0,0 → 1,297 |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Copyright (c) 04.2007 Holger Buss |
// + Nur für den privaten Gebrauch |
// + www.MikroKopter.com |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Es gilt für das gesamte Projekt (Hardware, Software, Binärfiles, Sourcecode und Dokumentation), |
// + dass eine Nutzung (auch auszugsweise) nur für den privaten (nicht-kommerziellen) Gebrauch zulässig ist. |
// + Sollten direkte oder indirekte kommerzielle Absichten verfolgt werden, ist mit uns (info@mikrokopter.de) Kontakt |
// + bzgl. der Nutzungsbedingungen aufzunehmen. |
// + Eine kommerzielle Nutzung ist z.B.Verkauf von MikroKoptern, Bestückung und Verkauf von Platinen oder Bausätzen, |
// + Verkauf von Luftbildaufnahmen, usw. |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Werden Teile des Quellcodes (mit oder ohne Modifikation) weiterverwendet oder veröffentlicht, |
// + unterliegen sie auch diesen Nutzungsbedingungen und diese Nutzungsbedingungen incl. Copyright müssen dann beiliegen |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Sollte die Software (auch auszugesweise) oder sonstige Informationen des MikroKopter-Projekts |
// + auf anderen Webseiten oder sonstigen Medien veröffentlicht werden, muss unsere Webseite "http://www.mikrokopter.de" |
// + eindeutig als Ursprung verlinkt werden |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Keine Gewähr auf Fehlerfreiheit, Vollständigkeit oder Funktion |
// + Benutzung auf eigene Gefahr |
// + Wir übernehmen keinerlei Haftung für direkte oder indirekte Personen- oder Sachschäden |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Die Portierung der Software (oder Teile davon) auf andere Systeme (ausser der Hardware von www.mikrokopter.de) ist nur |
// + mit unserer Zustimmung zulässig |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Die Funktion printf_P() unterliegt ihrer eigenen Lizenz und ist hiervon nicht betroffen |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Redistributions of source code (with or without modifications) must retain the above copyright notice, |
// + this list of conditions and the following disclaimer. |
// + * Neither the name of the copyright holders nor the names of contributors may be used to endorse or promote products derived |
// + from this software without specific prior written permission. |
// + * The use of this project (hardware, software, binary files, sources and documentation) is only permittet |
// + for non-commercial use (directly or indirectly) |
// + Commercial use (for excample: selling of MikroKopters, selling of PCBs, assembly, ...) is only permitted |
// + with our written permission |
// + * If sources or documentations are redistributet on other webpages, out webpage (http://www.MikroKopter.de) must be |
// + clearly linked as origin |
// + * porting to systems other than hardware from www.mikrokopter.de is not allowed |
// + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
// + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
// + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE |
// + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE |
// + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR |
// + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF |
// + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS |
// + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN// + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) |
// + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE |
// + POSSIBILITY OF SUCH DAMAGE. |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
#include <stdlib.h> |
#include <inttypes.h> |
#include "eeprom.h" |
#include "timer2.h" |
#include "rc.h" |
#include "externalControl.h" |
#include "uart0.h" |
#include "printf_P.h" |
#include "analog.h" |
#include "twimaster.h" |
#include "attitude.h" |
|
#if (!defined (USE_NAVICTRL)) |
uint8_t MaxMenuItem = 13; |
#else |
#ifdef USE_NAVICTRL |
#include "gps.c" |
uint8_t MaxMenuItem = 14; |
#endif |
#endif |
uint8_t MenuItem = 0; |
uint8_t RemoteKeys = 0; |
|
#define KEY1 0x01 |
#define KEY2 0x02 |
#define KEY3 0x04 |
#define KEY4 0x08 |
#define KEY5 0x10 |
|
#define DISPLAYBUFFSIZE 80 |
int8_t DisplayBuff[DISPLAYBUFFSIZE] = "Hello World"; |
uint8_t DispPtr = 0; |
|
/************************************/ |
/* Clear LCD Buffer */ |
/************************************/ |
void LCD_Clear(void) { |
uint8_t i; |
for (i = 0; i < DISPLAYBUFFSIZE; i++) |
DisplayBuff[i] = ' '; |
} |
|
/************************************/ |
/* Update Menu on LCD */ |
/************************************/ |
// Display with 20 characters in 4 lines |
void LCD_PrintMenu(void) { |
if (RemoteKeys & KEY1) { |
if (MenuItem) |
MenuItem--; |
else |
MenuItem = MaxMenuItem; |
} |
|
if (RemoteKeys & KEY2) { |
if (MenuItem == MaxMenuItem) |
MenuItem = 0; |
else |
MenuItem++; |
} |
if ((RemoteKeys & KEY1) && (RemoteKeys & KEY2)) |
MenuItem = 0; |
|
LCD_Clear(); |
|
if (MenuItem > MaxMenuItem) |
MenuItem = MaxMenuItem; |
// print menu item number in the upper right corner |
if (MenuItem < 10) { |
LCD_printfxy(17,0,"[%i]",MenuItem); |
} else { |
LCD_printfxy(16,0,"[%i]",MenuItem); |
} |
|
switch (MenuItem) { |
case 0:// Version Info Menu Item |
LCD_printfxy(0,0,"+ MikroKopter +") |
; |
LCD_printfxy(0,1,"HW:V%d.%d SW:%d.%d%c",BoardRelease/10,BoardRelease%10,VERSION_MAJOR, VERSION_MINOR, VERSION_PATCH+'a') |
; |
LCD_printfxy(0,2,"Setting: %d %s", getActiveParamSet(), Mixer.Name) |
; |
if (I2CTimeout < 6) { |
LCD_printfxy(0,3,"I2C Error!!!"); |
} else if (missingMotor) { |
LCD_printfxy(0,3,"Missing BL-Ctrl:%d", missingMotor); |
} else LCD_printfxy(0,3,"(c) Holger Buss"); |
break; |
/* |
case 1:// Height Control Menu Item |
if(staticParams.GlobalConfig & CFG_HEIGHT_CONTROL) { |
LCD_printfxy(0,0,"Height: %5i",ReadingHeight); |
LCD_printfxy(0,1,"Set Point: %5i",SetPointHeight); |
LCD_printfxy(0,2,"Air Press.:%5i",0); |
LCD_printfxy(0,3,"Offset :%5i",0); |
} |
else |
{ |
LCD_printfxy(0,1,"No "); |
LCD_printfxy(0,2,"Height Control"); |
} |
break; |
*/ |
case 2:// Attitude Menu Item |
LCD_printfxy(0,0,"Attitude"); |
LCD_printfxy(0,1,"Nick: %5i", angle[PITCH] / GYRO_DEG_FACTOR_PITCHROLL); |
LCD_printfxy(0,2,"Roll: %5i", angle[ROLL ] / GYRO_DEG_FACTOR_PITCHROLL); |
LCD_printfxy(0,3,"Heading: %5i", compassHeading); |
break; |
case 3:// Remote Control Channel Menu Item |
LCD_printfxy(0,0,"C1:%4i C2:%4i ",PPM_in[1],PPM_in[2]); |
LCD_printfxy(0,1,"C3:%4i C4:%4i ",PPM_in[3],PPM_in[4]); |
LCD_printfxy(0,2,"C5:%4i C6:%4i ",PPM_in[5],PPM_in[6]); |
LCD_printfxy(0,3,"C7:%4i C8:%4i ",PPM_in[7],PPM_in[8]); |
break; |
case 4:// Remote Control Mapping Menu Item |
LCD_printfxy(0,0,"Ni:%4i Ro:%4i ",PPM_in[staticParams.ChannelAssignment[CH_PITCH]],PPM_in[staticParams.ChannelAssignment[CH_ROLL]]); |
LCD_printfxy(0,1,"Gs:%4i Ya:%4i ",PPM_in[staticParams.ChannelAssignment[CH_THROTTLE]],PPM_in[staticParams.ChannelAssignment[CH_YAW]]); |
LCD_printfxy(0,2,"P1:%4i P2:%4i ",PPM_in[staticParams.ChannelAssignment[CH_POTS]],PPM_in[staticParams.ChannelAssignment[CH_POTS+1]]); |
LCD_printfxy(0,3,"P3:%4i P4:%4i ",PPM_in[staticParams.ChannelAssignment[CH_POTS+2]],PPM_in[staticParams.ChannelAssignment[CH_POTS+3]]); |
break; |
/* |
case 5:// Gyro Sensor Menu Item |
LCD_printfxy(0,0,"Gyro - Sensor"); |
switch(BoardRelease) { |
case 10: |
LCD_printfxy(0,1,"Nick %4i (%3i.%i)", AdValueGyroNick - HiResNickOffset / HIRES_GYRO_AMPLIFY, HiResNickOffset / HIRES_GYRO_AMPLIFY, HiResNickOffset % HIRES_GYRO_AMPLIFY); |
LCD_printfxy(0,2,"Roll %4i (%3i.%i)", AdValueGyroRoll - HiResRollOffset / HIRES_GYRO_AMPLIFY, HiResRollOffset / HIRES_GYRO_AMPLIFY, HiResRollOffset % HIRES_GYRO_AMPLIFY); |
LCD_printfxy(0,3,"Yaw %4i (%3i)", AdValueGyroYaw , YawOffset); |
break; |
case 11: |
case 12: |
case 20: // divice Offests by 2 becuse 2 samples are added in adc isr |
LCD_printfxy(0,1,"Nick %4i (%3i.%i)",0, HiResNickOffset / (HIRES_GYRO_AMPLIFY * 2), (HiResNickOffset % (HIRES_GYRO_AMPLIFY * 2)) / 2); // division by 2 to push the reminder below 10 (15/2 = 7) |
LCD_printfxy(0,2,"Roll %4i (%3i.%i)",0, HiResRollOffset / (HIRES_GYRO_AMPLIFY * 2), (HiResRollOffset % (HIRES_GYRO_AMPLIFY * 2)) / 2); // division by 2 to push the reminder below 10 (15/2 = 7) |
LCD_printfxy(0,3,"Yaw %4i (%3i)",YawOffset - AdValueGyroYaw , YawOffset/2); |
break; |
|
case 13: |
default: // divice Offests by 2 becuse 2 samples are added in adc isr |
LCD_printfxy(0,1,"Nick %4i (%3i.%i)(%3i)",0, HiResNickOffset / (HIRES_GYRO_AMPLIFY * 2), (HiResNickOffset % (HIRES_GYRO_AMPLIFY * 2))/2, 0); // division by 2 to push the reminder below 10 (15/2 = 7) |
LCD_printfxy(0,2,"Roll %4i (%3i.%i)(%3i)",0, HiResRollOffset / (HIRES_GYRO_AMPLIFY * 2), (HiResRollOffset % (HIRES_GYRO_AMPLIFY * 2))/2, 0); // division by 2 to push the reminder below 10 (15/2 = 7) |
LCD_printfxy(0,3,"Yaw %4i (%3i)(%3i)",YawOffset - AdValueGyroYaw , YawOffset/2, 0); |
break; |
} |
break; |
case 6:// Acceleration Sensor Menu Item |
LCD_printfxy(0,0,"ACC - Sensor"); |
LCD_printfxy(0,1,"Nick %4i (%3i)",0,0); // factor 2 because of adding 2 samples in ADC ISR |
LCD_printfxy(0,2,"Roll %4i (%3i)",0,0); // factor 2 because of adding 2 samples in ADC ISR |
LCD_printfxy(0,3,"Height %4i (%3i)",0,0); |
break; |
*/ |
case 7:// Battery Voltage / Remote Control Level |
LCD_printfxy(0,1,"Voltage: %3i.%1iV",UBat/10, UBat%10); |
LCD_printfxy(0,2,"RC-Level: %5i",RC_Quality); |
break; |
case 8:// Compass Menu Item |
LCD_printfxy(0,0,"Compass "); |
LCD_printfxy(0,1,"Course: %5i", compassCourse); |
LCD_printfxy(0,2,"Heading: %5i", compassHeading); |
LCD_printfxy(0,3,"OffCourse: %5i", ((540 + compassHeading - compassCourse) % 360) - 180); |
break; |
case 9:// Poti Menu Item |
LCD_printfxy(0,0,"Po1: %3i Po5: %3i" ,variables[0], variables[4]); //PPM24-Extesion |
LCD_printfxy(0,1,"Po2: %3i Po6: %3i" ,variables[1], variables[5]); //PPM24-Extesion |
LCD_printfxy(0,2,"Po3: %3i Po7: %3i" ,variables[2], variables[6]); //PPM24-Extesion |
LCD_printfxy(0,3,"Po4: %3i Po8: %3i" ,variables[3], variables[7]); //PPM24-Extesion |
break; |
/* |
case 10:// Servo Menu Item |
LCD_printfxy(0,0,"Servo " ); |
LCD_printfxy(0,1,"Setpoint %3i",dynamicParams.ServoNickControl); |
LCD_printfxy(0,2,"Position: %3i",ServoNickValue); |
LCD_printfxy(0,3,"Range:%3i-%3i",staticParams.ServoNickMin, staticParams.ServoNickMax); |
break; |
*/ |
case 11://Extern Control |
LCD_printfxy(0,0,"ExternControl " ); |
LCD_printfxy(0,1,"Ni:%4i Ro:%4i ", externalControl.pitch, externalControl.roll); |
LCD_printfxy(0,2,"Gs:%4i Ya:%4i ", externalControl.throttle, externalControl.yaw); |
LCD_printfxy(0,3,"Hi:%4i Cf:%4i ", externalControl.height, externalControl.config); |
break; |
|
case 12://BL Communication errors |
LCD_printfxy(0,0,"BL-Ctrl Errors " ); |
LCD_printfxy(0,1," %3d %3d %3d %3d ",motor[0].Error,motor[1].Error,motor[2].Error,motor[3].Error); |
LCD_printfxy(0,2," %3d %3d %3d %3d ",motor[4].Error,motor[5].Error,motor[6].Error,motor[7].Error); |
LCD_printfxy(0,3," %3d %3d %3d %3d ",motor[8].Error,motor[9].Error,motor[10].Error,motor[11].Error); |
break; |
|
case 13://BL Overview |
LCD_printfxy(0,0,"BL-Ctrl found " ); |
LCD_printfxy(0,1," %c %c %c %c ",motor[0].Present + '-',motor[1].Present + '-',motor[2].Present + '-',motor[3].Present + '-'); |
LCD_printfxy(0,2," %c %c %c %c ",motor[4].Present + '-',motor[5].Present + '-',motor[6].Present + '-',motor[7].Present + '-'); |
LCD_printfxy(0,3," %c - - - ",motor[8].Present + '-'); |
if (motor[9].Present) |
LCD_printfxy(4,3,"10"); |
if (motor[10].Present) |
LCD_printfxy(8,3,"11"); |
if (motor[11].Present) |
LCD_printfxy(12,3,"12"); |
break; |
|
#if (defined (USE_NAVICTRL)) |
case 14://GPS Lat/Lon coords |
if (GPSInfo.status == INVALID) { |
LCD_printfxy(0,0,"No GPS data!"); |
} else { |
switch (GPSInfo.satfix) |
{ |
case SATFIX_NONE: |
LCD_printfxy(0,0,"Sats: %d Fix: No", GPSInfo.satnum); |
break; |
case SATFIX_2D: |
LCD_printfxy(0,0,"Sats: %d Fix: 2D", GPSInfo.satnum); |
break; |
case SATFIX_3D: |
LCD_printfxy(0,0,"Sats: %d Fix: 3D", GPSInfo.satnum); |
break; |
default: |
LCD_printfxy(0,0,"Sats: %d Fix: ??", GPSInfo.satnum); |
break; |
} |
int16_t i1,i2,i3; |
i1 = (int16_t)(GPSInfo.longitude/10000000L); |
i2 = abs((int16_t)((GPSInfo.longitude%10000000L)/10000L)); |
i3 = abs((int16_t)(((GPSInfo.longitude%10000000L)%10000L)/10L)); |
LCD_printfxy(0,1,"Lon: %d.%03d%03d deg",i1, i2, i3); |
i1 = (int16_t)(GPSInfo.latitude/10000000L); |
i2 = abs((int16_t)((GPSInfo.latitude%10000000L)/10000L)); |
i3 = abs((int16_t)(((GPSInfo.latitude%10000000L)%10000L)/10L)); |
LCD_printfxy(0,2,"Lat: %d.%03d%03d deg",i1, i2, i3); |
i1 = (int16_t)(GPSInfo.altitude/1000L); |
i2 = abs((int16_t)(GPSInfo.altitude%1000L)); |
LCD_printfxy(0,3,"Alt: %d.%03d m",i1, i2); |
} |
break; |
#endif |
|
default: |
MaxMenuItem = MenuItem - 1; |
MenuItem = 0; |
break; |
} |
RemoteKeys = 0; |
} |