0,0 → 1,192 |
#include "main.h" |
|
volatile unsigned int CountMilliseconds = 0; |
volatile static unsigned int tim_main; |
volatile unsigned char UpdateMotor = 0; |
volatile unsigned int cntKompass = 0; |
volatile unsigned int beeptime = 0; |
unsigned int BeepMuster = 0xffff; |
int ServoValue = 0; |
//Salvo 8.9.2007 |
volatile uint8_t Kompass_Neuer_Wert= 0; |
volatile unsigned int Kompass_Value_Old = 0; |
// Salvo End |
//Salvo 21.9.2007 |
short unsigned int Kompass_present= 0; //>0 bedeutet dass der Kompass vorhanden ist |
// Salvo End |
enum { |
STOP = 0, |
CK = 1, |
CK8 = 2, |
CK64 = 3, |
CK256 = 4, |
CK1024 = 5, |
T0_FALLING_EDGE = 6, |
T0_RISING_EDGE = 7 |
}; |
|
// Aenderungen von Peter Muehlenbrock ("Salvo") Stand 21.9.2007 |
/* |
Ersatzkompass abgeleitet aus Magnetkompass und Giergyro fuer nahezu neigungsubhaengige Kompassfunktion |
*/ |
SIGNAL (SIG_OVERFLOW0) // 8kHz |
{ |
static unsigned char cnt_1ms = 1,cnt = 0; |
unsigned char pieper_ein = 0; |
// TCNT0 -= 250;//TIMER_RELOAD_VALUE; |
|
if(!cnt--) |
{ |
if (Kompass_present > 0) Kompass_present--; //Runterzaehlen. Wenn 0 ist der Kompass nicht vorhanden |
cnt = 9; |
cnt_1ms++; |
cnt_1ms %= 2; |
if(!cnt_1ms) UpdateMotor = 1; |
CountMilliseconds++; |
} |
|
if(beeptime > 1) |
{ |
beeptime--; |
if(beeptime & BeepMuster) |
{ |
pieper_ein = 1; |
} |
else pieper_ein = 0; |
} |
else |
{ |
pieper_ein = 0; |
BeepMuster = 0xffff; |
} |
|
|
if(pieper_ein) |
{ |
if(PlatinenVersion == 10) PORTD |= (1<<2); // Speaker an PORTD.2 |
else PORTC |= (1<<7); // Speaker an PORTC.7 |
} |
else |
{ |
if(PlatinenVersion == 10) PORTD &= ~(1<<2); |
else PORTC &= ~(1<<7); |
} |
|
// if(EE_Parameter.GlobalConfig & CFG_KOMPASS_AKTIV) |
{ |
if(PINC & 0x10) |
{ |
cntKompass++; |
} |
else |
{ |
if((cntKompass) && (cntKompass < 4000)) |
{ |
// Salvo Kompassoffset 23.12.2007 *********** |
Kompass_present = 255; |
// Kompass_Value_Old = KompassValue; |
if (KOMPASS_OFFSET > 0) KompassValue = cntKompass -KOMPASS_OFFSET; |
else KompassValue = cntKompass - ((int) (Parameter_UserParam4*2)); |
|
if (KompassValue < 0) |
{ |
KompassValue += 360; |
} |
if (KompassValue >= 360) |
{ |
KompassValue -= 360; |
} |
// Salvo End |
} |
// if(cntKompass < 10) cntKompass = 10; |
// KompassValue = (unsigned long)((unsigned long)(cntKompass-10)*720L + 1L) / 703L; |
KompassRichtung = ((540 + KompassValue - KompassStartwert) % 360) - 180; |
//Salvo 13.9.2007 Ok Erkennung des Magnetkompasses |
Kompass_Neuer_Wert = 1; |
// Salvo End |
cntKompass = 0; |
} |
} |
} |
|
|
void Timer_Init(void) |
{ |
tim_main = SetDelay(10); |
TCCR0B = CK8; |
TCCR0A = (1<<COM0A1)|(1<<COM0B1)|3;//fast PWM |
OCR0A = 0; |
OCR0B = 120; |
TCNT0 = (unsigned char)-TIMER_RELOAD_VALUE; // reload |
//OCR1 = 0x00; |
|
TCCR2A=(1<<COM2A1)|(1<<COM2A0)|3; |
TCCR2B=(0<<CS20)|(1<<CS21)|(1<<CS22); |
|
// TIMSK2 |= _BV(TOIE2); |
TIMSK2 |= _BV(OCIE2A); |
|
TIMSK0 |= _BV(TOIE0); |
OCR2A = 10; |
TCNT2 = 0; |
|
} |
|
// ----------------------------------------------------------------------- |
|
unsigned int SetDelay (unsigned int t) |
{ |
// TIMSK0 &= ~_BV(TOIE0); |
return(CountMilliseconds + t + 1); |
// TIMSK0 |= _BV(TOIE0); |
} |
|
// ----------------------------------------------------------------------- |
char CheckDelay(unsigned int t) |
{ |
// TIMSK0 &= ~_BV(TOIE0); |
return(((t - CountMilliseconds) & 0x8000) >> 9); |
// TIMSK0 |= _BV(TOIE0); |
} |
|
// ----------------------------------------------------------------------- |
void Delay_ms(unsigned int w) |
{ |
unsigned int akt; |
akt = SetDelay(w); |
while (!CheckDelay(akt)); |
} |
|
void Delay_ms_Mess(unsigned int w) |
{ |
unsigned int akt; |
akt = SetDelay(w); |
while (!CheckDelay(akt)) ANALOG_ON; |
} |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Servo ansteuern |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
SIGNAL(SIG_OUTPUT_COMPARE2A) |
{ |
static unsigned char timer = 10; |
|
if(!timer--) |
{ |
TCCR2A=(1<<COM2A1)|(0<<COM2A0)|3; |
ServoValue = Parameter_ServoNickControl; |
if(EE_Parameter.ServoNickCompInvert & 0x01) ServoValue += ((long) EE_Parameter.ServoNickComp * (IntegralNick / 128)) / 512; |
else ServoValue -= ((long) EE_Parameter.ServoNickComp * (IntegralNick / 128)) / 512; |
|
if(ServoValue < EE_Parameter.ServoNickMin) ServoValue = EE_Parameter.ServoNickMin; |
else if(ServoValue > EE_Parameter.ServoNickMax) ServoValue = EE_Parameter.ServoNickMax; |
|
OCR2A = ServoValue;// + 75; |
timer = EE_Parameter.ServoNickRefresh; |
} |
else |
{ |
TCCR2A =3; |
PORTD&=~0x80; |
} |
} |