Subversion Repositories Projects

Rev

Details | Last modification | View Log | RSS feed

Rev Author Line No. Line
428 killagreg 1
#include <inttypes.h>
2
#include <avr/io.h>
3
#include <avr/interrupt.h>
4
 
5
#include "timer0.h"
6
 
7
volatile uint16_t CountMilliseconds = 0;
8
DateTime_t SystemTime;
9
 
10
volatile uint16_t BeepTime = 0;
11
volatile uint16_t BeepModulation = 0xFFFF;
12
 
13
/*****************************************************/
14
/*              Initialize Timer 0                   */
15
/*****************************************************/
16
// timer 0 is used for the PWM generation to control the offset voltage at the air pressure sensor
17
// Its overflow interrupt routine is used to generate the beep signal and the flight control motor update rate
18
void TIMER0_Init(void)
19
{
20
        uint8_t sreg = SREG;
21
 
22
        // disable all interrupts before reconfiguration
23
        cli();
24
 
25
 
26
        // configure speaker port as output
27
 
28
        #ifdef USE_FOLLOWME
29
        // Speaker at PC7
30
        DDRC |= (1<<DDC7);
31
        PORTC &= ~(1<<PORTC7);
32
        #endif
33
 
34
        // Timer/Counter 0 Control Register A
35
 
36
        // Waveform Generation None (Bits WGM02 = 0, WGM01 = 0, WGM00 = 0)
37
    TCCR0A &= ~((1<<COM0A0)|(1<<COM0B0)|(1<<COM0A1)|(1<<COM0B1)|(1<<WGM01)|(1<<WGM00));
38
 
39
        // Timer/Counter 0 Control Register B
40
 
41
        // set clock devider for timer 0 to SYSKLOCK/8 = 20MHz / 8 = 2.5MHz
42
        // i.e. the timer increments from 0x00 to 0xFF with an update rate of 2.5 MHz
43
        // hence the timer overflow interrupt frequency is 2.5 MHz / 256 = 9.765 kHz
44
 
45
        // divider 8 (Bits CS02 = 0, CS01 = 1, CS00 = 0)
46
        TCCR0B &= ~((1<<FOC0A)|(1<<FOC0B)|(1<<WGM02));
47
    TCCR0B = (TCCR0B & 0xF8)|(0<<CS02)|(1<<CS01)|(0<<CS00);
48
 
49
        // init Timer/Counter 0 Register
50
    TCNT0 = 0;
51
 
52
        // Timer/Counter 0 Interrupt Mask Register
53
        // enable timer overflow interrupt only
54
        TIMSK0 &= ~((1<<OCIE0B)|(1<<OCIE0A));
55
        TIMSK0 |= (1<<TOIE0);
56
 
57
 
58
        SystemTime.Year = 0;
59
        SystemTime.Month = 0;
60
        SystemTime.Day = 0;
61
        SystemTime.Hour = 0;
62
        SystemTime.Min = 0;
63
        SystemTime.Sec = 0;
64
        SystemTime.mSec = 0;
65
        SystemTime.Valid = 0;
66
 
67
        CountMilliseconds = 0;
68
 
69
 
70
        SREG = sreg;
71
}
72
 
73
 
74
 
75
/*****************************************************/
76
/*          Interrupt Routine of Timer 0             */
77
/*****************************************************/
78
ISR(TIMER0_OVF_vect)    // 9.765 kHz
79
{
80
    static uint8_t cnt = 0;
81
    #ifdef USE_FOLLOWME
82
    uint8_t Beeper_On = 0;
83
        #endif
84
 
85
        if(!cnt--) // every 10th run (9.765kHz/10 = 976Hz)
86
        {
87
                cnt = 9;
88
                CountMilliseconds++; // increment millisecond counter
89
        }
90
 
91
        // beeper on if duration is not over
92
        if(BeepTime)
93
        {
94
                BeepTime--; // decrement BeepTime
95
                if(BeepTime & BeepModulation) Beeper_On = 1;
96
                else Beeper_On = 0;
97
        }
98
        else // beeper off if duration is over
99
        {
100
                Beeper_On = 0;
101
                BeepModulation = 0xFFFF;
102
        }
103
         #ifdef USE_FOLLOWME
104
        // if beeper is on
105
        if(Beeper_On)
106
        {
107
                // set speaker port to high
108
                PORTC |= (1<<PORTC7); // Speaker at PC7
109
        }
110
        else // beeper is off
111
        {
112
                // set speaker port to low
113
                PORTC &= ~(1<<PORTC7);// Speaker at PC7
114
        }
115
        #endif
116
}
117
 
118
 
119
// -----------------------------------------------------------------------
120
uint16_t SetDelay (uint16_t t)
121
{
122
  return(CountMilliseconds + t - 1);
123
}
124
 
125
// -----------------------------------------------------------------------
126
int8_t CheckDelay(uint16_t t)
127
{
128
  return(((t - CountMilliseconds) & 0x8000) >> 8); // check sign bit
129
}
130
 
131
// -----------------------------------------------------------------------
132
void Delay_ms(uint16_t w)
133
{
134
 unsigned int t_stop;
135
 t_stop = SetDelay(w);
136
 while (!CheckDelay(t_stop));
137
}
138