0,0 → 1,176 |
#ifndef _EEPROM_H |
#define _EEPROM_H |
|
#include <inttypes.h> |
|
#define EEPROM_ADR_PARAM_BEGIN 0 |
#define PID_PARAM_REVISION 1 // byte |
#define PID_ACTIVE_SET 2 // byte |
#define PID_PRESSURE_OFFSET 3 // byte |
#define PID_ACC_NICK 4 // word |
#define PID_ACC_ROLL 6 // word |
#define PID_ACC_TOP 8 // word |
|
#ifdef USE_KILLAGREG |
#define PID_MM3_X_OFF 11 // byte |
#define PID_MM3_Y_OFF 12 // byte |
#define PID_MM3_Z_OFF 13 // byte |
#define PID_MM3_X_RANGE 14 // word |
#define PID_MM3_Y_RANGE 16 // word |
#define PID_MM3_Z_RANGE 18 // word |
#endif |
|
|
#define EEPROM_ADR_CHANNELS 80 // 8 bytes |
|
#define EEPROM_ADR_PARAMSET_LENGTH 98 // word |
#define EEPROM_ADR_PARAMSET_BEGIN 100 |
|
|
#define EEPROM_ADR_MIXER_TABLE 1000 // 1000 - 1076 |
|
|
|
#define MIX_GAS 0 |
#define MIX_NICK 1 |
#define MIX_ROLL 2 |
#define MIX_YAW 3 |
|
typedef struct |
{ |
uint8_t Revision; |
int8_t Name[12]; |
int8_t Motor[16][4]; |
} __attribute__((packed)) MixerTable_t; |
|
extern MixerTable_t Mixer; |
|
|
// bit mask for ParamSet.GlobalConfig |
#define CFG_HEIGHT_CONTROL 0x01 |
#define CFG_HEIGHT_SWITCH 0x02 |
#define CFG_HEADING_HOLD 0x04 |
#define CFG_COMPASS_ACTIVE 0x08 |
#define CFG_COMPASS_FIX 0x10 |
#define CFG_GPS_ACTIVE 0x20 |
#define CFG_AXIS_COUPLING_ACTIVE 0x40 |
#define CFG_ROTARY_RATE_LIMITER 0x80 |
|
// bit mask for ParamSet.BitConfig |
#define CFG_LOOP_UP 0x01 |
#define CFG_LOOP_DOWN 0x02 |
#define CFG_LOOP_LEFT 0x04 |
#define CFG_LOOP_RIGHT 0x08 |
#define CFG_HEIGHT_3SWITCH 0x10 |
|
// defines for lookup ParamSet.ChannelAssignment |
#define CH_NICK 0 |
#define CH_ROLL 1 |
#define CH_GAS 2 |
#define CH_YAW 3 |
#define CH_POTI1 4 |
#define CH_POTI2 5 |
#define CH_POTI3 6 |
#define CH_POTI4 7 |
|
#define EEPARAM_REVISION 75 // is count up, if paramater stucture has changed (compatibility) |
#define EEMIXER_REVISION 1 // is count up, if Mixer stucture has changed (compatibility) |
|
// values above 250 representing poti1 to poti4 |
typedef struct |
{ |
uint8_t ChannelAssignment[8]; // see upper defines for details |
uint8_t GlobalConfig; // see upper defines for bitcoding |
uint8_t HeightMinGas; // Wert : 0-100 |
uint8_t HeightD; // Wert : 0-250 |
uint8_t MaxHeight; // Wert : 0-32 |
uint8_t HeightP; // Wert : 0-32 |
uint8_t Height_Gain; // Wert : 0-50 |
uint8_t Height_ACC_Effect; // Wert : 0-250 |
uint8_t StickP; // Wert : 1-6 |
uint8_t StickD; // Wert : 0-64 |
uint8_t StickYawP; // Wert : 1-20 |
uint8_t GasMin; // Wert : 0-32 |
uint8_t GasMax; // Wert : 33-250 |
uint8_t GyroAccFactor; // Wert : 1-64 |
uint8_t CompassYawEffect; // Wert : 0-32 |
uint8_t GyroP; // Wert : 10-250 |
uint8_t GyroI; // Wert : 0-250 |
uint8_t GyroD; // Wert : 0-250 |
uint8_t LowVoltageWarning; // Wert : 0-250 |
uint8_t EmergencyGas; // Wert : 0-250 //Gaswert bei Empängsverlust |
uint8_t EmergencyGasDuration; // Wert : 0-250 // Zeitbis auf EmergencyGas geschaltet wird, wg. Rx-Problemen |
uint8_t UfoArrangement; // x oder + Formation |
uint8_t IFactor; // Wert : 0-250 |
uint8_t UserParam1; // Wert : 0-250 |
uint8_t UserParam2; // Wert : 0-250 |
uint8_t UserParam3; // Wert : 0-250 |
uint8_t UserParam4; // Wert : 0-250 |
uint8_t ServoNickControl; // Wert : 0-250 // Stellung des Servos |
uint8_t ServoNickComp; // Wert : 0-250 // Einfluss Gyro/Servo |
uint8_t ServoNickMin; // Wert : 0-250 // Anschlag |
uint8_t ServoNickMax; // Wert : 0-250 // Anschlag |
uint8_t ServoRefresh; // Wert: 0-250 // Refreshrate of servo pwm output |
uint8_t LoopGasLimit; // Wert: 0-250 max. Gas während Looping |
uint8_t LoopThreshold; // Wert: 0-250 Schwelle für Stickausschlag |
uint8_t LoopHysteresis; // Wert: 0-250 Hysterese für Stickausschlag |
uint8_t AxisCoupling1; // Wert: 0-250 Faktor, mit dem Yaw die Achsen Roll und Nick koppelt (NickRollMitkopplung) |
uint8_t AxisCoupling2; // Wert: 0-250 Faktor, mit dem Nick und Roll verkoppelt werden |
uint8_t AxisCouplingYawCorrection;// Wert: 0-250 Faktor, mit dem Nick und Roll verkoppelt werden |
uint8_t AngleTurnOverNick; // Wert: 0-250 180°-Punkt |
uint8_t AngleTurnOverRoll; // Wert: 0-250 180°-Punkt |
uint8_t GyroAccTrim; // 1/k (Koppel_ACC_Wirkung) |
uint8_t DriftComp; // limit for gyrodrift compensation |
uint8_t DynamicStability; // PID limit for Attitude controller |
uint8_t UserParam5; // Wert : 0-250 |
uint8_t UserParam6; // Wert : 0-250 |
uint8_t UserParam7; // Wert : 0-250 |
uint8_t UserParam8; // Wert : 0-250 |
uint8_t J16Bitmask; // for the J16 Output |
uint8_t J16Timing; // for the J16 Output |
uint8_t J17Bitmask; // for the J17 Output |
uint8_t J17Timing; // for the J17 Output |
uint8_t NaviGpsModeControl; // Parameters for the Naviboard |
uint8_t NaviGpsGain; // overall gain for GPS-PID controller |
uint8_t NaviGpsP; // P gain for GPS-PID controller |
uint8_t NaviGpsI; // I gain for GPS-PID controller |
uint8_t NaviGpsD; // D gain for GPS-PID controller |
uint8_t NaviGpsPLimit; // P limit for GPS-PID controller |
uint8_t NaviGpsILimit; // I limit for GPS-PID controller |
uint8_t NaviGpsDLimit; // D limit for GPS-PID controller |
uint8_t NaviGpsACC; // ACC gain for GPS-PID controller |
uint8_t NaviGpsMinSat; // number of sattelites neccesary for GPS functions |
uint8_t NaviStickThreshold; // activation threshild for detection of manual stick movements |
uint8_t NaviWindCorrection; // streng of wind course correction |
uint8_t NaviSpeedCompensation; // D gain fefore position hold login |
uint8_t NaviOperatingRadius; // Radius limit in m around start position for GPS flights |
uint8_t NaviAngleLimitation; // limitation of attitude angle controlled by the gps algorithm |
uint8_t NaviPHLoginTime; // position hold logintimeout |
uint8_t ExternalControl; // for serial Control |
uint8_t BitConfig; // see upper defines for bitcoding |
uint8_t ServoNickCompInvert; // Wert : 0-250 0 oder 1 // WICHTIG!!! am Ende lassen |
uint8_t Reserved[4]; |
int8_t Name[12]; |
} paramset_t; |
|
#define PARAMSET_STRUCT_LEN sizeof(paramset_t) |
|
extern paramset_t ParamSet; |
|
extern void ParamSet_Init(void); |
extern void ParamSet_ReadFromEEProm(uint8_t setnumber); |
extern void ParamSet_WriteToEEProm(uint8_t setnumber); |
extern uint8_t GetActiveParamSet(void); |
extern void SetActiveParamSet(uint8_t setnumber); |
|
extern uint8_t MixerTable_ReadFromEEProm(void); |
extern uint8_t MixerTable_WriteToEEProm(void); |
|
|
extern uint8_t GetParamByte(uint16_t param_id); |
extern void SetParamByte(uint16_t param_id, uint8_t value); |
extern uint16_t GetParamWord(uint16_t param_id); |
extern void SetParamWord(uint16_t param_id, uint16_t value); |
|
|
#endif //_EEPROM_H |