h"	21	#include "ubx.h"
22	#endif	22	#endif
23	#ifdef USE_MK3MAG	23	#ifdef USE_MK3MAG
24	#include "mk3mag.h"	24	#include "mk3mag.h"
25	#endif	25	#endif
26		26
27		27
28		28
29	#define FALSE 0	29	#define FALSE 0
30	#define TRUE 1	30	#define TRUE 1
31		31
32	//int8_t test __attribute__ ((section (".noinit")));	32	//int8_t test __attribute__ ((section (".noinit")));
33	uint8_t RequestVerInfo = FALSE;	33	uint8_t RequestVerInfo = FALSE;
34	uint8_t RequestExternalControl = FALSE;	34	uint8_t RequestExternalControl = FALSE;
35	uint8_t RequestDisplay = FALSE;	35	uint8_t RequestDisplay = FALSE;
36	uint8_t RequestDebugData = FALSE;	36	uint8_t RequestDebugData = FALSE;
37	uint8_t RequestDebugLabel = 255;	37	uint8_t RequestDebugLabel = 255;
38	uint8_t RequestChannelOnly = FALSE;	38	uint8_t RequestChannelOnly = FALSE;
39	uint8_t RemotePollDisplayLine = 0;	39	uint8_t RemotePollDisplayLine = 0;
40		40
41	volatile uint8_t txd_buffer[TXD_BUFFER_LEN];	41	volatile uint8_t txd_buffer[TXD_BUFFER_LEN];
42	volatile uint8_t rxd_buffer_locked = FALSE;	42	volatile uint8_t rxd_buffer_locked = FALSE;
43	volatile uint8_t rxd_buffer[RXD_BUFFER_LEN];	43	volatile uint8_t rxd_buffer[RXD_BUFFER_LEN];
44	volatile uint8_t txd_complete = TRUE;	44	volatile uint8_t txd_complete = TRUE;
45	volatile uint8_t ReceivedBytes = 0;	45	volatile uint8_t ReceivedBytes = 0;
46		46
47		47
48	uint8_t PcAccess = 100;	48	uint8_t PcAccess = 100;
49	uint8_t MotorTest[4] = {0,0,0,0};	49	uint8_t MotorTest[4] = {0,0,0,0};
50	uint8_t DubWiseKeys[4] = {0,0,0,0};	50	uint8_t DubWiseKeys[4] = {0,0,0,0};
51	uint8_t MySlaveAddr = 0;	51	uint8_t MySlaveAddr = 0;
52	uint8_t ConfirmFrame;	52	uint8_t ConfirmFrame;
53		53
54	DebugOut_t DebugOut;	54	DebugOut_t DebugOut;
55	ExternControl_t ExternControl;	55	ExternControl_t ExternControl;
56	VersionInfo_t VersionInfo;	56	VersionInfo_t VersionInfo;
57		57
58	int16_t Debug_Timer;	58	int16_t Debug_Timer;
59		59
60	#ifdef USE_MK3MAG	60	#ifdef USE_MK3MAG
61	int16_t Compass_Timer;	61	int16_t Compass_Timer;
62	#endif	62	#endif
63		63
64		64
65	const uint8_t ANALOG_LABEL[32][16] =	65	const uint8_t ANALOG_LABEL[32][16] =
66	{	66	{
67	//1234567890123456	67	//1234567890123456
68	"IntegralNick ", //0	68	"IntegralNick ", //0
69	"IntegralRoll ",	69	"IntegralRoll ",
70	"AccNick ",	70	"AccNick ",
71	"AccRoll ",	71	"AccRoll ",
72	"GyroYaw ",	72	"GyroYaw ",
73	"ReadingHeight ", //5	73	"ReadingHeight ", //5
74	"AccZ ",	74	"AccZ ",
75	"Gas ",	75	"Gas ",
76	"CompassHeading ",	76	"Receiver Level ",
77	"Voltage ",	77	"Voltage ",
-		78	#ifdef HEXAKOPTER
78	"Receiver Level ", //10	79	"Motor FrontLeft ", //10
-		80	"Motor FrontRight",
-		81	"Motor RearLeft ",
79	"YawGyroHeading ",	82	"Motor RearRight ",
80	"Motor_Front ",	83	"Motor Right ",
-		84	"Motor Left ", //15
-		85	#else
-		86	"Motor FrontLeft ", //10
-		87	"Motor FrontRight",
81	"Motor_Rear ",	88	"Motor_RearLeft ",
-		89	"Motor_RearRight ",
82	"Motor_Right ",	90	"Motor_Right ",
83	"Motor_Left ", //15	91	"Motor_Left ", //15
-		92	#endif
84	" ",	93	"Acc_Z ",
85	"SPI Error ",	94	"SPI Error ",
86	"SPI Ok ",	95	"SPI Ok ",
87	" ",	96	" ",
88	"Servo ", //20	97	"Servo ", //20
89	"Nick ",	98	"Nick ",
90	"Roll ",	99	"Roll ",
91	" ",	100	" ",
92	" ",	101	" ",
93	" ", //25	102	" ", //25
94	" ",	103	" ",
95	" ",	104	" ",
96	" ",	105	" ",
97	" ",	106	" ",
98	"GPS_Nick ", //30	107	"GPS_Nick ", //30
99	"GPS_Roll "	108	"GPS_Roll "
100	};	109	};
101		110
102		111
103		112
104	/****************************************************************/	113	/****************************************************************/
105	/* Initialization of the USART0 */	114	/* Initialization of the USART0 */
106	/****************************************************************/	115	/****************************************************************/
107	void USART0_Init (void)	116	void USART0_Init (void)
108	{	117	{
109	uint8_t sreg = SREG;	118	uint8_t sreg = SREG;
110	uint16_t ubrr = (uint16_t) ((uint32_t) SYSCLK/(8 * USART0_BAUD) - 1);	119	uint16_t ubrr = (uint16_t) ((uint32_t) SYSCLK/(8 * USART0_BAUD) - 1);
111		120
112	// disable all interrupts before configuration	121	// disable all interrupts before configuration
113	cli();	122	cli();
114		123
115	// disable RX-Interrupt	124	// disable RX-Interrupt
116	UCSR0B &= ~(1 << RXCIE0);	125	UCSR0B &= ~(1 << RXCIE0);
117	// disable TX-Interrupt	126	// disable TX-Interrupt
118	UCSR0B &= ~(1 << TXCIE0);	127	UCSR0B &= ~(1 << TXCIE0);
119		128
120	// set direction of RXD0 and TXD0 pins	129	// set direction of RXD0 and TXD0 pins
121	// set RXD0 (PD0) as an input pin	130	// set RXD0 (PD0) as an input pin
122	PORTD \|= (1 << PORTD0);	131	PORTD \|= (1 << PORTD0);
123	DDRD &= ~(1 << DDD0);	132	DDRD &= ~(1 << DDD0);
124	// set TXD0 (PD1) as an output pin	133	// set TXD0 (PD1) as an output pin
125	PORTD \|= (1 << PORTD1);	134	PORTD \|= (1 << PORTD1);
126	DDRD \|= (1 << DDD1);	135	DDRD \|= (1 << DDD1);
127		136
128	// USART0 Baud Rate Register	137	// USART0 Baud Rate Register
129	// set clock divider	138	// set clock divider
130	UBRR0H = (uint8_t)(ubrr >> 8);	139	UBRR0H = (uint8_t)(ubrr >> 8);
131	UBRR0L = (uint8_t)ubrr;	140	UBRR0L = (uint8_t)ubrr;
132		141
133	// USART0 Control and Status Register A, B, C	142	// USART0 Control and Status Register A, B, C
134		143
135	// enable double speed operation in	144	// enable double speed operation in
136	UCSR0A \|= (1 << U2X0);	145	UCSR0A \|= (1 << U2X0);
137	// enable receiver and transmitter in	146	// enable receiver and transmitter in
138	UCSR0B = (1 << TXEN0) \| (1 << RXEN0);	147	UCSR0B = (1 << TXEN0) \| (1 << RXEN0);
139	// set asynchronous mode	148	// set asynchronous mode
140	UCSR0C &= ~(1 << UMSEL01);	149	UCSR0C &= ~(1 << UMSEL01);
141	UCSR0C &= ~(1 << UMSEL00);	150	UCSR0C &= ~(1 << UMSEL00);
142	// no parity	151	// no parity
143	UCSR0C &= ~(1 << UPM01);	152	UCSR0C &= ~(1 << UPM01);
144	UCSR0C &= ~(1 << UPM00);	153	UCSR0C &= ~(1 << UPM00);
145	// 1 stop bit	154	// 1 stop bit
146	UCSR0C &= ~(1 << USBS0);	155	UCSR0C &= ~(1 << USBS0);
147	// 8-bit	156	// 8-bit
148	UCSR0B &= ~(1 << UCSZ02);	157	UCSR0B &= ~(1 << UCSZ02);
149	UCSR0C \|= (1 << UCSZ01);	158	UCSR0C \|= (1 << UCSZ01);
150	UCSR0C \|= (1 << UCSZ00);	159	UCSR0C \|= (1 << UCSZ00);
151		160
152	// flush receive buffer	161	// flush receive buffer
153	while ( UCSR0A & (1<<RXC0) ) UDR0;	162	while ( UCSR0A & (1<<RXC0) ) UDR0;
154		163
155	// enable interrupts at the end	164	// enable interrupts at the end
156	// enable RX-Interrupt	165	// enable RX-Interrupt
157	UCSR0B \|= (1 << RXCIE0);	166	UCSR0B \|= (1 << RXCIE0);
158	// enable TX-Interrupt	167	// enable TX-Interrupt
159	UCSR0B \|= (1 << TXCIE0);	168	UCSR0B \|= (1 << TXCIE0);
160		169
161	rxd_buffer_locked = FALSE;	170	rxd_buffer_locked = FALSE;
162	txd_complete = TRUE;	171	txd_complete = TRUE;
163		172
164	Debug_Timer = SetDelay(200);	173	Debug_Timer = SetDelay(200);
165		174
166	#ifdef USE_MK3MAG	175	#ifdef USE_MK3MAG
167	Compass_Timer = SetDelay(220);	176	Compass_Timer = SetDelay(220);
168	#endif	177	#endif
169		178
170	// restore global interrupt flags	179	// restore global interrupt flags
171	SREG = sreg;	180	SREG = sreg;
172	}	181	}
173		182
174	/****************************************************************/	183	/****************************************************************/
175	/* USART0 transmitter ISR */	184	/* USART0 transmitter ISR */
176	/****************************************************************/	185	/****************************************************************/
177	ISR(USART0_TX_vect)	186	ISR(USART0_TX_vect)
178	{	187	{
179	static uint16_t ptr_txd_buffer = 0;	188	static uint16_t ptr_txd_buffer = 0;
180	uint8_t tmp_tx;	189	uint8_t tmp_tx;
181	if(!txd_complete) // transmission not completed	190	if(!txd_complete) // transmission not completed
182	{	191	{
183	ptr_txd_buffer++; // die [0] wurde schon gesendet	192	ptr_txd_buffer++; // die [0] wurde schon gesendet
184	tmp_tx = txd_buffer[ptr_txd_buffer];	193	tmp_tx = txd_buffer[ptr_txd_buffer];
185	// if terminating character or end of txd buffer was reached	194	// if terminating character or end of txd buffer was reached
186	if((tmp_tx == '\r') \|\| (ptr_txd_buffer == TXD_BUFFER_LEN))	195	if((tmp_tx == '\r') \|\| (ptr_txd_buffer == TXD_BUFFER_LEN))
187	{	196	{
188	ptr_txd_buffer = 0; // reset txd pointer	197	ptr_txd_buffer = 0; // reset txd pointer
189	txd_complete = 1; // stop transmission	198	txd_complete = 1; // stop transmission
190	}	199	}
191	UDR0 = tmp_tx; // send current byte will trigger this ISR again	200	UDR0 = tmp_tx; // send current byte will trigger this ISR again
192	}	201	}
193	// transmission completed	202	// transmission completed
194	else ptr_txd_buffer = 0;	203	else ptr_txd_buffer = 0;
195	}	204	}
196		205
197	/****************************************************************/	206	/****************************************************************/
198	/* USART0 receiver ISR */	207	/* USART0 receiver ISR */
199	/****************************************************************/	208	/****************************************************************/
200	ISR(USART0_RX_vect)	209	ISR(USART0_RX_vect)
201	{	210	{
202	static uint16_t crc;	211	static uint16_t crc;
203	static uint8_t ptr_rxd_buffer = 0;	212	static uint8_t ptr_rxd_buffer = 0;
204	uint8_t crc1, crc2;	213	uint8_t crc1, crc2;
205	uint8_t c;	214	uint8_t c;
206		215
207	c = UDR0; // catch the received byte	216	c = UDR0; // catch the received byte
208		217
209	#if defined (USE_KILLAGREG) \|\| defined (USE_MK3MAG)	218	#if defined (USE_KILLAGREG) \|\| defined (USE_MK3MAG)
210	// If the FC 1.0 cpu is used the ublox module should be conneced to rxd of the 1st uart.	219	// If the FC 1.0 cpu is used the ublox module should be conneced to rxd of the 1st uart.
211	// The FC 1.1 /1.2 has the ATMEGA644p cpu with a 2nd uart to which the ublox should be connected.	220	// The FC 1.1 /1.2 has the ATMEGA644p cpu with a 2nd uart to which the ublox should be connected.
212	#if defined (__AVR_ATmega644P__)	221	#if defined (__AVR_ATmega644P__)
213	if(BoardRelease == 10) ubx_parser(c);	222	if(BoardRelease == 10) ubx_parser(c);
214	#else	223	#else
215	ubx_parser(c);	224	ubx_parser(c);
216	#endif	225	#endif
217	#endif	226	#endif
218		227
219	if(rxd_buffer_locked) return; // if rxd buffer is locked immediately return	228	if(rxd_buffer_locked) return; // if rxd buffer is locked immediately return
220		229
221	// the rxd buffer is unlocked	230	// the rxd buffer is unlocked
222	if((ptr_rxd_buffer == 0) && (c == '#')) // if rxd buffer is empty and syncronisation character is received	231	if((ptr_rxd_buffer == 0) && (c == '#')) // if rxd buffer is empty and syncronisation character is received
223	{	232	{
224	rxd_buffer[ptr_rxd_buffer++] = c; // copy 1st byte to buffer	233	rxd_buffer[ptr_rxd_buffer++] = c; // copy 1st byte to buffer
225	crc = c; // init crc	234	crc = c; // init crc
226	}	235	}
227	#if 0	236	#if 0
228	else if (ptr_rxd_buffer == 1) // handle address	237	else if (ptr_rxd_buffer == 1) // handle address
229	{	238	{
230	rxd_buffer[ptr_rxd_buffer++] = c; // copy byte to rxd buffer	239	rxd_buffer[ptr_rxd_buffer++] = c; // copy byte to rxd buffer
231	crc += c; // update crc	240	crc += c; // update crc
232	}	241	}
233	#endif	242	#endif
234	else if (ptr_rxd_buffer < RXD_BUFFER_LEN) // collect incomming bytes	243	else if (ptr_rxd_buffer < RXD_BUFFER_LEN) // collect incomming bytes
235	{	244	{
236	if(c != '\r') // no termination character	245	if(c != '\r') // no termination character
237	{	246	{
238	rxd_buffer[ptr_rxd_buffer++] = c; // copy byte to rxd buffer	247	rxd_buffer[ptr_rxd_buffer++] = c; // copy byte to rxd buffer
239	crc += c; // update crc	248	crc += c; // update crc
240	}	249	}
241	else // termination character was received	250	else // termination character was received
242	{	251	{
243	// the last 2 bytes are no subject for checksum calculation	252	// the last 2 bytes are no subject for checksum calculation
244	// they are the checksum itself	253	// they are the checksum itself
245	crc -= rxd_buffer[ptr_rxd_buffer-2];	254	crc -= rxd_buffer[ptr_rxd_buffer-2];
246	crc -= rxd_buffer[ptr_rxd_buffer-1];	255	crc -= rxd_buffer[ptr_rxd_buffer-1];
247	// calculate checksum from transmitted data	256	// calculate checksum from transmitted data
248	crc %= 4096;	257	crc %= 4096;
249	crc1 = '=' + crc / 64;	258	crc1 = '=' + crc / 64;
250	crc2 = '=' + crc % 64;	259	crc2 = '=' + crc % 64;
251	// compare checksum to transmitted checksum bytes	260	// compare checksum to transmitted checksum bytes
252	if((crc1 == rxd_buffer[ptr_rxd_buffer-2]) && (crc2 == rxd_buffer[ptr_rxd_buffer-1]))	261	if((crc1 == rxd_buffer[ptr_rxd_buffer-2]) && (crc2 == rxd_buffer[ptr_rxd_buffer-1]))
253	{ // checksum valid	262	{ // checksum valid
254	rxd_buffer_locked = TRUE; // lock the rxd buffer	263	rxd_buffer_locked = TRUE; // lock the rxd buffer
255	ReceivedBytes = ptr_rxd_buffer; // store number of received bytes	264	ReceivedBytes = ptr_rxd_buffer; // store number of received bytes
256	rxd_buffer[ptr_rxd_buffer] = '\r'; // set termination character	265	rxd_buffer[ptr_rxd_buffer] = '\r'; // set termination character
257	// if 2nd byte is an 'R' enable watchdog that will result in an reset	266	// if 2nd byte is an 'R' enable watchdog that will result in an reset
258	if(rxd_buffer[2] == 'R') {wdt_enable(WDTO_250MS);} // Reset-Commando	267	if(rxd_buffer[2] == 'R') {wdt_enable(WDTO_250MS);} // Reset-Commando
259	}	268	}
260	else	269	else
261	{ // checksum invalid	270	{ // checksum invalid
262	rxd_buffer_locked = FALSE; // unlock rxd buffer	271	rxd_buffer_locked = FALSE; // unlock rxd buffer
263	}	272	}
264	ptr_rxd_buffer = 0; // reset rxd buffer pointer	273	ptr_rxd_buffer = 0; // reset rxd buffer pointer
265	}	274	}
266	}	275	}
267	else // rxd buffer overrun	276	else // rxd buffer overrun
268	{	277	{
269	ptr_rxd_buffer = 0; // reset rxd buffer	278	ptr_rxd_buffer = 0; // reset rxd buffer
270	rxd_buffer_locked = FALSE; // unlock rxd buffer	279	rxd_buffer_locked = FALSE; // unlock rxd buffer
271	}	280	}
272		281
273	}	282	}
274		283
275		284
276	// --------------------------------------------------------------------------	285	// --------------------------------------------------------------------------
277	void AddCRC(uint16_t datalen)	286	void AddCRC(uint16_t datalen)
278	{	287	{
279	uint16_t tmpCRC = 0, i;	288	uint16_t tmpCRC = 0, i;
280	for(i = 0; i < datalen; i++)	289	for(i = 0; i < datalen; i++)
281	{	290	{
282	tmpCRC += txd_buffer[i];	291	tmpCRC += txd_buffer[i];
283	}	292	}
284	tmpCRC %= 4096;	293	tmpCRC %= 4096;
285	txd_buffer[i++] = '=' + tmpCRC / 64;	294	txd_buffer[i++] = '=' + tmpCRC / 64;
286	txd_buffer[i++] = '=' + tmpCRC % 64;	295	txd_buffer[i++] = '=' + tmpCRC % 64;
287	txd_buffer[i++] = '\r';	296	txd_buffer[i++] = '\r';
288	txd_complete = FALSE;	297	txd_complete = FALSE;
289	UDR0 = txd_buffer[0]; // initiates the transmittion (continued in the TXD ISR)	298	UDR0 = txd_buffer[0]; // initiates the transmittion (continued in the TXD ISR)
290	}	299	}
291		300
292		301
293		302
294	// --------------------------------------------------------------------------	303	// --------------------------------------------------------------------------
295	void SendOutData(uint8_t cmd,uint8_t module, uint8_t *snd, uint8_t len)	304	void SendOutData(uint8_t cmd,uint8_t module, uint8_t *snd, uint8_t len)
296	{	305	{
297	uint16_t pt = 0;	306	uint16_t pt = 0;
298	uint8_t a,b,c;	307	uint8_t a,b,c;
299	uint8_t ptr = 0;	308	uint8_t ptr = 0;
300		309
301	txd_buffer[pt++] = '#'; // Start character	310	txd_buffer[pt++] = '#'; // Start character
302	txd_buffer[pt++] = module; // Address (a=0; b=1,...)	311	txd_buffer[pt++] = module; // Address (a=0; b=1,...)
303	txd_buffer[pt++] = cmd; // Command	312	txd_buffer[pt++] = cmd; // Command
304		313
305	while(len)	314	while(len)
306	{	315	{
307	if(len) { a = snd[ptr++]; len--;} else a = 0;	316	if(len) { a = snd[ptr++]; len--;} else a = 0;
308	if(len) { b = snd[ptr++]; len--;} else b = 0;	317	if(len) { b = snd[ptr++]; len--;} else b = 0;
309	if(len) { c = snd[ptr++]; len--;} else c = 0;	318	if(len) { c = snd[ptr++]; len--;} else c = 0;
310	txd_buffer[pt++] = '=' + (a >> 2);	319	txd_buffer[pt++] = '=' + (a >> 2);
311	txd_buffer[pt++] = '=' + (((a & 0x03) << 4) \| ((b & 0xf0) >> 4));	320	txd_buffer[pt++] = '=' + (((a & 0x03) << 4) \| ((b & 0xf0) >> 4));
312	txd_buffer[pt++] = '=' + (((b & 0x0f) << 2) \| ((c & 0xc0) >> 6));	321	txd_buffer[pt++] = '=' + (((b & 0x0f) << 2) \| ((c & 0xc0) >> 6));
313	txd_buffer[pt++] = '=' + ( c & 0x3f);	322	txd_buffer[pt++] = '=' + ( c & 0x3f);
314	}	323	}
315	AddCRC(pt); // add checksum after data block and initates the transmission	324	AddCRC(pt); // add checksum after data block and initates the transmission
316	}	325	}
317		326
318		327
319	// --------------------------------------------------------------------------	328	// --------------------------------------------------------------------------
320	void Decode64(uint8_t *ptrOut, uint8_t len, uint8_t ptrIn, uint8_t max)	329	void Decode64(uint8_t *ptrOut, uint8_t len, uint8_t ptrIn, uint8_t max)
321	{	330	{
322	uint8_t a,b,c,d;	331	uint8_t a,b,c,d;
323	uint8_t ptr = 0;	332	uint8_t ptr = 0;
324	uint8_t x,y,z;	333	uint8_t x,y,z;
325	while(len)	334	while(len)
326	{	335	{
327	a = rxd_buffer[ptrIn++] - '=';	336	a = rxd_buffer[ptrIn++] - '=';
328	b = rxd_buffer[ptrIn++] - '=';	337	b = rxd_buffer[ptrIn++] - '=';
329	c = rxd_buffer[ptrIn++] - '=';	338	c = rxd_buffer[ptrIn++] - '=';
330	d = rxd_buffer[ptrIn++] - '=';	339	d = rxd_buffer[ptrIn++] - '=';
331	if(ptrIn > max - 2) break;	340	if(ptrIn > max - 2) break;
332		341
333	x = (a << 2) \| (b >> 4);	342	x = (a << 2) \| (b >> 4);
334	y = ((b & 0x0f) << 4) \| (c >> 2);	343	y = ((b & 0x0f) << 4) \| (c >> 2);
335	z = ((c & 0x03) << 6) \| d;	344	z = ((c & 0x03) << 6) \| d;
336		345
337	if(len--) ptrOut[ptr++] = x; else break;	346	if(len--) ptrOut[ptr++] = x; else break;
338	if(len--) ptrOut[ptr++] = y; else break;	347	if(len--) ptrOut[ptr++] = y; else break;
339	if(len--) ptrOut[ptr++] = z; else break;	348	if(len--) ptrOut[ptr++] = z; else break;
340	}	349	}
341	}	350	}
342		351
343		352
344	// --------------------------------------------------------------------------	353	// --------------------------------------------------------------------------
345	void USART0_ProcessRxData(void)	354	void USART0_ProcessRxData(void)
346	{	355	{
347	// if data in the rxd buffer are not locked immediately return	356	// if data in the rxd buffer are not locked immediately return
348	if(!rxd_buffer_locked) return;	357	if(!rxd_buffer_locked) return;
349		358
350	#if !defined (USE_KILLAGREG) && !defined (USE_NAVICTRL)	359	#if !defined (USE_KILLAGREG) && !defined (USE_NAVICTRL)
351	uint16_t tmp_int_arr1[1]; // local int buffer	360	uint16_t tmp_int_arr1[1]; // local int buffer
352	#endif	361	#endif
353	uint8_t tmp_char_arr2[2]; // local char buffer	362	uint8_t tmp_char_arr2[2]; // local char buffer
354		363
355		364
356	switch(rxd_buffer[2])	365	switch(rxd_buffer[2])
357	{	366	{
358	#ifdef USE_MK3MAG	367	#ifdef USE_MK3MAG
359	case 'K':// Compass value	368	case 'K':// Compass value
360	Decode64((uint8_t *) &tmp_int_arr1[0], sizeof(tmp_int_arr1), 3, ReceivedBytes);	369	Decode64((uint8_t *) &tmp_int_arr1[0], sizeof(tmp_int_arr1), 3, ReceivedBytes);
361	CompassHeading = tmp_int_arr1[0];	370	CompassHeading = tmp_int_arr1[0];
362	CompassOffCourse = ((540 + CompassHeading - CompassCourse) % 360) - 180;	371	CompassOffCourse = ((540 + CompassHeading - CompassCourse) % 360) - 180;
363	break;	372	break;
364	#endif	373	#endif
365	case 'a':// Labels of the Analog Debug outputs	374	case 'a':// Labels of the Analog Debug outputs
366	Decode64((uint8_t *) &tmp_char_arr2[0], sizeof(tmp_char_arr2), 3, ReceivedBytes);	375	Decode64((uint8_t *) &tmp_char_arr2[0], sizeof(tmp_char_arr2), 3, ReceivedBytes);
367	RequestDebugLabel = tmp_char_arr2[0];	376	RequestDebugLabel = tmp_char_arr2[0];
368	PcAccess = 255;	377	PcAccess = 255;
369	break;	378	break;
370	case 'b': // extern control	379	case 'b': // extern control
371	Decode64((uint8_t *) &ExternControl,sizeof(ExternControl), 3, ReceivedBytes);	380	Decode64((uint8_t *) &ExternControl,sizeof(ExternControl), 3, ReceivedBytes);
372	RemoteButtons \|= ExternControl.RemoteButtons;	381	RemoteButtons \|= ExternControl.RemoteButtons;
373	ConfirmFrame = ExternControl.Frame;	382	ConfirmFrame = ExternControl.Frame;
374	PcAccess = 255;	383	PcAccess = 255;
375	break;	384	break;
376	case 'c': // extern control with debug request	385	case 'c': // extern control with debug request
377	Decode64((uint8_t *) &ExternControl,sizeof(ExternControl),3,ReceivedBytes);	386	Decode64((uint8_t *) &ExternControl,sizeof(ExternControl),3,ReceivedBytes);
378	RemoteButtons \|= ExternControl.RemoteButtons;	387	RemoteButtons \|= ExternControl.RemoteButtons;
379	ConfirmFrame = ExternControl.Frame;	388	ConfirmFrame = ExternControl.Frame;
380	RequestDebugData = TRUE;	389	RequestDebugData = TRUE;
381	PcAccess = 255;	390	PcAccess = 255;
382	break;	391	break;
383	case 'h':// x-1 display columns	392	case 'h':// x-1 display columns
384	Decode64((uint8_t *) &tmp_char_arr2[0],sizeof(tmp_char_arr2),3,ReceivedBytes);	393	Decode64((uint8_t *) &tmp_char_arr2[0],sizeof(tmp_char_arr2),3,ReceivedBytes);
385	RemoteButtons \|= tmp_char_arr2[0];	394	RemoteButtons \|= tmp_char_arr2[0];
386	if(tmp_char_arr2[1] == 255) RequestChannelOnly = TRUE;	395	if(tmp_char_arr2[1] == 255) RequestChannelOnly = TRUE;
387	else RequestChannelOnly = FALSE; // keine Displaydaten	396	else RequestChannelOnly = FALSE; // keine Displaydaten
388	RequestDisplay = TRUE;	397	RequestDisplay = TRUE;
389	break;	398	break;
390	case 't':// motor test	399	case 't':// motor test
391	Decode64((uint8_t *) &MotorTest[0],sizeof(MotorTest),3,ReceivedBytes);	400	Decode64((uint8_t *) &MotorTest[0],sizeof(MotorTest),3,ReceivedBytes);
392	PcAccess = 255;	401	PcAccess = 255;
393	break;	402	break;
394	case 'k':// keys from DubWise	403	case 'k':// keys from DubWise
395	Decode64((uint8_t *) &DubWiseKeys[0],sizeof(DubWiseKeys),3,ReceivedBytes);	404	Decode64((uint8_t *) &DubWiseKeys[0],sizeof(DubWiseKeys),3,ReceivedBytes);
396	ConfirmFrame = DubWiseKeys[3];	405	ConfirmFrame = DubWiseKeys[3];
397	PcAccess = 255;	406	PcAccess = 255;
398	break;	407	break;
399	case 'v': // get version and board release	408	case 'v': // get version and board release
400	RequestVerInfo = TRUE;	409	RequestVerInfo = TRUE;
401	break;	410	break;
402	case 'g':// get external control data	411	case 'g':// get external control data
403	RequestExternalControl = TRUE;	412	RequestExternalControl = TRUE;
404	break;	413	break;
405	case 'q':// get settings	414	case 'q':// get settings
406	Decode64((uint8_t *) &tmp_char_arr2[0],sizeof(tmp_char_arr2),3,ReceivedBytes);	415	Decode64((uint8_t *) &tmp_char_arr2[0],sizeof(tmp_char_arr2),3,ReceivedBytes);
407	while(!txd_complete);	416	while(!txd_complete);
408	if(tmp_char_arr2[0] != 0xff)	417	if(tmp_char_arr2[0] != 0xff)
409	{	418	{
410	if(tmp_char_arr2[0] > 5) tmp_char_arr2[0] = 5; // limit to 5	419	if(tmp_char_arr2[0] > 5) tmp_char_arr2[0] = 5; // limit to 5
411	// load requested parameter set	420	// load requested parameter set
412	ParamSet_ReadFromEEProm(tmp_char_arr2[0]);	421	ParamSet_ReadFromEEProm(tmp_char_arr2[0]);
413	SendOutData('L' + tmp_char_arr2[0] -1,MySlaveAddr,(uint8_t *) &ParamSet.ChannelAssignment[0],PARAMSET_STRUCT_LEN);	422	SendOutData('L' + tmp_char_arr2[0] -1,MySlaveAddr,(uint8_t *) &ParamSet.ChannelAssignment[0],PARAMSET_STRUCT_LEN);
414	}	423	}
415	else // send active parameter set	424	else // send active parameter set
416	SendOutData('L' + GetParamByte(PID_ACTIVE_SET)-1,MySlaveAddr,(uint8_t *) &ParamSet.ChannelAssignment[0],PARAMSET_STRUCT_LEN);	425	SendOutData('L' + GetParamByte(PID_ACTIVE_SET)-1,MySlaveAddr,(uint8_t *) &ParamSet.ChannelAssignment[0],PARAMSET_STRUCT_LEN);
417		426
418	break;	427	break;
419		428
420	case 'l':	429	case 'l':
421	case 'm':	430	case 'm':
422	case 'n':	431	case 'n':
423	case 'o':	432	case 'o':
424	case 'p': // save parameterset	433	case 'p': // save parameterset
425	Decode64((uint8_t *) &ParamSet.ChannelAssignment[0],PARAMSET_STRUCT_LEN,3,ReceivedBytes);	434	Decode64((uint8_t *) &ParamSet.ChannelAssignment[0],PARAMSET_STRUCT_LEN,3,ReceivedBytes);
426	ParamSet_WriteToEEProm(rxd_buffer[2] - 'l' + 1);	435	ParamSet_WriteToEEProm(rxd_buffer[2] - 'l' + 1);
427	TurnOver180Nick = (int32_t) ParamSet.AngleTurnOverNick * 2500L;	436	TurnOver180Nick = (int32_t) ParamSet.AngleTurnOverNick * 2500L;
428	TurnOver180Roll = (int32_t) ParamSet.AngleTurnOverRoll * 2500L;	437	TurnOver180Roll = (int32_t) ParamSet.AngleTurnOverRoll * 2500L;
429	Beep(GetActiveParamSet());	438	Beep(GetActiveParamSet());
430	break;	439	break;
431		440
432		441
433	}	442	}
434	// unlock the rxd buffer after processing	443	// unlock the rxd buffer after processing
435	rxd_buffer_locked = FALSE;	444	rxd_buffer_locked = FALSE;
436	}	445	}
437		446
438	//############################################################################	447	//############################################################################
439	//Routine für die Serielle Ausgabe	448	//Routine für die Serielle Ausgabe
440	int16_t uart_putchar (int8_t c)	449	int16_t uart_putchar (int8_t c)
441	//############################################################################	450	//############################################################################
442	{	451	{
443	if (c == '\n')	452	if (c == '\n')
444	uart_putchar('\r');	453	uart_putchar('\r');
445	// wait until previous character was send	454	// wait until previous character was send
446	loop_until_bit_is_set(UCSR0A, UDRE0);	455	loop_until_bit_is_set(UCSR0A, UDRE0);
447	//Ausgabe des Zeichens	456	//Ausgabe des Zeichens
448	UDR0 = c;	457	UDR0 = c;
449	return (0);	458	return (0);
450	}	459	}
451		460
452		461
453	//---------------------------------------------------------------------------------------------	462	//---------------------------------------------------------------------------------------------
454	void USART0_TransmitTxData(void)	463	void USART0_TransmitTxData(void)
455	{	464	{
456	if(!txd_complete) return;	465	if(!txd_complete) return;
457		466
458	if(RequestExternalControl && txd_complete) // Bei Get werden die vom PC einstellbaren Werte vom PC zurückgelesen	467	if(RequestExternalControl && txd_complete) // Bei Get werden die vom PC einstellbaren Werte vom PC zurückgelesen
459	{	468	{
460	SendOutData('G',MySlaveAddr,(uint8_t *) &ExternControl,sizeof(ExternControl));	469	SendOutData('G',MySlaveAddr,(uint8_t *) &ExternControl,sizeof(ExternControl));
461	RequestExternalControl = FALSE;	470	RequestExternalControl = FALSE;
462	}	471	}
463		472
464	#ifdef USE_MK3MAG	473	#ifdef USE_MK3MAG
465	if((CheckDelay(Compass_Timer)) && txd_complete)	474	if((CheckDelay(Compass_Timer)) && txd_complete)
466	{	475	{
467	ToMk3Mag.Attitude[0] = (int16_t) (IntegralNick / 108); // approx. 0,1 Deg	476	ToMk3Mag.Attitude[0] = (int16_t) (IntegralNick / 108); // approx. 0,1 Deg
468	ToMk3Mag.Attitude[1] = (int16_t) (IntegralRoll / 108); // approx. 0,1 Deg	477	ToMk3Mag.Attitude[1] = (int16_t) (IntegralRoll / 108); // approx. 0,1 Deg
469	ToMk3Mag.UserParam[0] = FCParam.UserParam1;	478	ToMk3Mag.UserParam[0] = FCParam.UserParam1;
470	ToMk3Mag.UserParam[1] = FCParam.UserParam2;	479	ToMk3Mag.UserParam[1] = FCParam.UserParam2;
471	ToMk3Mag.CalState = CompassCalState;	480	ToMk3Mag.CalState = CompassCalState;
472	SendOutData('w',MySlaveAddr,(uint8_t *) &ToMk3Mag,sizeof(ToMk3Mag));	481	SendOutData('w',MySlaveAddr,(uint8_t *) &ToMk3Mag,sizeof(ToMk3Mag));
473	// the last state is 5 and should be send only once to avoid multiple flash writing	482	// the last state is 5 and should be send only once to avoid multiple flash writing
474	if(CompassCalState > 4) CompassCalState = 0;	483	if(CompassCalState > 4) CompassCalState = 0;
475	Compass_Timer = SetDelay(99);	484	Compass_Timer = SetDelay(99);
476	}	485	}
477	#endif	486	#endif
478		487
479	if((CheckDelay(Debug_Timer) \|\| RequestDebugData) && txd_complete)	488	if((CheckDelay(Debug_Timer) \|\| RequestDebugData) && txd_complete)
480	{	489	{
481	SendOutData('D',MySlaveAddr,(uint8_t *) &DebugOut,sizeof(DebugOut));	490	SendOutData('D',MySlaveAddr,(uint8_t *) &DebugOut,sizeof(DebugOut));
482	RequestDebugData = FALSE;	491	RequestDebugData = FALSE;
483	Debug_Timer = SetDelay(MIN_DEBUG_INTERVALL);	492	Debug_Timer = SetDelay(MIN_DEBUG_INTERVALL);
484	}	493	}
485		494
486	if(RequestDebugLabel != 255) // Texte für die Analogdaten	495	if(RequestDebugLabel != 255) // Texte für die Analogdaten
487	{	496	{
488	SendOutData('A',RequestDebugLabel + '0',(uint8_t *) ANALOG_LABEL[RequestDebugLabel],16);	497	SendOutData('A',RequestDebugLabel + '0',(uint8_t *) ANALOG_LABEL[RequestDebugLabel],16);
489	RequestDebugLabel = 255;	498	RequestDebugLabel = 255;
490	}	499	}
491	if(ConfirmFrame && txd_complete) // Datensatz ohne CRC bestätigen	500	if(ConfirmFrame && txd_complete) // Datensatz ohne CRC bestätigen

Subversion Repositories FlightCtrl

(root)/branches/V0.70d CRK HexaLotte/uart.c @ 2739 - Rev 942 → 943