0,0 → 1,1884 |
/*####################################################################################### |
Flight Control |
#######################################################################################*/ |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Copyright (c) Holger Buss, Ingo Busker |
// + Nur für den privaten Gebrauch / NON-COMMERCIAL USE ONLY |
// + www.MikroKopter.com |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Es gilt für das gesamte Projekt (Hardware, Software, Binärfiles, Sourcecode und Dokumentation), |
// + dass eine Nutzung (auch auszugsweise) nur für den privaten (nicht-kommerziellen) Gebrauch zulässig ist. |
// + Sollten direkte oder indirekte kommerzielle Absichten verfolgt werden, ist mit uns (info@mikrokopter.de) Kontakt |
// + bzgl. der Nutzungsbedingungen aufzunehmen. |
// + Eine kommerzielle Nutzung ist z.B.Verkauf von MikroKoptern, Bestückung und Verkauf von Platinen oder Bausätzen, |
// + Verkauf von Luftbildaufnahmen, usw. |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Werden Teile des Quellcodes (mit oder ohne Modifikation) weiterverwendet oder veröffentlicht, |
// + unterliegen sie auch diesen Nutzungsbedingungen und diese Nutzungsbedingungen incl. Copyright müssen dann beiliegen |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Sollte die Software (auch auszugesweise) oder sonstige Informationen des MikroKopter-Projekts |
// + auf anderen Webseiten oder sonstigen Medien veröffentlicht werden, muss unsere Webseite "http://www.mikrokopter.de" |
// + eindeutig als Ursprung verlinkt werden |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Keine Gewähr auf Fehlerfreiheit, Vollständigkeit oder Funktion |
// + Benutzung auf eigene Gefahr |
// + Wir übernehmen keinerlei Haftung für direkte oder indirekte Personen- oder Sachschäden |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Die Portierung oder Nutzung der Software (oder Teile davon) auf andere Systeme (ausser der Hardware von www.mikrokopter.de) ist nur |
// + mit unserer Zustimmung zulässig |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Die Funktion printf_P() unterliegt ihrer eigenen Lizenz und ist hiervon nicht betroffen |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Redistributions of source code (with or without modifications) must retain the above copyright notice, |
// + this list of conditions and the following disclaimer. |
// + * Neither the name of the copyright holders nor the names of contributors may be used to endorse or promote products derived |
// + from this software without specific prior written permission. |
// + * The use of this project (hardware, software, binary files, sources and documentation) is only permittet |
// + for non-commercial use (directly or indirectly) |
// + Commercial use (for excample: selling of MikroKopters, selling of PCBs, assembly, ...) is only permitted |
// + with our written permission |
// + * If sources or documentations are redistributet on other webpages, out webpage (http://www.MikroKopter.de) must be |
// + clearly linked as origin |
// + * porting the sources to other systems or using the software on other systems (except hardware from www.mikrokopter.de) is not allowed |
// + THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
// + AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
// + IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE |
// + ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE |
// + LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR |
// + CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF |
// + SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS |
// + INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN |
// + CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) |
// + ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE |
// + POSSIBILITY OF SUCH DAMAGE. |
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
|
#include "main.h" |
#include "mymath.h" |
#include "isqrt.h" |
|
|
//MartinW; added vars |
unsigned char loop1, loop2, loop3; |
unsigned char settingdest = 5; |
int keynumber=-7; |
|
unsigned short CurrentOffset = 0;/// |
|
unsigned char pos1, pos2, pos3, pos4=0; |
unsigned char Motors0,Motors1,Motors2,Motors3,Motors4,Motors5,Motors6,Motors7; |
unsigned char Motors0max,Motors1max,Motors2max,Motors3max,Motors4max,Motors5max,Motors6max,Motors7max; |
unsigned short MotorsTmax; |
unsigned char updatemotors=5; |
|
//Panorama Trigger; |
int degreeold =0; |
int degreedivold =0; |
int degreediv =0; |
unsigned int panograd=0; |
unsigned char panotrigger=0; |
unsigned char calibration_done = 0; |
///MartinW; added vars END |
|
|
|
unsigned char h,m,s; |
unsigned int BaroExpandActive = 0; |
int MesswertNick,MesswertRoll,MesswertGier,MesswertGierBias, RohMesswertNick,RohMesswertRoll; |
int TrimNick, TrimRoll; |
int AdNeutralNick = 0,AdNeutralRoll = 0,AdNeutralGier = 0,StartNeutralRoll = 0,StartNeutralNick = 0; |
int Mittelwert_AccNick, Mittelwert_AccRoll; |
unsigned int NeutralAccX=0, NeutralAccY=0; |
int NaviAccNick, NaviAccRoll,NaviCntAcc = 0; |
int NeutralAccZ = 0; |
unsigned char ControlHeading = 0;// in 2° |
long IntegralNick = 0,IntegralNick2 = 0; |
long IntegralRoll = 0,IntegralRoll2 = 0; |
long IntegralAccNick = 0,IntegralAccRoll = 0,IntegralAccZ = 0; |
long Integral_Gier = 0; |
long Mess_IntegralNick = 0,Mess_IntegralNick2 = 0; |
long Mess_IntegralRoll = 0,Mess_IntegralRoll2 = 0; |
//long Mess_Integral_Gier = 0,Mess_Integral_Gier2 = 0; ///MartinW so war es |
long Mess_Integral_Gier = 0; ///MartinW: Mess_Integral_Gier2 unbenutzt |
|
long MittelIntegralNick,MittelIntegralRoll,MittelIntegralNick2,MittelIntegralRoll2; |
long SummeNick=0,SummeRoll=0; |
volatile long Mess_Integral_Hoch = 0; |
int KompassValue = -1; |
int KompassSollWert = 0; |
int KompassRichtung = 0; |
char CalculateCompassTimer = 100; |
unsigned char KompassFusion = 32; |
unsigned int KompassSignalSchlecht = 50; |
unsigned char MAX_GAS,MIN_GAS; |
unsigned char HoehenReglerAktiv = 0; |
unsigned char TrichterFlug = 0; |
long Umschlag180Nick = 250000L, Umschlag180Roll = 250000L; |
long ErsatzKompass; |
int ErsatzKompassInGrad; // Kompasswert in Grad |
int GierGyroFehler = 0; |
char GyroFaktor,GyroFaktorGier; |
char IntegralFaktor,IntegralFaktorGier; |
int DiffNick,DiffRoll; |
//int Poti1 = 0, Poti2 = 0, Poti3 = 0, Poti4 = 0, Poti5 = 0, Poti6 = 0, Poti7 = 0, Poti8 = 0; |
unsigned char Poti[9] = {0,0,0,0,0,0,0,0}; |
volatile unsigned char SenderOkay = 0; |
int StickNick = 0,StickRoll = 0,StickGier = 0,StickGas = 0; |
char MotorenEin = 0,StartTrigger = 0; |
long HoehenWert = 0; |
long SollHoehe = 0; |
long FromNC_AltitudeSetpoint = 0; |
unsigned char FromNC_AltitudeSpeed = 0; |
unsigned char carefree_old = 50; // to make the Beep when switching |
|
int CompassGierSetpoint = 0; |
int LageKorrekturRoll = 0,LageKorrekturNick = 0, HoverGas = 0; |
//float Ki = FAKTOR_I; |
int Ki = 10300 / 33; |
unsigned char Looping_Nick = 0,Looping_Roll = 0; |
unsigned char Looping_Links = 0, Looping_Rechts = 0, Looping_Unten = 0, Looping_Oben = 0; |
|
unsigned char Parameter_Luftdruck_D = 48; // Wert : 0-250 |
unsigned char Parameter_MaxHoehe = 251; // Wert : 0-250 |
unsigned char Parameter_Hoehe_P = 16; // Wert : 0-32 |
unsigned char Parameter_Hoehe_ACC_Wirkung = 58; // Wert : 0-250 |
unsigned char Parameter_KompassWirkung = 64; // Wert : 0-250 |
unsigned char Parameter_Hoehe_GPS_Z = 64; // Wert : 0-250 |
unsigned char Parameter_Gyro_D = 8; // Wert : 0-250 |
unsigned char Parameter_Gyro_P = 150; // Wert : 10-250 |
unsigned char Parameter_Gyro_I = 150; // Wert : 0-250 |
unsigned char Parameter_Gyro_Gier_P = 150; // Wert : 10-250 |
unsigned char Parameter_Gyro_Gier_I = 150; // Wert : 10-250 |
unsigned char Parameter_Gier_P = 2; // Wert : 1-20 |
unsigned char Parameter_I_Faktor = 10; // Wert : 1-20 |
unsigned char Parameter_UserParam1 = 0; |
unsigned char Parameter_UserParam2 = 0; |
unsigned char Parameter_UserParam3 = 0; |
unsigned char Parameter_UserParam4 = 0; |
unsigned char Parameter_UserParam5 = 0; |
unsigned char Parameter_UserParam6 = 0; |
unsigned char Parameter_UserParam7 = 0; |
unsigned char Parameter_UserParam8 = 0; |
unsigned char Parameter_ServoNickControl = 100; |
unsigned char Parameter_ServoRollControl = 100; |
unsigned char Parameter_LoopGasLimit = 70; |
unsigned char Parameter_AchsKopplung1 = 90; |
unsigned char Parameter_AchsKopplung2 = 65; |
unsigned char Parameter_CouplingYawCorrection = 64; |
//unsigned char Parameter_AchsGegenKopplung1 = 0; |
unsigned char Parameter_DynamicStability = 100; |
unsigned char Parameter_J16Bitmask; // for the J16 Output |
unsigned char Parameter_J16Timing; // for the J16 Output |
unsigned char Parameter_J17Bitmask; // for the J17 Output |
unsigned char Parameter_J17Timing; // for the J17 Output |
unsigned char Parameter_NaviGpsModeControl; // Parameters for the Naviboard |
unsigned char Parameter_NaviGpsGain; |
unsigned char Parameter_NaviGpsP; |
unsigned char Parameter_NaviGpsI; |
unsigned char Parameter_NaviGpsD; |
unsigned char Parameter_NaviGpsACC; |
unsigned char Parameter_NaviOperatingRadius; |
unsigned char Parameter_NaviWindCorrection; |
unsigned char Parameter_NaviSpeedCompensation; |
unsigned char Parameter_ExternalControl; |
unsigned char Parameter_Servo3,Parameter_Servo4,Parameter_Servo5; |
unsigned char CareFree = 0; |
const signed char sintab[31] = { 0, 2, 4, 6, 7, 8, 8, 8, 7, 6, 4, 2, 0, -2, -4, -6, -7, -8, -8, -8, -7, -6, -4, -2, 0, 2, 4, 6, 7, 8, 8}; // 15° steps |
|
signed int ExternStickNick = 0,ExternStickRoll = 0,ExternStickGier = 0, ExternHoehenValue = -20; |
int MaxStickNick = 0,MaxStickRoll = 0; |
unsigned int modell_fliegt = 0; |
volatile unsigned char FC_StatusFlags = 0, FC_StatusFlags2 = 0; |
long GIER_GRAD_FAKTOR = 1291; |
signed int KopplungsteilNickRoll,KopplungsteilRollNick; |
signed int tmp_motorwert[MAX_MOTORS]; |
char VarioCharacter = ' '; |
|
#define LIMIT_MIN(value, min) {if(value <= min) value = min;} |
#define LIMIT_MAX(value, max) {if(value >= max) value = max;} |
#define LIMIT_MIN_MAX(value, min, max) {if(value <= min) value = min; else if(value >= max) value = max;} |
|
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Debugwerte zuordnen |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
void CopyDebugValues(void) |
{ |
DebugOut.Analog[0] = IntegralNick / (EE_Parameter.GyroAccFaktor * 4); |
DebugOut.Analog[1] = IntegralRoll / (EE_Parameter.GyroAccFaktor * 4); |
DebugOut.Analog[2] = Mittelwert_AccNick / 4; |
DebugOut.Analog[3] = Mittelwert_AccRoll / 4; |
DebugOut.Analog[4] = (signed int) AdNeutralGier - AdWertGier; |
DebugOut.Analog[5] = HoehenWert/5; |
DebugOut.Analog[6] = AdWertAccHoch;//(Mess_Integral_Hoch / 512);// Aktuell_az; |
DebugOut.Analog[8] = KompassValue; |
DebugOut.Analog[9] = UBat; |
DebugOut.Analog[10] = SenderOkay; |
DebugOut.Analog[11] = ErsatzKompass / GIER_GRAD_FAKTOR; |
DebugOut.Analog[12] = Motor[0].SetPoint; |
DebugOut.Analog[13] = Motor[1].SetPoint; |
DebugOut.Analog[14] = Motor[2].SetPoint; |
DebugOut.Analog[15] = Motor[3].SetPoint; |
|
///MartinW added Debug ouputs |
DebugOut.Analog[16] = Motor[4].SetPoint; |
DebugOut.Analog[17] = Motor[5].SetPoint; |
|
DebugOut.Analog[18] = FromNC_AltitudeSpeed; /// |
|
//DebugOut.Analog[18] = Motor[6].SetPoint; // v0.84a |
//DebugOut.Analog[24] = Motor[6].SetPoint; // on v0.84a = SollHoehe/5 |
DebugOut.Analog[25] = Motor[6].SetPoint; |
DebugOut.Analog[26] = Motor[7].SetPoint; |
//DebugOut.Analog[27] = Motor[9].SetPoint; // on v0.84a = KompassSollWert |
///MartinW added Debug ouputs END |
|
DebugOut.Analog[20] = ServoNickValue; |
DebugOut.Analog[22] = Capacity.ActualCurrent; |
DebugOut.Analog[23] = Capacity.UsedCapacity; |
DebugOut.Analog[24] = SollHoehe/5; |
// DebugOut.Analog[22] = FromNaviCtrl_Value.GpsZ; |
// DebugOut.Analog[29] = FromNaviCtrl_Value.SerialDataOkay; |
DebugOut.Analog[27] = KompassSollWert; |
DebugOut.Analog[29] = Capacity.MinOfMaxPWM; |
DebugOut.Analog[30] = GPS_Nick; |
DebugOut.Analog[31] = GPS_Roll; |
|
|
if(VersionInfo.HardwareError[0] || VersionInfo.HardwareError[1]) DebugOut.Status[1] |= 1; else DebugOut.Status[1] &= 0xfe; |
} |
|
|
|
void Piep(unsigned char Anzahl, unsigned int dauer) |
{ |
if(MotorenEin) return; //auf keinen Fall im Flug! |
while(Anzahl--) |
{ |
beeptime = dauer; |
while(beeptime); |
Delay_ms(dauer * 2); |
} |
} |
|
//############################################################################ |
// Messwerte beim Ermitteln der Nullage |
void CalibrierMittelwert(void) |
//############################################################################ |
{ |
unsigned char i; |
if(PlatinenVersion == 13) SucheGyroOffset(); |
// ADC auschalten, damit die Werte sich nicht während der Berechnung ändern |
ANALOG_OFF; |
MesswertNick = AdWertNick; |
MesswertRoll = AdWertRoll; |
MesswertGier = AdWertGier; |
Mittelwert_AccNick = ACC_AMPLIFY * AdWertAccNick; |
Mittelwert_AccRoll = ACC_AMPLIFY * AdWertAccRoll; |
// ADC einschalten |
ANALOG_ON; |
for(i=0;i<8;i++) |
{ |
int tmp; |
tmp = PPM_in[EE_Parameter.Kanalbelegung[K_POTI1 + i]] + 127; |
LIMIT_MIN_MAX(tmp, 0, 255); |
if(Poti[i] > tmp) Poti[i]--; else if(Poti[i] < tmp) Poti[i]++; |
} |
Umschlag180Nick = (long) EE_Parameter.WinkelUmschlagNick * 2500L; |
Umschlag180Roll = (long) EE_Parameter.WinkelUmschlagRoll * 2500L; |
} |
|
//############################################################################ |
// Nullwerte ermitteln |
void SetNeutral(unsigned char AccAdjustment) |
//############################################################################ |
{ |
unsigned char i; |
unsigned int gier_neutral=0, nick_neutral=0, roll_neutral=0; |
VersionInfo.HardwareError[0] = 0; |
HEF4017R_ON; |
NeutralAccX = 0; |
NeutralAccY = 0; |
NeutralAccZ = 0; |
|
AdNeutralNick = 0; |
AdNeutralRoll = 0; |
AdNeutralGier = 0; |
|
Parameter_AchsKopplung1 = 0; |
Parameter_AchsKopplung2 = 0; |
|
ExpandBaro = 0; |
|
CalibrierMittelwert(); |
Delay_ms_Mess(100); |
|
CalibrierMittelwert(); |
|
if((EE_Parameter.GlobalConfig & CFG_HOEHENREGELUNG)) // Höhenregelung aktiviert? |
{ |
if((MessLuftdruck > 950) || (MessLuftdruck < 750)) SucheLuftruckOffset(); |
} |
#define NEUTRAL_FILTER 32 |
for(i=0; i<NEUTRAL_FILTER; i++) |
{ |
Delay_ms_Mess(10); |
gier_neutral += AdWertGier; |
nick_neutral += AdWertNick; |
roll_neutral += AdWertRoll; |
} |
AdNeutralNick= (nick_neutral+NEUTRAL_FILTER/2) / (NEUTRAL_FILTER / 8); |
AdNeutralRoll= (roll_neutral+NEUTRAL_FILTER/2) / (NEUTRAL_FILTER / 8); |
AdNeutralGier= (gier_neutral+NEUTRAL_FILTER/2) / (NEUTRAL_FILTER); |
|
StartNeutralRoll = AdNeutralRoll; |
StartNeutralNick = AdNeutralNick; |
|
if(AccAdjustment) |
{ |
NeutralAccX = abs(Mittelwert_AccNick) / (2*ACC_AMPLIFY); |
NeutralAccY = abs(Mittelwert_AccRoll) / (2*ACC_AMPLIFY); |
NeutralAccZ = Aktuell_az; |
|
// Save ACC neutral settings to eeprom |
SetParamWord(PID_ACC_NICK, (uint16_t)NeutralAccX); |
SetParamWord(PID_ACC_ROLL, (uint16_t)NeutralAccY); |
SetParamWord(PID_ACC_TOP, (uint16_t)NeutralAccZ); |
} |
else |
{ |
// restore from eeprom |
NeutralAccX = (int16_t)GetParamWord(PID_ACC_NICK); |
NeutralAccY = (int16_t)GetParamWord(PID_ACC_ROLL); |
NeutralAccZ = (int16_t)GetParamWord(PID_ACC_TOP); |
// strange settings? |
if(((unsigned int) NeutralAccX > 2048) || ((unsigned int) NeutralAccY > 2048) || ((unsigned int) NeutralAccZ > 1024)) |
{ |
printf("\n\rACC not calibrated!\r\n"); |
NeutralAccX = abs(Mittelwert_AccNick) / (2*ACC_AMPLIFY); |
NeutralAccY = abs(Mittelwert_AccRoll) / (2*ACC_AMPLIFY); |
NeutralAccZ = Aktuell_az; |
} |
} |
|
MesswertNick = 0; |
MesswertRoll = 0; |
MesswertGier = 0; |
Delay_ms_Mess(100); |
Mittelwert_AccNick = ACC_AMPLIFY * AdWertAccNick; |
Mittelwert_AccRoll = ACC_AMPLIFY * AdWertAccRoll; |
IntegralNick = EE_Parameter.GyroAccFaktor * (long)Mittelwert_AccNick; |
IntegralRoll = EE_Parameter.GyroAccFaktor * (long)Mittelwert_AccRoll; |
Mess_IntegralNick2 = IntegralNick; |
Mess_IntegralRoll2 = IntegralRoll; |
Mess_Integral_Gier = 0; |
StartLuftdruck = Luftdruck; |
VarioMeter = 0; |
Mess_Integral_Hoch = 0; |
KompassSollWert = KompassValue; |
KompassSignalSchlecht = 100; |
GPS_Neutral(); |
beeptime = 50; |
Umschlag180Nick = ((long) EE_Parameter.WinkelUmschlagNick * 2500L) + 15000L; |
Umschlag180Roll = ((long) EE_Parameter.WinkelUmschlagRoll * 2500L) + 15000L; |
ExternHoehenValue = 0; |
ErsatzKompass = KompassValue * GIER_GRAD_FAKTOR; |
GierGyroFehler = 0; |
SendVersionToNavi = 1; |
LED_Init(); |
FC_StatusFlags |= FC_STATUS_CALIBRATE; |
FromNaviCtrl_Value.Kalman_K = -1; |
FromNaviCtrl_Value.Kalman_MaxDrift = 0; |
FromNaviCtrl_Value.Kalman_MaxFusion = 32; |
for(i=0;i<8;i++) |
{ |
Poti[i] = PPM_in[EE_Parameter.Kanalbelegung[K_POTI1 + i]] + 127; |
} |
SenderOkay = 100; |
if(ServoActive) |
{ |
HEF4017R_ON; |
DDRD |=0x80; // enable J7 -> Servo signal |
} |
|
if((AdNeutralNick < 150 * 16) || (AdNeutralNick > 850 * 16)) { VersionInfo.HardwareError[0] |= FC_ERROR0_GYRO_NICK; }; |
if((AdNeutralRoll < 150 * 16) || (AdNeutralRoll > 850 * 16)) { VersionInfo.HardwareError[0] |= FC_ERROR0_GYRO_ROLL; }; |
if((AdNeutralGier < 150 * 2) || (AdNeutralGier > 850 * 2)) { VersionInfo.HardwareError[0] |= FC_ERROR0_GYRO_YAW; }; |
if((NeutralAccX < 300) || (NeutralAccX > 750)) { VersionInfo.HardwareError[0] |= FC_ERROR0_ACC_NICK; }; |
if((NeutralAccY < 300) || (NeutralAccY > 750)) { VersionInfo.HardwareError[0] |= FC_ERROR0_ACC_ROLL; }; |
if((NeutralAccZ < 512) || (NeutralAccZ > 850)) { VersionInfo.HardwareError[0] |= FC_ERROR0_ACC_TOP; }; |
carefree_old = 70; |
} |
|
|
//############################################################################ |
// Bearbeitet die Messwerte |
void Mittelwert(void) |
//############################################################################ |
{ |
static signed long tmpl,tmpl2,tmpl3,tmpl4; |
static signed int oldNick, oldRoll, d2Roll, d2Nick; |
signed long winkel_nick, winkel_roll; |
MesswertGier = (signed int) AdNeutralGier - AdWertGier; |
MesswertNick = (signed int) AdWertNickFilter / 8; |
MesswertRoll = (signed int) AdWertRollFilter / 8; |
RohMesswertNick = MesswertNick; |
RohMesswertRoll = MesswertRoll; |
|
// Beschleunigungssensor ++++++++++++++++++++++++++++++++++++++++++++++++ |
Mittelwert_AccNick = (Mittelwert_AccNick * 3 + ((ACC_AMPLIFY * AdWertAccNick))) / 4L; |
Mittelwert_AccRoll = (Mittelwert_AccRoll * 3 + ((ACC_AMPLIFY * AdWertAccRoll))) / 4L; |
IntegralAccNick += ACC_AMPLIFY * AdWertAccNick; |
IntegralAccRoll += ACC_AMPLIFY * AdWertAccRoll; |
NaviAccNick += AdWertAccNick; |
NaviAccRoll += AdWertAccRoll; |
NaviCntAcc++; |
IntegralAccZ += Aktuell_az - NeutralAccZ; |
|
//++++++++++++++++++++++++++++++++++++++++++++++++ |
// ADC einschalten |
ANALOG_ON; |
AdReady = 0; |
//++++++++++++++++++++++++++++++++++++++++++++++++ |
|
if(Mess_IntegralRoll > 93000L) winkel_roll = 93000L; |
else if(Mess_IntegralRoll <-93000L) winkel_roll = -93000L; |
else winkel_roll = Mess_IntegralRoll; |
|
if(Mess_IntegralNick > 93000L) winkel_nick = 93000L; |
else if(Mess_IntegralNick <-93000L) winkel_nick = -93000L; |
else winkel_nick = Mess_IntegralNick; |
|
// Gier ++++++++++++++++++++++++++++++++++++++++++++++++ |
Mess_Integral_Gier += MesswertGier; |
ErsatzKompass += MesswertGier; |
// Kopplungsanteil +++++++++++++++++++++++++++++++++++++ |
if(!Looping_Nick && !Looping_Roll && (EE_Parameter.GlobalConfig & CFG_ACHSENKOPPLUNG_AKTIV)) |
{ |
tmpl3 = (MesswertRoll * winkel_nick) / 2048L; |
tmpl3 *= Parameter_AchsKopplung2; //65 |
tmpl3 /= 4096L; |
tmpl4 = (MesswertNick * winkel_roll) / 2048L; |
tmpl4 *= Parameter_AchsKopplung2; //65 |
tmpl4 /= 4096L; |
KopplungsteilNickRoll = tmpl3; |
KopplungsteilRollNick = tmpl4; |
tmpl4 -= tmpl3; |
ErsatzKompass += tmpl4; |
if(!Parameter_CouplingYawCorrection) Mess_Integral_Gier -= tmpl4/2; // Gier nachhelfen |
|
tmpl = ((MesswertGier + tmpl4) * winkel_nick) / 2048L; |
tmpl *= Parameter_AchsKopplung1; // 90 |
tmpl /= 4096L; |
tmpl2 = ((MesswertGier + tmpl4) * winkel_roll) / 2048L; |
tmpl2 *= Parameter_AchsKopplung1; |
tmpl2 /= 4096L; |
if(abs(MesswertGier) > 64) if(labs(tmpl) > 128 || labs(tmpl2) > 128) TrichterFlug = 1; |
//MesswertGier += (Parameter_CouplingYawCorrection * tmpl4) / 256; |
} |
else tmpl = tmpl2 = KopplungsteilNickRoll = KopplungsteilRollNick = 0; |
TrimRoll = tmpl - tmpl2 / 100L; |
TrimNick = -tmpl2 + tmpl / 100L; |
// Kompasswert begrenzen ++++++++++++++++++++++++++++++++++++++++++++++++ |
if(ErsatzKompass >= (360L * GIER_GRAD_FAKTOR)) ErsatzKompass -= 360L * GIER_GRAD_FAKTOR; // 360° Umschlag |
if(ErsatzKompass < 0) ErsatzKompass += 360L * GIER_GRAD_FAKTOR; |
// Roll ++++++++++++++++++++++++++++++++++++++++++++++++ |
Mess_IntegralRoll2 += MesswertRoll + TrimRoll; |
Mess_IntegralRoll += MesswertRoll + TrimRoll - LageKorrekturRoll; |
if(Mess_IntegralRoll > Umschlag180Roll) |
{ |
Mess_IntegralRoll = -(Umschlag180Roll - 25000L); |
Mess_IntegralRoll2 = Mess_IntegralRoll; |
} |
if(Mess_IntegralRoll <-Umschlag180Roll) |
{ |
Mess_IntegralRoll = (Umschlag180Roll - 25000L); |
Mess_IntegralRoll2 = Mess_IntegralRoll; |
} |
// Nick ++++++++++++++++++++++++++++++++++++++++++++++++ |
Mess_IntegralNick2 += MesswertNick + TrimNick; |
Mess_IntegralNick += MesswertNick + TrimNick - LageKorrekturNick; |
if(Mess_IntegralNick > Umschlag180Nick) |
{ |
Mess_IntegralNick = -(Umschlag180Nick - 25000L); |
Mess_IntegralNick2 = Mess_IntegralNick; |
} |
if(Mess_IntegralNick <-Umschlag180Nick) |
{ |
Mess_IntegralNick = (Umschlag180Nick - 25000L); |
Mess_IntegralNick2 = Mess_IntegralNick; |
} |
|
Integral_Gier = Mess_Integral_Gier; |
IntegralNick = Mess_IntegralNick; |
IntegralRoll = Mess_IntegralRoll; |
IntegralNick2 = Mess_IntegralNick2; |
IntegralRoll2 = Mess_IntegralRoll2; |
|
#define D_LIMIT 128 |
|
MesswertNick = HiResNick / 8; |
MesswertRoll = HiResRoll / 8; |
|
if(AdWertNick < 15) MesswertNick = -1000; if(AdWertNick < 7) MesswertNick = -2000; |
if(PlatinenVersion == 10) { if(AdWertNick > 1010) MesswertNick = +1000; if(AdWertNick > 1017) MesswertNick = +2000; } |
else { if(AdWertNick > 2000) MesswertNick = +1000; if(AdWertNick > 2015) MesswertNick = +2000; } |
if(AdWertRoll < 15) MesswertRoll = -1000; if(AdWertRoll < 7) MesswertRoll = -2000; |
if(PlatinenVersion == 10) { if(AdWertRoll > 1010) MesswertRoll = +1000; if(AdWertRoll > 1017) MesswertRoll = +2000; } |
else { if(AdWertRoll > 2000) MesswertRoll = +1000; if(AdWertRoll > 2015) MesswertRoll = +2000; } |
|
if(Parameter_Gyro_D) |
{ |
d2Nick = HiResNick - oldNick; |
oldNick = (oldNick + HiResNick)/2; |
if(d2Nick > D_LIMIT) d2Nick = D_LIMIT; |
else if(d2Nick < -D_LIMIT) d2Nick = -D_LIMIT; |
|
d2Roll = HiResRoll - oldRoll; |
oldRoll = (oldRoll + HiResRoll)/2; |
if(d2Roll > D_LIMIT) d2Roll = D_LIMIT; |
else if(d2Roll < -D_LIMIT) d2Roll = -D_LIMIT; |
|
MesswertNick += (d2Nick * (signed int) Parameter_Gyro_D) / 16; |
MesswertRoll += (d2Roll * (signed int) Parameter_Gyro_D) / 16; |
HiResNick += (d2Nick * (signed int) Parameter_Gyro_D); |
HiResRoll += (d2Roll * (signed int) Parameter_Gyro_D); |
} |
|
if(RohMesswertRoll > 0) TrimRoll += ((long) abs(KopplungsteilNickRoll) * Parameter_CouplingYawCorrection) / 64L; |
else TrimRoll -= ((long) abs(KopplungsteilNickRoll) * Parameter_CouplingYawCorrection) / 64L; |
if(RohMesswertNick > 0) TrimNick += ((long) abs(KopplungsteilRollNick) * Parameter_CouplingYawCorrection) / 64L; |
else TrimNick -= ((long) abs(KopplungsteilRollNick) * Parameter_CouplingYawCorrection) / 64L; |
|
if(EE_Parameter.GlobalConfig & CFG_DREHRATEN_BEGRENZER && !Looping_Nick && !Looping_Roll) |
{ |
if(RohMesswertNick > 256) MesswertNick += 1 * (RohMesswertNick - 256); |
else if(RohMesswertNick < -256) MesswertNick += 1 * (RohMesswertNick + 256); |
if(RohMesswertRoll > 256) MesswertRoll += 1 * (RohMesswertRoll - 256); |
else if(RohMesswertRoll < -256) MesswertRoll += 1 * (RohMesswertRoll + 256); |
} |
} |
|
//############################################################################ |
// Senden der Motorwerte per I2C-Bus |
void SendMotorData(void) |
//############################################################################ |
{ |
unsigned char i; |
if(!MotorenEin) |
{ |
FC_StatusFlags &= ~(FC_STATUS_MOTOR_RUN | FC_STATUS_FLY); |
for(i=0;i<MAX_MOTORS;i++) |
{ |
if(!PC_MotortestActive) MotorTest[i] = 0; |
Motor[i].SetPoint = MotorTest[i]; |
Motor[i].SetPointLowerBits = 0; |
/* |
Motor[i].SetPoint = MotorTest[i] / 4; // testing the high resolution |
Motor[i].SetPointLowerBits = MotorTest[i] % 4; |
*/ |
} |
if(PC_MotortestActive) PC_MotortestActive--; |
} |
else FC_StatusFlags |= FC_STATUS_MOTOR_RUN; |
|
if(I2C_TransferActive) |
{ |
I2C_TransferActive = 0; // enable for the next time |
} |
else |
{ |
motor_write = 0; |
I2C_Start(TWI_STATE_MOTOR_TX); //Start I2C Interrupt Mode |
} |
} |
|
|
|
//############################################################################ |
// Trägt ggf. das Poti als Parameter ein |
void ParameterZuordnung(void) |
//############################################################################ |
{ |
unsigned char tmp,i; |
#define CHK_POTI(b,a) {if(a < 248) b = a; else b = Poti[255 - a];} |
#define CHK_POTI_MM(b,a,min,max) {CHK_POTI(b,a); LIMIT_MIN_MAX(b, min, max);} |
for(i=0;i<8;i++) |
{ |
int tmp2; |
tmp2 = PPM_in[EE_Parameter.Kanalbelegung[K_POTI1 + i]] + 127; |
if(tmp2 > 255) tmp2 = 255; else if(tmp2 < 0) tmp2 = 0; |
if(tmp2 != Poti[i]) |
{ |
Poti[i] += (tmp2 - Poti[i]) / 4; |
if(Poti[i] > tmp2) Poti[i]--; |
else Poti[i]++; |
} |
} |
CHK_POTI_MM(Parameter_Luftdruck_D,EE_Parameter.Luftdruck_D,0,100); |
CHK_POTI_MM(Parameter_Hoehe_P,EE_Parameter.Hoehe_P,0,100); |
CHK_POTI_MM(Parameter_Gyro_P,EE_Parameter.Gyro_P,10,255); |
CHK_POTI_MM(Parameter_J16Timing,EE_Parameter.J16Timing,1,255); |
CHK_POTI_MM(Parameter_J17Timing,EE_Parameter.J17Timing,1,255); |
CHK_POTI(Parameter_Servo3,EE_Parameter.Servo3); |
CHK_POTI(Parameter_Servo4,EE_Parameter.Servo4); |
CHK_POTI(Parameter_Servo5,EE_Parameter.Servo5); |
CHK_POTI(Parameter_MaxHoehe,EE_Parameter.MaxHoehe); |
CHK_POTI(Parameter_MaxHoehe,EE_Parameter.MaxHoehe); |
CHK_POTI(Parameter_Hoehe_ACC_Wirkung,EE_Parameter.Hoehe_ACC_Wirkung); |
CHK_POTI(Parameter_Hoehe_GPS_Z,EE_Parameter.Hoehe_GPS_Z); |
CHK_POTI(Parameter_KompassWirkung,EE_Parameter.KompassWirkung); |
CHK_POTI(Parameter_Gyro_I,EE_Parameter.Gyro_I); |
CHK_POTI(Parameter_Gyro_D,EE_Parameter.Gyro_D); |
CHK_POTI(Parameter_Gyro_Gier_P,EE_Parameter.Gyro_Gier_P); |
CHK_POTI(Parameter_Gyro_Gier_I,EE_Parameter.Gyro_Gier_I); |
CHK_POTI(Parameter_I_Faktor,EE_Parameter.I_Faktor); |
CHK_POTI(Parameter_UserParam1,EE_Parameter.UserParam1); |
CHK_POTI(Parameter_UserParam2,EE_Parameter.UserParam2); |
CHK_POTI(Parameter_UserParam3,EE_Parameter.UserParam3); |
CHK_POTI(Parameter_UserParam4,EE_Parameter.UserParam4); |
CHK_POTI(Parameter_UserParam5,EE_Parameter.UserParam5); |
CHK_POTI(Parameter_UserParam6,EE_Parameter.UserParam6); |
CHK_POTI(Parameter_UserParam7,EE_Parameter.UserParam7); |
CHK_POTI(Parameter_UserParam8,EE_Parameter.UserParam8); |
CHK_POTI(Parameter_ServoNickControl,EE_Parameter.ServoNickControl); |
CHK_POTI(Parameter_ServoRollControl,EE_Parameter.ServoRollControl); |
CHK_POTI(Parameter_LoopGasLimit,EE_Parameter.LoopGasLimit); |
CHK_POTI(Parameter_AchsKopplung1,EE_Parameter.AchsKopplung1); |
CHK_POTI(Parameter_AchsKopplung2,EE_Parameter.AchsKopplung2); |
CHK_POTI(Parameter_CouplingYawCorrection,EE_Parameter.CouplingYawCorrection); |
// CHK_POTI(Parameter_AchsGegenKopplung1,EE_Parameter.AchsGegenKopplung1,0,255); |
CHK_POTI(Parameter_DynamicStability,EE_Parameter.DynamicStability); |
CHK_POTI(Parameter_ExternalControl,EE_Parameter.ExternalControl); |
Ki = 10300 / (Parameter_I_Faktor + 1); |
MAX_GAS = EE_Parameter.Gas_Max; |
MIN_GAS = EE_Parameter.Gas_Min; |
|
tmp = EE_Parameter.OrientationModeControl; |
if(tmp > 50) |
{ |
#ifdef SWITCH_LEARNS_CAREFREE |
if(!CareFree) ControlHeading = (((int) EE_Parameter.OrientationAngle * 15 + KompassValue) % 360) / 2; |
#endif |
CareFree = 1; |
if(tmp >= 248 && Poti[255 - tmp] < 50) CareFree = 0; |
if(carefree_old != CareFree) |
{ |
if(carefree_old < 3) |
{ |
if(CareFree) beeptime = 1500; |
else beeptime = 200; |
carefree_old = CareFree; |
} else carefree_old--; |
} |
if(FromNaviCtrl.CompassValue < 0 && CareFree) VersionInfo.HardwareError[0] |= FC_ERROR0_CAREFREE; else VersionInfo.HardwareError[0] &= ~FC_ERROR0_CAREFREE; |
} |
else |
{ |
CareFree = 0; |
carefree_old = 10; |
} |
|
if(FromNaviCtrl.CompassValue < 0 && MotorenEin && CareFree && BeepMuster == 0xffff) // ungültiger Kompasswert |
{ |
beeptime = 15000; |
BeepMuster = 0xA400; |
CareFree = 0; |
} |
if(CareFree) { FC_StatusFlags2 |= FC_STATUS2_CAREFREE; if(Parameter_AchsKopplung1 < 210) Parameter_AchsKopplung1 += 30;} else FC_StatusFlags2 &= ~FC_STATUS2_CAREFREE; |
} |
|
//############################################################################ |
// |
void MotorRegler(void) |
//############################################################################ |
{ |
int pd_ergebnis_nick,pd_ergebnis_roll,tmp_int, tmp_int2; |
int GierMischanteil,GasMischanteil; |
static long sollGier = 0,tmp_long,tmp_long2; |
static long IntegralFehlerNick = 0; |
static long IntegralFehlerRoll = 0; |
static unsigned int RcLostTimer; |
static unsigned char delay_neutral = 0; |
static unsigned char delay_einschalten = 0,delay_ausschalten = 0; |
//static unsigned char calibration_done = 0;// moved up |
static char NeueKompassRichtungMerken = 0; |
static long ausgleichNick, ausgleichRoll; |
int IntegralNickMalFaktor,IntegralRollMalFaktor; |
unsigned char i; |
Mittelwert(); |
GRN_ON; |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Gaswert ermitteln |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
GasMischanteil = StickGas; |
if(GasMischanteil < MIN_GAS + 10) GasMischanteil = MIN_GAS + 10; |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Empfang schlecht |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(SenderOkay < 100) |
{ |
if(RcLostTimer) RcLostTimer--; |
else |
{ |
MotorenEin = 0; |
FC_StatusFlags &= ~FC_STATUS_EMERGENCY_LANDING; |
} |
ROT_ON; |
if(modell_fliegt > 1000) // wahrscheinlich in der Luft --> langsam absenken |
{ |
GasMischanteil = EE_Parameter.NotGas; |
FC_StatusFlags |= FC_STATUS_EMERGENCY_LANDING; |
PPM_diff[EE_Parameter.Kanalbelegung[K_NICK]] = 0; |
PPM_diff[EE_Parameter.Kanalbelegung[K_ROLL]] = 0; |
PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] = 0; |
PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] = 0; |
PPM_in[EE_Parameter.Kanalbelegung[K_GIER]] = 0; |
} |
else MotorenEin = 0; |
} |
else |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Emfang gut |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(SenderOkay > 140) |
{ |
FC_StatusFlags &= ~FC_STATUS_EMERGENCY_LANDING; |
RcLostTimer = EE_Parameter.NotGasZeit * 50; |
if(GasMischanteil > 40 && MotorenEin) |
{ |
if(modell_fliegt < 0xffff) modell_fliegt++; |
} |
if((modell_fliegt < 256)) |
{ |
SummeNick = 0; |
SummeRoll = 0; |
sollGier = 0; |
Mess_Integral_Gier = 0; |
} else FC_StatusFlags |= FC_STATUS_FLY; |
|
if((PPM_in[EE_Parameter.Kanalbelegung[K_GAS]] > 80) && MotorenEin == 0) |
{ |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// auf Nullwerte kalibrieren |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(PPM_in[EE_Parameter.Kanalbelegung[K_GIER]] > 75) // Neutralwerte |
{ |
if(++delay_neutral > 200) // nicht sofort |
{ |
GRN_OFF; |
MotorenEin = 0; |
delay_neutral = 0; |
modell_fliegt = 0; |
if(PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] > 70 || abs(PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]]) > 70) |
{ |
unsigned char setting=1; |
if(PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] > 70 && PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] < 70) setting = 1; |
if(PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] > 70 && PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] > 70) setting = 2; |
if(PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] < 70 && PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] > 70) setting = 3; |
if(PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] <-70 && PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] > 70) setting = 4; |
if(PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] <-70 && PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] < 70) setting = 5; |
SetActiveParamSet(setting); // aktiven Datensatz merken |
} |
if(abs(PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]]) < 30 && PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] < -70) |
{ |
WinkelOut.CalcState = 1; |
beeptime = 1000; |
} |
else |
{ |
ParamSet_ReadFromEEProm(GetActiveParamSet()); |
LipoDetection(0); |
LIBFC_ReceiverInit(EE_Parameter.Receiver); |
if((EE_Parameter.GlobalConfig & CFG_HOEHENREGELUNG)) // Höhenregelung aktiviert? |
{ |
if((MessLuftdruck > 950) || (MessLuftdruck < 750)) SucheLuftruckOffset(); |
} |
ServoActive = 0; |
SetNeutral(0); |
calibration_done = 1; |
ServoActive = 1; |
DDRD |=0x80; // enable J7 -> Servo signal |
Piep(GetActiveParamSet(),120); |
#ifdef WITH_JETI_BEEP /// MartinW main.h |
#warning : "### with JetiBeep Delay ###" |
JetiBeep = 101;/// |
delayjetibeepset = (GetActiveParamSet()*10); |
#else |
#warning : "### without JetiBeep Delay ###" |
#endif |
} |
} |
} |
else |
if(PPM_in[EE_Parameter.Kanalbelegung[K_GIER]] < -75) // ACC Neutralwerte speichern |
{ |
if(++delay_neutral > 200) // nicht sofort |
{ |
GRN_OFF; |
MotorenEin = 0; |
delay_neutral = 0; |
modell_fliegt = 0; |
SetNeutral(1); |
calibration_done = 1; |
Piep(GetActiveParamSet(),120); |
} |
} |
else delay_neutral = 0; |
} |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Gas ist unten |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
|
if(PPM_in[EE_Parameter.Kanalbelegung[K_GAS]] < 35-120) |
{ |
// Motoren Starten |
if(!MotorenEin) |
{ |
if((PPM_in[EE_Parameter.Kanalbelegung[K_GIER]] < -75) && (PPM_in[EE_Parameter.MotorSafetySwitch] < -75 || EE_Parameter.MotorSafetySwitch == 0)) |
{ |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Einschalten |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(++delay_einschalten > 200) |
{ |
delay_einschalten = 0; |
if(!VersionInfo.HardwareError[0] && calibration_done && !NC_ErrorCode) |
{ |
modell_fliegt = 1; |
MotorenEin = 1; |
sollGier = 0; |
Mess_Integral_Gier = 0; |
//Mess_Integral_Gier2 = 0; //MartinR: Mess_Integral_Gier2 unbenutzt |
Mess_IntegralNick = EE_Parameter.GyroAccFaktor * (long)Mittelwert_AccNick; |
Mess_IntegralRoll = EE_Parameter.GyroAccFaktor * (long)Mittelwert_AccRoll; |
Mess_IntegralNick2 = IntegralNick; |
Mess_IntegralRoll2 = IntegralRoll; |
SummeNick = 0; |
SummeRoll = 0; |
FC_StatusFlags |= FC_STATUS_START; |
ControlHeading = (((int) EE_Parameter.OrientationAngle * 15 + KompassValue) % 360) / 2; |
NeueKompassRichtungMerken = 100; // 2 sekunden |
} |
else |
{ |
beeptime = 1500; // indicate missing calibration |
} |
} |
} |
else delay_einschalten = 0; |
} |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Auschalten |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
else // only if motors are running |
{ |
if((PPM_in[EE_Parameter.Kanalbelegung[K_GIER]] > 75) && (PPM_in[EE_Parameter.MotorSafetySwitch] < -75 || EE_Parameter.MotorSafetySwitch == 0)) |
{ |
if(++delay_ausschalten > 200) // nicht sofort |
{ |
MotorenEin = 0; |
delay_ausschalten = 0; |
modell_fliegt = 0; |
} |
} |
else delay_ausschalten = 0; |
} |
} |
} |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// neue Werte von der Funke |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
|
if(!NewPpmData-- || (FC_StatusFlags & FC_STATUS_EMERGENCY_LANDING)) |
{ |
static int stick_nick,stick_roll; |
ParameterZuordnung(); |
stick_nick = (stick_nick * 3 + PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] * EE_Parameter.Stick_P) / 4; |
stick_nick += PPM_diff[EE_Parameter.Kanalbelegung[K_NICK]] * EE_Parameter.Stick_D; |
stick_roll = (stick_roll * 3 + PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] * EE_Parameter.Stick_P) / 4; |
stick_roll += PPM_diff[EE_Parameter.Kanalbelegung[K_ROLL]] * EE_Parameter.Stick_D; |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// CareFree und freie Wahl der vorderen Richtung |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(CareFree) |
{ |
signed int nick, roll; |
nick = stick_nick / 4; |
roll = stick_roll / 4; |
StickNick = ((FromNC_Rotate_C * nick) + (FromNC_Rotate_S * roll)) / (32 / 4); |
StickRoll = ((FromNC_Rotate_C * roll) - (FromNC_Rotate_S * nick)) / (32 / 4); |
} |
else |
{ |
FromNC_Rotate_C = sintab[EE_Parameter.OrientationAngle + 6]; |
FromNC_Rotate_S = sintab[EE_Parameter.OrientationAngle]; |
StickNick = ((FromNC_Rotate_C * stick_nick) + (FromNC_Rotate_S * stick_roll)) / 8; |
StickRoll = ((FromNC_Rotate_C * stick_roll) - (FromNC_Rotate_S * stick_nick)) / 8; |
} |
|
StickGier = -PPM_in[EE_Parameter.Kanalbelegung[K_GIER]]; |
if(StickGier > 4) StickGier -= 4; else |
if(StickGier < -4) StickGier += 4; else StickGier = 0; |
|
StickNick -= (GPS_Nick + GPS_Nick2); |
StickRoll -= (GPS_Roll + GPS_Roll2); |
StickGas = PPM_in[EE_Parameter.Kanalbelegung[K_GAS]] + 120; |
|
GyroFaktor = (Parameter_Gyro_P + 10.0); |
IntegralFaktor = Parameter_Gyro_I; |
GyroFaktorGier = (Parameter_Gyro_Gier_P + 10.0); |
IntegralFaktorGier = Parameter_Gyro_Gier_I; |
|
//+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
//+ Analoge Steuerung per Seriell |
//+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
#ifdef WITH_ExternControl /// MartinW memorysaving |
#warning : "### with ExternControl ###" |
|
if(ExternControl.Config & 0x01 && Parameter_ExternalControl > 128) |
{ |
StickNick += (int) ExternControl.Nick * (int) EE_Parameter.Stick_P; |
StickRoll += (int) ExternControl.Roll * (int) EE_Parameter.Stick_P; |
StickGier += ExternControl.Gier; |
ExternHoehenValue = (int) ExternControl.Hight * (int)EE_Parameter.Hoehe_Verstaerkung; |
if(ExternControl.Gas < StickGas) StickGas = ExternControl.Gas; |
} |
if(StickGas < 0) StickGas = 0; |
|
if(EE_Parameter.GlobalConfig & CFG_HEADING_HOLD) IntegralFaktor = 0; |
|
if(abs(StickNick/STICK_GAIN) > MaxStickNick) |
{ |
MaxStickNick = abs(StickNick)/STICK_GAIN; |
if(MaxStickNick > 100) MaxStickNick = 100; |
} |
else MaxStickNick--; |
if(abs(StickRoll/STICK_GAIN) > MaxStickRoll) |
{ |
MaxStickRoll = abs(StickRoll)/STICK_GAIN; |
if(MaxStickRoll > 100) MaxStickRoll = 100; |
} |
else MaxStickRoll--; |
if(FC_StatusFlags & FC_STATUS_EMERGENCY_LANDING) {MaxStickNick = 0; MaxStickRoll = 0;} |
|
#else |
#warning : "### without ExternControl ###" |
#endif |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Looping? |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if((PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] > EE_Parameter.LoopThreshold) && EE_Parameter.BitConfig & CFG_LOOP_LINKS) Looping_Links = 1; |
else |
{ |
{ |
if((PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] < (EE_Parameter.LoopThreshold - EE_Parameter.LoopHysterese))) Looping_Links = 0; |
} |
} |
if((PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] < -EE_Parameter.LoopThreshold) && EE_Parameter.BitConfig & CFG_LOOP_RECHTS) Looping_Rechts = 1; |
else |
{ |
if(Looping_Rechts) // Hysterese |
{ |
if(PPM_in[EE_Parameter.Kanalbelegung[K_ROLL]] > -(EE_Parameter.LoopThreshold - EE_Parameter.LoopHysterese)) Looping_Rechts = 0; |
} |
} |
|
if((PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] > EE_Parameter.LoopThreshold) && EE_Parameter.BitConfig & CFG_LOOP_OBEN) Looping_Oben = 1; |
else |
{ |
if(Looping_Oben) // Hysterese |
{ |
if((PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] < (EE_Parameter.LoopThreshold - EE_Parameter.LoopHysterese))) Looping_Oben = 0; |
} |
} |
if((PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] < -EE_Parameter.LoopThreshold) && EE_Parameter.BitConfig & CFG_LOOP_UNTEN) Looping_Unten = 1; |
else |
{ |
if(Looping_Unten) // Hysterese |
{ |
if(PPM_in[EE_Parameter.Kanalbelegung[K_NICK]] > -(EE_Parameter.LoopThreshold - EE_Parameter.LoopHysterese)) Looping_Unten = 0; |
} |
} |
|
if(Looping_Links || Looping_Rechts) Looping_Roll = 1; else Looping_Roll = 0; |
if(Looping_Oben || Looping_Unten) { Looping_Nick = 1; Looping_Roll = 0; Looping_Links = 0; Looping_Rechts = 0;} else Looping_Nick = 0; |
} // Ende neue Funken-Werte |
|
if(Looping_Roll || Looping_Nick) |
{ |
if(GasMischanteil > EE_Parameter.LoopGasLimit) GasMischanteil = EE_Parameter.LoopGasLimit; |
TrichterFlug = 1; |
} |
|
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Bei Empfangsausfall im Flug |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(FC_StatusFlags & FC_STATUS_EMERGENCY_LANDING) |
{ |
StickGier = 0; |
StickNick = 0; |
StickRoll = 0; |
GyroFaktor = 90; |
IntegralFaktor = 120; |
GyroFaktorGier = 90; |
IntegralFaktorGier = 120; |
Looping_Roll = 0; |
Looping_Nick = 0; |
} |
|
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Integrale auf ACC-Signal abgleichen |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
#define ABGLEICH_ANZAHL 256L |
|
MittelIntegralNick += IntegralNick; // Für die Mittelwertbildung aufsummieren |
MittelIntegralRoll += IntegralRoll; |
MittelIntegralNick2 += IntegralNick2; |
MittelIntegralRoll2 += IntegralRoll2; |
|
if(Looping_Nick || Looping_Roll) |
{ |
IntegralAccNick = 0; |
IntegralAccRoll = 0; |
MittelIntegralNick = 0; |
MittelIntegralRoll = 0; |
MittelIntegralNick2 = 0; |
MittelIntegralRoll2 = 0; |
Mess_IntegralNick2 = Mess_IntegralNick; |
Mess_IntegralRoll2 = Mess_IntegralRoll; |
ZaehlMessungen = 0; |
LageKorrekturNick = 0; |
LageKorrekturRoll = 0; |
} |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(!Looping_Nick && !Looping_Roll && (Aktuell_az > 512 || MotorenEin)) |
{ |
long tmp_long, tmp_long2; |
if(FromNaviCtrl_Value.Kalman_K > 0 /*&& !TrichterFlug*/) |
{ |
tmp_long = (long)(IntegralNick / EE_Parameter.GyroAccFaktor - (long)Mittelwert_AccNick); |
tmp_long2 = (long)(IntegralRoll / EE_Parameter.GyroAccFaktor - (long)Mittelwert_AccRoll); |
tmp_long = (tmp_long * FromNaviCtrl_Value.Kalman_K) / (32 * 16); |
tmp_long2 = (tmp_long2 * FromNaviCtrl_Value.Kalman_K) / (32 * 16); |
KompassFusion = FromNaviCtrl_Value.Kalman_K; |
if((MaxStickNick > 64) || (MaxStickRoll > 64)) |
{ |
tmp_long /= 2; |
tmp_long2 /= 2; |
} |
if(abs(PPM_in[EE_Parameter.Kanalbelegung[K_GIER]]) > 25) |
{ |
tmp_long /= 3; |
tmp_long2 /= 3; |
} |
if(tmp_long > (long) FromNaviCtrl_Value.Kalman_MaxFusion) tmp_long = (long) FromNaviCtrl_Value.Kalman_MaxFusion; |
if(tmp_long < (long)-FromNaviCtrl_Value.Kalman_MaxFusion) tmp_long = (long)-FromNaviCtrl_Value.Kalman_MaxFusion; |
if(tmp_long2 > (long) FromNaviCtrl_Value.Kalman_MaxFusion) tmp_long2 = (long) FromNaviCtrl_Value.Kalman_MaxFusion; |
if(tmp_long2 < (long)-FromNaviCtrl_Value.Kalman_MaxFusion) tmp_long2 = (long)-FromNaviCtrl_Value.Kalman_MaxFusion; |
} |
else |
{ |
tmp_long = (long)(IntegralNick / EE_Parameter.GyroAccFaktor - (long)Mittelwert_AccNick); |
tmp_long2 = (long)(IntegralRoll / EE_Parameter.GyroAccFaktor - (long)Mittelwert_AccRoll); |
tmp_long /= 16; |
tmp_long2 /= 16; |
if((MaxStickNick > 64) || (MaxStickRoll > 64)) |
{ |
tmp_long /= 3; |
tmp_long2 /= 3; |
} |
if(abs(PPM_in[EE_Parameter.Kanalbelegung[K_GIER]]) > 25) |
{ |
tmp_long /= 3; |
tmp_long2 /= 3; |
} |
KompassFusion = 25; |
#define AUSGLEICH 32 |
if(tmp_long > AUSGLEICH) tmp_long = AUSGLEICH; |
if(tmp_long < -AUSGLEICH) tmp_long =-AUSGLEICH; |
if(tmp_long2 > AUSGLEICH) tmp_long2 = AUSGLEICH; |
if(tmp_long2 <-AUSGLEICH) tmp_long2 =-AUSGLEICH; |
} |
|
Mess_IntegralNick -= tmp_long; |
Mess_IntegralRoll -= tmp_long2; |
} |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(ZaehlMessungen >= ABGLEICH_ANZAHL) |
{ |
static int cnt = 0; |
static char last_n_p,last_n_n,last_r_p,last_r_n; |
static long MittelIntegralNick_Alt,MittelIntegralRoll_Alt; |
if(!Looping_Nick && !Looping_Roll && !TrichterFlug && EE_Parameter.Driftkomp) |
{ |
MittelIntegralNick /= ABGLEICH_ANZAHL; |
MittelIntegralRoll /= ABGLEICH_ANZAHL; |
IntegralAccNick = (EE_Parameter.GyroAccFaktor * IntegralAccNick) / ABGLEICH_ANZAHL; |
IntegralAccRoll = (EE_Parameter.GyroAccFaktor * IntegralAccRoll) / ABGLEICH_ANZAHL; |
IntegralAccZ = IntegralAccZ / ABGLEICH_ANZAHL; |
#define MAX_I 0 |
// Nick ++++++++++++++++++++++++++++++++++++++++++++++++ |
IntegralFehlerNick = (long)(MittelIntegralNick - (long)IntegralAccNick); |
ausgleichNick = IntegralFehlerNick / EE_Parameter.GyroAccAbgleich; |
// Roll ++++++++++++++++++++++++++++++++++++++++++++++++ |
IntegralFehlerRoll = (long)(MittelIntegralRoll - (long)IntegralAccRoll); |
ausgleichRoll = IntegralFehlerRoll / EE_Parameter.GyroAccAbgleich; |
|
LageKorrekturNick = ausgleichNick / ABGLEICH_ANZAHL; |
LageKorrekturRoll = ausgleichRoll / ABGLEICH_ANZAHL; |
|
if(((MaxStickNick > 64) || (MaxStickRoll > 64) || (abs(PPM_in[EE_Parameter.Kanalbelegung[K_GIER]]) > 25)) && (FromNaviCtrl_Value.Kalman_K == -1)) |
{ |
LageKorrekturNick /= 2; |
LageKorrekturRoll /= 2; |
} |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Gyro-Drift ermitteln |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
MittelIntegralNick2 /= ABGLEICH_ANZAHL; |
MittelIntegralRoll2 /= ABGLEICH_ANZAHL; |
tmp_long = IntegralNick2 - IntegralNick; |
tmp_long2 = IntegralRoll2 - IntegralRoll; |
|
IntegralFehlerNick = tmp_long; |
IntegralFehlerRoll = tmp_long2; |
Mess_IntegralNick2 -= IntegralFehlerNick; |
Mess_IntegralRoll2 -= IntegralFehlerRoll; |
|
if(EE_Parameter.Driftkomp) |
{ |
if(GierGyroFehler > ABGLEICH_ANZAHL/2) { AdNeutralGier++; } |
if(GierGyroFehler <-ABGLEICH_ANZAHL/2) { AdNeutralGier--; } |
} |
GierGyroFehler = 0; |
|
#define FEHLER_LIMIT (ABGLEICH_ANZAHL / 2) |
#define FEHLER_LIMIT1 (ABGLEICH_ANZAHL * 2) //4 |
#define FEHLER_LIMIT2 (ABGLEICH_ANZAHL * 16) //16 |
#define BEWEGUNGS_LIMIT 20000 |
// Nick +++++++++++++++++++++++++++++++++++++++++++++++++ |
cnt = 1;// + labs(IntegralFehlerNick) / 4096; |
if(labs(IntegralFehlerNick) > FEHLER_LIMIT1) cnt = 4; |
if(labs(MittelIntegralNick_Alt - MittelIntegralNick) < BEWEGUNGS_LIMIT || (FromNaviCtrl_Value.Kalman_MaxDrift > 3*8)) |
{ |
if(IntegralFehlerNick > FEHLER_LIMIT2) |
{ |
if(last_n_p) |
{ |
cnt += labs(IntegralFehlerNick) / (FEHLER_LIMIT2 / 8); |
ausgleichNick = IntegralFehlerNick / 8; |
if(ausgleichNick > 5000) ausgleichNick = 5000; |
LageKorrekturNick += ausgleichNick / ABGLEICH_ANZAHL; |
} |
else last_n_p = 1; |
} else last_n_p = 0; |
if(IntegralFehlerNick < -FEHLER_LIMIT2) |
{ |
if(last_n_n) |
{ |
cnt += labs(IntegralFehlerNick) / (FEHLER_LIMIT2 / 8); |
ausgleichNick = IntegralFehlerNick / 8; |
if(ausgleichNick < -5000) ausgleichNick = -5000; |
LageKorrekturNick += ausgleichNick / ABGLEICH_ANZAHL; |
} |
else last_n_n = 1; |
} else last_n_n = 0; |
} |
else |
{ |
cnt = 0; |
KompassSignalSchlecht = 100; |
} |
if(cnt > EE_Parameter.Driftkomp) cnt = EE_Parameter.Driftkomp; |
if(FromNaviCtrl_Value.Kalman_MaxDrift) if(cnt > FromNaviCtrl_Value.Kalman_MaxDrift) cnt = FromNaviCtrl_Value.Kalman_MaxDrift; |
if(IntegralFehlerNick > FEHLER_LIMIT) AdNeutralNick += cnt; |
if(IntegralFehlerNick < -FEHLER_LIMIT) AdNeutralNick -= cnt; |
|
// Roll +++++++++++++++++++++++++++++++++++++++++++++++++ |
cnt = 1;// + labs(IntegralFehlerRoll) / 4096; |
if(labs(IntegralFehlerRoll) > FEHLER_LIMIT1) cnt = 4; |
if(labs(MittelIntegralRoll_Alt - MittelIntegralRoll) < BEWEGUNGS_LIMIT || (FromNaviCtrl_Value.Kalman_MaxDrift > 3*8)) |
{ |
if(IntegralFehlerRoll > FEHLER_LIMIT2) |
{ |
if(last_r_p) |
{ |
cnt += labs(IntegralFehlerRoll) / (FEHLER_LIMIT2 / 8); |
ausgleichRoll = IntegralFehlerRoll / 8; |
if(ausgleichRoll > 5000) ausgleichRoll = 5000; |
LageKorrekturRoll += ausgleichRoll / ABGLEICH_ANZAHL; |
} |
else last_r_p = 1; |
} else last_r_p = 0; |
if(IntegralFehlerRoll < -FEHLER_LIMIT2) |
{ |
if(last_r_n) |
{ |
cnt += labs(IntegralFehlerRoll) / (FEHLER_LIMIT2 / 8); |
ausgleichRoll = IntegralFehlerRoll / 8; |
if(ausgleichRoll < -5000) ausgleichRoll = -5000; |
LageKorrekturRoll += ausgleichRoll / ABGLEICH_ANZAHL; |
} |
else last_r_n = 1; |
} else last_r_n = 0; |
} else |
{ |
cnt = 0; |
KompassSignalSchlecht = 100; |
} |
if(cnt > EE_Parameter.Driftkomp) cnt = EE_Parameter.Driftkomp; |
if(FromNaviCtrl_Value.Kalman_MaxDrift) if(cnt > FromNaviCtrl_Value.Kalman_MaxDrift) cnt = FromNaviCtrl_Value.Kalman_MaxDrift; |
if(IntegralFehlerRoll > FEHLER_LIMIT) AdNeutralRoll += cnt; |
if(IntegralFehlerRoll < -FEHLER_LIMIT) AdNeutralRoll -= cnt; |
} |
else |
{ |
LageKorrekturRoll = 0; |
LageKorrekturNick = 0; |
TrichterFlug = 0; |
} |
|
if(!IntegralFaktor) { LageKorrekturRoll = 0; LageKorrekturNick = 0;} // z.B. bei HH |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++ |
MittelIntegralNick_Alt = MittelIntegralNick; |
MittelIntegralRoll_Alt = MittelIntegralRoll; |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++ |
IntegralAccNick = 0; |
IntegralAccRoll = 0; |
IntegralAccZ = 0; |
MittelIntegralNick = 0; |
MittelIntegralRoll = 0; |
MittelIntegralNick2 = 0; |
MittelIntegralRoll2 = 0; |
ZaehlMessungen = 0; |
} // ZaehlMessungen >= ABGLEICH_ANZAHL |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Gieren |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(abs(StickGier) > 3) // war 15 |
{ |
// KompassSignalSchlecht = 1000; |
if(!(EE_Parameter.GlobalConfig & CFG_KOMPASS_FIX)) |
{ |
NeueKompassRichtungMerken = 50; // eine Sekunde zum Einloggen |
}; |
} |
tmp_int = (long) EE_Parameter.Gier_P * ((long)StickGier * abs(StickGier)) / 512L; // expo y = ax + bx² |
tmp_int += (EE_Parameter.Gier_P * StickGier) / 4; |
tmp_int += CompassGierSetpoint; |
sollGier = tmp_int; |
Mess_Integral_Gier -= tmp_int; |
if(Mess_Integral_Gier > 50000) Mess_Integral_Gier = 50000; // begrenzen |
if(Mess_Integral_Gier <-50000) Mess_Integral_Gier =-50000; |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Kompass |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(KompassValue >= 0 && (EE_Parameter.GlobalConfig & CFG_KOMPASS_AKTIV)) |
{ |
if(CalculateCompassTimer-- == 1) |
{ |
int w,v,r,fehler,korrektur; // wird von der SPI-Routine auf 1 gesetzt |
CalculateCompassTimer = 13; // falls keine Navi-Daten |
// max. Korrekturwert schätzen |
w = abs(IntegralNick /512); // mit zunehmender Neigung den Einfluss drosseln |
v = abs(IntegralRoll /512); |
if(v > w) w = v; // grösste Neigung ermitteln |
korrektur = w / 4 + 1; |
// Kompassfehlerwert bestimmen |
fehler = ((540 + KompassValue - (ErsatzKompass/GIER_GRAD_FAKTOR)) % 360) - 180; |
// GIER_GRAD_FAKTOR ist ca. 1200 |
|
// Kompasswert einloggen |
if(KompassSignalSchlecht) KompassSignalSchlecht--; |
else |
if(w < 25) |
{ |
GierGyroFehler += fehler; |
if(NeueKompassRichtungMerken) |
{ |
if(--NeueKompassRichtungMerken == 0) |
{ |
ErsatzKompass = KompassValue * GIER_GRAD_FAKTOR; |
KompassSollWert = (ErsatzKompass/GIER_GRAD_FAKTOR); |
} |
} |
} |
// Kompass fusionieren |
if(!KompassSignalSchlecht) ErsatzKompass += (fehler * KompassFusion) / korrektur; |
|
// MK Gieren |
if(!NeueKompassRichtungMerken) |
{ |
r = ((540 + (KompassSollWert - ErsatzKompass/GIER_GRAD_FAKTOR)) % 360) - 180; |
v = r * (Parameter_KompassWirkung/2); // nach Kompass ausrichten |
CompassGierSetpoint = v / 16; |
} |
else CompassGierSetpoint = 0; |
} // CalculateCompassTimer |
} |
else CompassGierSetpoint = 0; |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Drehgeschwindigkeit und -winkel zu einem Istwert zusammenfassen |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(TrichterFlug) { SummeRoll = 0; SummeNick = 0;}; |
|
if(!Looping_Nick) IntegralNickMalFaktor = (IntegralNick * IntegralFaktor) / (44000 / STICK_GAIN); else IntegralNickMalFaktor = 0; |
if(!Looping_Roll) IntegralRollMalFaktor = (IntegralRoll * IntegralFaktor) / (44000 / STICK_GAIN); else IntegralRollMalFaktor = 0; |
|
#define TRIM_MAX 200 |
if(TrimNick > TRIM_MAX) TrimNick = TRIM_MAX; else if(TrimNick <-TRIM_MAX) TrimNick =-TRIM_MAX; |
if(TrimRoll > TRIM_MAX) TrimRoll = TRIM_MAX; else if(TrimRoll <-TRIM_MAX) TrimRoll =-TRIM_MAX; |
|
MesswertNick = IntegralNickMalFaktor + (long)((long)MesswertNick * GyroFaktor + (long)TrimNick * 128L) / (256L / STICK_GAIN); |
MesswertRoll = IntegralRollMalFaktor + (long)((long)MesswertRoll * GyroFaktor + (long)TrimRoll * 128L) / (256L / STICK_GAIN); |
MesswertGier = (long)(MesswertGier * 2 * (long)GyroFaktorGier) / (256L / STICK_GAIN) + (long)(Integral_Gier * IntegralFaktorGier) / (2 * (44000 / STICK_GAIN)); |
|
// Maximalwerte abfangen |
// #define MAX_SENSOR (4096*STICK_GAIN) |
#define MAX_SENSOR (4096) |
if(MesswertNick > MAX_SENSOR) MesswertNick = MAX_SENSOR; |
if(MesswertNick < -MAX_SENSOR) MesswertNick = -MAX_SENSOR; |
if(MesswertRoll > MAX_SENSOR) MesswertRoll = MAX_SENSOR; |
if(MesswertRoll < -MAX_SENSOR) MesswertRoll = -MAX_SENSOR; |
if(MesswertGier > MAX_SENSOR) MesswertGier = MAX_SENSOR; |
if(MesswertGier < -MAX_SENSOR) MesswertGier = -MAX_SENSOR; |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Höhenregelung |
// Die Höhenregelung schwächt lediglich das Gas ab, erhöht es allerdings nicht |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(UBat > BattLowVoltageWarning) GasMischanteil = ((unsigned int)GasMischanteil * BattLowVoltageWarning) / UBat; // Gas auf das aktuelle Spannungvieveau beziehen |
GasMischanteil *= STICK_GAIN; |
// if height control is activated |
if((EE_Parameter.GlobalConfig & CFG_HOEHENREGELUNG) && !(Looping_Roll || Looping_Nick)) // Höhenregelung |
{ |
#define HOVER_GAS_AVERAGE 16384L // 16384 * 2ms = 32s averaging |
#define HC_GAS_AVERAGE 4 // 4 * 2ms= 8ms averaging |
|
#if (defined(__AVR_ATmega1284__) || defined(__AVR_ATmega1284P__)) |
#define OPA_OFFSET_STEP 15 |
#else |
#define OPA_OFFSET_STEP 10 |
#endif |
int HCGas, HeightDeviation = 0,GasReduction = 0; |
static int HeightTrimming = 0; // rate for change of height setpoint |
static int FilterHCGas = 0; |
static int StickGasHover = 120, HoverGasMin = 0, HoverGasMax = 1023; |
static unsigned long HoverGasFilter = 0; |
static unsigned char delay = 100, BaroAtUpperLimit = 0, BaroAtLowerLimit = 0; |
static signed char WaypointTrimming = 0; |
int CosAttitude; // for projection of hoover gas |
|
// get the current hooverpoint |
DebugOut.Analog[21] = HoverGas; |
|
// Expand the measurement |
// measurement of air pressure close to upper limit and no overflow in correction of the new OCR0A value occurs |
if(!BaroExpandActive) |
{ |
if(MessLuftdruck > 920) |
{ // increase offset |
if(OCR0A < (255 - OPA_OFFSET_STEP)) |
{ |
ExpandBaro -= 1; |
OCR0A = DruckOffsetSetting - OPA_OFFSET_STEP * ExpandBaro; // increase offset to shift ADC down |
beeptime = 300; |
BaroExpandActive = 350; |
} |
else |
{ |
BaroAtLowerLimit = 1; |
} |
} |
// measurement of air pressure close to lower limit and |
else |
if(MessLuftdruck < 100) |
{ // decrease offset |
if(OCR0A > OPA_OFFSET_STEP) |
{ |
ExpandBaro += 1; |
OCR0A = DruckOffsetSetting - OPA_OFFSET_STEP * ExpandBaro; // decrease offset to shift ADC up |
beeptime = 300; |
BaroExpandActive = 350; |
} |
else |
{ |
BaroAtUpperLimit = 1; |
} |
} |
else |
{ |
BaroAtUpperLimit = 0; |
BaroAtLowerLimit = 0; |
} |
} |
else // delay, because of expanding the Baro-Range |
{ |
// now clear the D-values |
SummenHoehe = HoehenWert * SM_FILTER; |
VarioMeter = 0; |
BaroExpandActive--; |
} |
|
// if height control is activated by an rc channel |
if(EE_Parameter.GlobalConfig & CFG_HOEHEN_SCHALTER) // Regler wird über Schalter gesteuert |
{ // check if parameter is less than activation threshold |
if(Parameter_MaxHoehe < 50) // for 3 or 2-state switch height control is disabled in lowest position |
{ //height control not active |
if(!delay--) |
{ |
HoehenReglerAktiv = 0; // disable height control |
SollHoehe = HoehenWert; // update SetPoint with current reading |
delay = 1; |
} |
} |
else |
{ //height control is activated |
HoehenReglerAktiv = 1; // enable height control |
delay = 200; |
} |
} |
else // no switchable height control |
{ |
SollHoehe = ((int16_t) ExternHoehenValue + (int16_t) Parameter_MaxHoehe) * (int)EE_Parameter.Hoehe_Verstaerkung; |
HoehenReglerAktiv = 1; |
} |
|
// calculate cos of nick and roll angle used for projection of the vertical hoover gas |
tmp_int = (int)(IntegralNick/GIER_GRAD_FAKTOR); // nick angle in deg |
tmp_int2 = (int)(IntegralRoll/GIER_GRAD_FAKTOR); // roll angle in deg |
CosAttitude = (int16_t)ihypot(tmp_int, tmp_int2); // phytagoras gives effective attitude angle in deg |
LIMIT_MAX(CosAttitude, 60); // limit effective attitude angle |
CosAttitude = c_cos_8192(CosAttitude); // cos of actual attitude |
VarioCharacter = ' '; |
if(HoehenReglerAktiv && !(FC_StatusFlags & FC_STATUS_EMERGENCY_LANDING)) |
{ |
#define HEIGHT_CONTROL_STICKTHRESHOLD 15 |
// Holger original version |
// start of height control algorithm |
// the height control is only an attenuation of the actual gas stick. |
// I.e. it will work only if the gas stick is higher than the hover gas |
// and the hover height will be allways larger than height setpoint. |
FC_StatusFlags2 |= FC_STATUS2_ALTITUDE_CONTROL; |
if((EE_Parameter.ExtraConfig & CFG2_HEIGHT_LIMIT) || !(EE_Parameter.GlobalConfig & CFG_HOEHEN_SCHALTER)) // Regler wird über Schalter gesteuert) |
{ // old version |
HCGas = GasMischanteil; // take current stick gas as neutral point for the height control |
HeightTrimming = 0; |
// set both flags to indicate no vario mode |
FC_StatusFlags |= (FC_STATUS_VARIO_TRIM_UP|FC_STATUS_VARIO_TRIM_DOWN); |
} |
else |
{ |
// alternative height control |
// PD-Control with respect to hoover point |
// the thrust loss out of horizontal attitude is compensated |
// the setpoint will be fine adjusted with the gas stick position |
if(FC_StatusFlags & FC_STATUS_FLY) // trim setpoint only when flying |
{ // gas stick is above hoover point |
if(StickGas > (StickGasHover + HEIGHT_CONTROL_STICKTHRESHOLD) && !BaroAtUpperLimit) |
{ |
if(FC_StatusFlags & FC_STATUS_VARIO_TRIM_DOWN) |
{ |
FC_StatusFlags &= ~FC_STATUS_VARIO_TRIM_DOWN; |
SollHoehe = HoehenWert; // update setpoint to current heigth |
} |
FC_StatusFlags |= FC_STATUS_VARIO_TRIM_UP; |
HeightTrimming += abs(StickGas - (StickGasHover + HEIGHT_CONTROL_STICKTHRESHOLD)); |
VarioCharacter = '+'; |
WaypointTrimming = 0; |
} // gas stick is below hoover point |
else if(StickGas < (StickGasHover - HEIGHT_CONTROL_STICKTHRESHOLD) && !BaroAtLowerLimit ) |
{ |
if(FC_StatusFlags & FC_STATUS_VARIO_TRIM_UP) |
{ |
FC_StatusFlags &= ~FC_STATUS_VARIO_TRIM_UP; |
SollHoehe = HoehenWert; // update setpoint to current heigth |
} |
FC_StatusFlags |= FC_STATUS_VARIO_TRIM_DOWN; |
HeightTrimming -= abs(StickGas - (StickGasHover - HEIGHT_CONTROL_STICKTHRESHOLD)); |
VarioCharacter = '-'; |
WaypointTrimming = 0; |
} |
else // Gas Stick in Hover Range |
{ |
VarioCharacter = '='; |
if(FromNC_AltitudeSpeed && FromNC_AltitudeSetpoint > SollHoehe) // von NC gesteuert -> Steigen |
{ |
FC_StatusFlags |= FC_STATUS_VARIO_TRIM_UP; |
HeightTrimming += FromNC_AltitudeSpeed; |
WaypointTrimming = 10; |
VarioCharacter = '^'; |
if(FC_StatusFlags & FC_STATUS_VARIO_TRIM_DOWN) // changed from sinking to rising |
{ |
FC_StatusFlags &= ~FC_STATUS_VARIO_TRIM_DOWN; |
SollHoehe = HoehenWert; // update setpoint to current heigth |
} |
} |
else |
if(FromNC_AltitudeSpeed && FromNC_AltitudeSetpoint < SollHoehe) // von NC gesteuert -> sinken |
{ |
FC_StatusFlags |= FC_STATUS_VARIO_TRIM_DOWN; |
HeightTrimming -= FromNC_AltitudeSpeed; |
WaypointTrimming = -10; |
VarioCharacter = 'v'; |
if(FC_StatusFlags & FC_STATUS_VARIO_TRIM_UP) // changed from rising to sinking |
{ |
FC_StatusFlags &= ~FC_STATUS_VARIO_TRIM_UP; |
SollHoehe = HoehenWert; // update setpoint to current heigth |
} |
} |
else |
if(FC_StatusFlags & (FC_STATUS_VARIO_TRIM_UP|FC_STATUS_VARIO_TRIM_DOWN)) |
{ |
if(!WaypointTrimming) SollHoehe = HoehenWert; // update setpoint to current height |
else WaypointTrimming = 0; |
FC_StatusFlags &= ~(FC_STATUS_VARIO_TRIM_UP|FC_STATUS_VARIO_TRIM_DOWN); |
HeightTrimming = 0; |
if(EE_Parameter.ExtraConfig & CFG2_VARIO_BEEP) beeptime = 500; |
if(!StartTrigger && HoehenWert > 50) |
{ |
StartTrigger = 1; |
} |
} |
} |
// Trim height set point |
if(abs(HeightTrimming) > 512) |
{ |
if(WaypointTrimming) |
{ |
if(abs(FromNC_AltitudeSetpoint - SollHoehe) < 10) SollHoehe = FromNC_AltitudeSetpoint; |
else SollHoehe += WaypointTrimming; |
} |
else |
SollHoehe += (HeightTrimming * EE_Parameter.Hoehe_Verstaerkung)/(5 * 512 / 2); // move setpoint |
HeightTrimming = 0; |
LIMIT_MIN_MAX(SollHoehe, (HoehenWert-1024), (HoehenWert+1024)); // max. 10m Unterschied |
if(EE_Parameter.ExtraConfig & CFG2_VARIO_BEEP) beeptime = 100; |
//update hoover gas stick value when setpoint is shifted |
if(!EE_Parameter.Hoehe_StickNeutralPoint && FromNC_AltitudeSpeed == 0) |
{ |
StickGasHover = HoverGas/STICK_GAIN; //rescale back to stick value |
StickGasHover = (StickGasHover * UBat) / BattLowVoltageWarning; |
if(StickGasHover < 70) StickGasHover = 70; |
else if(StickGasHover > 150) StickGasHover = 150; |
} |
} |
if(BaroExpandActive) SollHoehe = HoehenWert; // update setpoint to current altitude if Expanding is active |
} //if FCFlags & MKFCFLAG_FLY |
else |
{ |
SollHoehe = HoehenWert - 400; |
if(EE_Parameter.Hoehe_StickNeutralPoint) StickGasHover = EE_Parameter.Hoehe_StickNeutralPoint; |
else StickGasHover = 120; |
HoverGas = GasMischanteil; |
} |
HCGas = HoverGas; // take hover gas (neutral point) |
} |
if(HoehenWert > SollHoehe || !(EE_Parameter.ExtraConfig & CFG2_HEIGHT_LIMIT)) |
{ |
// from this point the Heigth Control Algorithm is identical for both versions |
if(BaroExpandActive) // baro range expanding active |
{ |
HCGas = HoverGas; // hover while expanding baro adc range |
HeightDeviation = 0; |
} // EOF // baro range expanding active |
else // valid data from air pressure sensor |
{ |
// ------------------------- P-Part ---------------------------- |
tmp_long = (HoehenWert - SollHoehe); // positive when too high |
LIMIT_MIN_MAX(tmp_long, -32767L, 32767L); // avoid overflov when casting to int16_t |
HeightDeviation = (int)(tmp_long); // positive when too high |
tmp_long = (tmp_long * (long)Parameter_Hoehe_P) / 32L; // p-part |
LIMIT_MIN_MAX(tmp_long, -127 * STICK_GAIN, 256 * STICK_GAIN); // more than the full range makes no sense |
GasReduction = tmp_long; |
// ------------------------- D-Part 1: Vario Meter ---------------------------- |
tmp_int = VarioMeter / 8; |
LIMIT_MIN_MAX(tmp_int, -127, 128); |
tmp_int = (tmp_int * (long)Parameter_Luftdruck_D) / 4L; // scale to d-gain parameter |
LIMIT_MIN_MAX(tmp_int,-64 * STICK_GAIN, 64 * STICK_GAIN); |
if(FC_StatusFlags & (FC_STATUS_VARIO_TRIM_UP|FC_STATUS_VARIO_TRIM_DOWN)) tmp_int /= 4; // reduce d-part while trimming setpoint |
else |
if(EE_Parameter.ExtraConfig & CFG2_HEIGHT_LIMIT) tmp_int /= 8; // reduce d-part in "Deckel" mode |
GasReduction += tmp_int; |
} // EOF no baro range expanding |
// ------------------------ D-Part 2: ACC-Z Integral ------------------------ |
if(Parameter_Hoehe_ACC_Wirkung) |
{ |
tmp_long = ((Mess_Integral_Hoch / 128L) * (int32_t) Parameter_Hoehe_ACC_Wirkung) / (128L / STICK_GAIN); |
LIMIT_MIN_MAX(tmp_long, -32 * STICK_GAIN, 64 * STICK_GAIN); |
GasReduction += tmp_long; |
} |
// ------------------------ D-Part 3: GpsZ ---------------------------------- |
tmp_int = (Parameter_Hoehe_GPS_Z * (int)FromNaviCtrl_Value.GpsZ)/128L; |
LIMIT_MIN_MAX(tmp_int, -32 * STICK_GAIN, 64 * STICK_GAIN); |
GasReduction += tmp_int; |
GasReduction = (long)((long)GasReduction * HoverGas) / 512; // scale to the gas value |
// ------------------------ ---------------------------------- |
HCGas -= GasReduction; |
// limit deviation from hoover point within the target region |
if(!HeightTrimming && HoverGas > 0) // height setpoint is not changed and hoover gas not zero |
{ |
unsigned int tmp; |
tmp = abs(HeightDeviation); |
if(tmp <= 60) |
{ |
LIMIT_MIN_MAX(HCGas, HoverGasMin, HoverGasMax); // limit gas around the hoover point |
} |
else |
{ |
tmp = (tmp - 60) / 32; |
if(tmp > 15) tmp = 15; |
if(HeightDeviation > 0) |
{ |
tmp = (HoverGasMin * (16 - tmp)) / 16; |
LIMIT_MIN_MAX(HCGas, tmp, HoverGasMax); // limit gas around the hoover point |
} |
else |
{ |
tmp = (HoverGasMax * (tmp + 16)) / 16; |
LIMIT_MIN_MAX(HCGas, HoverGasMin, tmp); // limit gas around the hoover point |
} |
} |
} |
// strech control output by inverse attitude projection 1/cos |
// + 1/cos(angle) ++++++++++++++++++++++++++ |
tmp_long2 = (int32_t)HCGas; |
tmp_long2 *= 8192L; |
tmp_long2 /= CosAttitude; |
HCGas = (int16_t)tmp_long2; |
// update height control gas averaging |
FilterHCGas = (FilterHCGas * (HC_GAS_AVERAGE - 1) + HCGas) / HC_GAS_AVERAGE; |
// limit height control gas pd-control output |
LIMIT_MIN_MAX(FilterHCGas, EE_Parameter.Hoehe_MinGas * STICK_GAIN, (MAX_GAS - 20) * STICK_GAIN); |
// set GasMischanteil to HeightControlGasFilter |
if(EE_Parameter.ExtraConfig & CFG2_HEIGHT_LIMIT) |
{ // old version |
LIMIT_MAX(FilterHCGas, GasMischanteil); // nicht mehr als Gas |
GasMischanteil = FilterHCGas; |
} |
else GasMischanteil = FilterHCGas + (GasMischanteil - HoverGas) / 4; // only in Vario-Mode |
} |
}// EOF height control active |
else // HC not active |
{ |
//update hoover gas stick value when HC is not active |
if(!EE_Parameter.Hoehe_StickNeutralPoint) |
{ |
StickGasHover = HoverGas/STICK_GAIN; // rescale back to stick value |
StickGasHover = (StickGasHover * UBat) / BattLowVoltageWarning; |
} |
else StickGasHover = EE_Parameter.Hoehe_StickNeutralPoint; |
LIMIT_MIN_MAX(StickGasHover, 70, 150); // reserve some range for trim up and down |
FilterHCGas = GasMischanteil; |
// set both flags to indicate no vario mode |
FC_StatusFlags |= (FC_STATUS_VARIO_TRIM_UP|FC_STATUS_VARIO_TRIM_DOWN); |
FC_StatusFlags2 &= ~FC_STATUS2_ALTITUDE_CONTROL; |
} |
// Hover gas estimation by averaging gas control output on small z-velocities |
// this is done only if height contol option is selected in global config and aircraft is flying |
if((FC_StatusFlags & FC_STATUS_FLY))// && !(FC_SatusFlags & FC_STATUS_EMERGENCY_LANDING)) |
{ |
if(HoverGasFilter == 0 || StartTrigger == 1) HoverGasFilter = HOVER_GAS_AVERAGE * (unsigned long)(GasMischanteil); // init estimation |
if(StartTrigger == 1) StartTrigger = 2; |
tmp_long2 = (int32_t)GasMischanteil; // take current thrust |
tmp_long2 *= CosAttitude; // apply attitude projection |
tmp_long2 /= 8192; |
// average vertical projected thrust |
if(modell_fliegt < 4000) // the first 8 seconds |
{ // reduce the time constant of averaging by factor of 4 to get much faster a stable value |
HoverGasFilter -= HoverGasFilter/(HOVER_GAS_AVERAGE/16L); |
HoverGasFilter += 16L * tmp_long2; |
} |
if(modell_fliegt < 8000) // the first 16 seconds |
{ // reduce the time constant of averaging by factor of 2 to get much faster a stable value |
HoverGasFilter -= HoverGasFilter/(HOVER_GAS_AVERAGE/4L); |
HoverGasFilter += 4L * tmp_long2; |
} |
else //later |
if(abs(VarioMeter) < 100 && abs(HoehenWert - SollHoehe) < 256) // only on small vertical speed & difference is small (only descending) |
{ |
HoverGasFilter -= HoverGasFilter/HOVER_GAS_AVERAGE; |
HoverGasFilter += tmp_long2; |
} |
HoverGas = (int16_t)(HoverGasFilter/HOVER_GAS_AVERAGE); |
if(EE_Parameter.Hoehe_HoverBand) |
{ |
int16_t band; |
band = HoverGas / EE_Parameter.Hoehe_HoverBand; // the higher the parameter the smaller the range |
HoverGasMin = HoverGas - band; |
HoverGasMax = HoverGas + band; |
} |
else |
{ // no limit |
HoverGasMin = 0; |
HoverGasMax = 1023; |
} |
} |
else |
{ |
StartTrigger = 0; |
HoverGasFilter = 0; |
HoverGas = 0; |
} |
}// EOF ParamSet.GlobalConfig & CFG_HEIGHT_CONTROL |
else |
{ |
// set undefined state to indicate vario off |
FC_StatusFlags |= (FC_STATUS_VARIO_TRIM_UP|FC_STATUS_VARIO_TRIM_DOWN); |
} // EOF no height control |
|
// limit gas to parameter setting |
LIMIT_MIN(GasMischanteil, (MIN_GAS + 10) * STICK_GAIN); |
if(GasMischanteil > (MAX_GAS - 20) * STICK_GAIN) GasMischanteil = (MAX_GAS - 20) * STICK_GAIN; |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// all BL-Ctrl connected? |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
if(MissingMotor || Capacity.MinOfMaxPWM != 255) |
if(modell_fliegt > 1 && modell_fliegt < 50 && GasMischanteil > 0) |
{ |
modell_fliegt = 1; |
GasMischanteil = (MIN_GAS + 10) * STICK_GAIN; |
} |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// + Mischer und PI-Regler |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
DebugOut.Analog[7] = GasMischanteil; |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Gier-Anteil |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
GierMischanteil = MesswertGier - sollGier * STICK_GAIN; // Regler für Gier |
#define MIN_GIERGAS (40*STICK_GAIN) // unter diesem Gaswert trotzdem Gieren |
if(GasMischanteil > MIN_GIERGAS) |
{ |
if(GierMischanteil > (GasMischanteil / 2)) GierMischanteil = GasMischanteil / 2; |
if(GierMischanteil < -(GasMischanteil / 2)) GierMischanteil = -(GasMischanteil / 2); |
} |
else |
{ |
if(GierMischanteil > (MIN_GIERGAS / 2)) GierMischanteil = MIN_GIERGAS / 2; |
if(GierMischanteil < -(MIN_GIERGAS / 2)) GierMischanteil = -(MIN_GIERGAS / 2); |
} |
tmp_int = MAX_GAS*STICK_GAIN; |
if(GierMischanteil > ((tmp_int - GasMischanteil))) GierMischanteil = ((tmp_int - GasMischanteil)); |
if(GierMischanteil < -((tmp_int - GasMischanteil))) GierMischanteil = -((tmp_int - GasMischanteil)); |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Nick-Achse |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
DiffNick = MesswertNick - StickNick; // Differenz bestimmen |
if(IntegralFaktor) SummeNick += IntegralNickMalFaktor - StickNick; // I-Anteil bei Winkelregelung |
else SummeNick += DiffNick; // I-Anteil bei HH |
if(SummeNick > (STICK_GAIN * 16000L)) SummeNick = (STICK_GAIN * 16000L); |
if(SummeNick < -(16000L * STICK_GAIN)) SummeNick = -(16000L * STICK_GAIN); |
|
if(EE_Parameter.Gyro_Stability <= 8) pd_ergebnis_nick = (EE_Parameter.Gyro_Stability * DiffNick) / 8; // PI-Regler für Nick |
else pd_ergebnis_nick = ((EE_Parameter.Gyro_Stability / 2) * DiffNick) / 4; // Überlauf verhindern |
pd_ergebnis_nick += SummeNick / Ki; |
|
tmp_int = (long)((long)Parameter_DynamicStability * (long)(GasMischanteil + abs(GierMischanteil)/2)) / 64; |
if(pd_ergebnis_nick > tmp_int) pd_ergebnis_nick = tmp_int; |
if(pd_ergebnis_nick < -tmp_int) pd_ergebnis_nick = -tmp_int; |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Roll-Achse |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
DiffRoll = MesswertRoll - StickRoll; // Differenz bestimmen |
if(IntegralFaktor) SummeRoll += IntegralRollMalFaktor - StickRoll;// I-Anteil bei Winkelregelung |
else SummeRoll += DiffRoll; // I-Anteil bei HH |
if(SummeRoll > (STICK_GAIN * 16000L)) SummeRoll = (STICK_GAIN * 16000L); |
if(SummeRoll < -(16000L * STICK_GAIN)) SummeRoll = -(16000L * STICK_GAIN); |
|
if(EE_Parameter.Gyro_Stability <= 8) pd_ergebnis_roll = (EE_Parameter.Gyro_Stability * DiffRoll) / 8; // PI-Regler für Roll |
else pd_ergebnis_roll = ((EE_Parameter.Gyro_Stability / 2) * DiffRoll) / 4; // Überlauf verhindern |
pd_ergebnis_roll += SummeRoll / Ki; |
|
tmp_int = (long)((long)Parameter_DynamicStability * (long)(GasMischanteil + abs(GierMischanteil)/2)) / 64; |
if(pd_ergebnis_roll > tmp_int) pd_ergebnis_roll = tmp_int; |
if(pd_ergebnis_roll < -tmp_int) pd_ergebnis_roll = -tmp_int; |
|
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
// Universal Mixer |
// +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
for(i=0; i<MAX_MOTORS; i++) |
{ |
signed int tmp_int; |
if(Mixer.Motor[i][0] > 0) |
{ |
// Gas |
if(Mixer.Motor[i][0] == 64) tmp_int = GasMischanteil; else tmp_int = ((long)GasMischanteil * Mixer.Motor[i][0]) / 64L; |
// Nick |
if(Mixer.Motor[i][1] == 64) tmp_int += pd_ergebnis_nick; |
else if(Mixer.Motor[i][1] == -64) tmp_int -= pd_ergebnis_nick; |
else tmp_int += ((long)pd_ergebnis_nick * Mixer.Motor[i][1]) / 64L; |
// Roll |
if(Mixer.Motor[i][2] == 64) tmp_int += pd_ergebnis_roll; |
else if(Mixer.Motor[i][2] == -64) tmp_int -= pd_ergebnis_roll; |
else tmp_int += ((long)pd_ergebnis_roll * Mixer.Motor[i][2]) / 64L; |
// Gier |
if(Mixer.Motor[i][3] == 64) tmp_int += GierMischanteil; |
else if(Mixer.Motor[i][3] == -64) tmp_int -= GierMischanteil; |
else tmp_int += ((long)GierMischanteil * Mixer.Motor[i][3]) / 64L; |
|
|
#ifdef WITH_ORIGINAL_MOTORSMOOTHING /// MartinW main.h means no memsave |
#warning : "### with WITH_ORIGINAL_MOTORSMOOTHING ###" |
if(tmp_int > tmp_motorwert[i]) tmp_int = (tmp_motorwert[i] + tmp_int) / 2; // MotorSmoothing |
else tmp_int = 2 * tmp_int - tmp_motorwert[i]; // MotorSmoothing |
#else |
#warning : "### without WITH_ORIGINAL_MOTORSMOOTHING, ajustable ###" |
// MartinW; variable MS START |
if(tmp_int > tmp_motorwert[i]) tmp_int = (tmp_motorwert[i] + tmp_int) / 2; // MotorSmoothing |
// else tmp_int = 2 * tmp_int - tmp_motorwert[i]; // MotorSmoothing |
// Arthur P: the original code allowed the motor value to drop to 0 or negative values |
// straight off, i.e. could amplify an intended decrease excessively while upregulation |
// is dampened. The modification would still allow immediate drop below intended value |
// but would dampen this. This would still allow for airbraking of the prop to have effect |
// but it might lead to less sudden excessive drops in rpm with only gradual recovery. |
// 090807 Arthur P: Due to problems with uart.c which still refers to user parameter 1 and 2 and |
// possible timing issues with the shutter interval load, removed the shutter interval functions |
// and switched to use of userparam6 for the motor smoothing. |
// 091114 Inserted modification into 0.76g source code. |
// 20100804 Modified v.0.80d code where motorsmoothing is no longer a separate function. |
// Downsmoothing either uses default v.0.7x+ 150% downstep (user para 7 == 0), |
// 50% downstep (user para 7 == 1 or 2), or downsteps of x% (userpara7 ==): |
// 66.6% (3), 75% (4), 80% (5), 90% (10), 95% (20), 97.5% (40), 98% (50), 99% (100). |
else |
{ |
if(Parameter_UserParam7 < 2) |
{ // Original function |
tmp_int = 2 * tmp_int - tmp_motorwert[i]; |
} |
else |
{ |
// If userpara7 >= 2 then allow >= 50% of the intended step down to rapidly reach the intended value. |
tmp_int = tmp_int + ((tmp_motorwert[i] - tmp_int)/Parameter_UserParam7); |
} |
} |
|
// MartinW; variable MS END |
#endif |
|
|
LIMIT_MIN_MAX(tmp_int,(int) MIN_GAS * 4,(int) MAX_GAS * 4); |
Motor[i].SetPoint = tmp_int / 4; |
Motor[i].SetPointLowerBits = (tmp_int % 4)<<1; // (3 bits total) |
tmp_motorwert[i] = tmp_int; |
} |
else |
{ |
Motor[i].SetPoint = 0; |
Motor[i].SetPointLowerBits = 0; |
} |
} |
} |