Rev 1657 | Go to most recent revision | Details | Compare with Previous | Last modification | View Log | RSS feed
Rev | Author | Line No. | Line |
---|---|---|---|
1 | ingob | 1 | #ifndef _I2C_MASTER_H |
2 | #define _I2C_MASTER_H |
||
1662 | killagreg | 3 | |
1 | ingob | 4 | |
1662 | killagreg | 5 | #include <inttypes.h> |
1 | ingob | 6 | |
1662 | killagreg | 7 | #define TWI_STATE_MOTOR_TX 0 |
8 | #define TWI_STATE_MOTOR_RX 5 |
||
9 | #define TWI_STATE_GYRO_OFFSET_TX 18 |
||
1 | ingob | 10 | |
1662 | killagreg | 11 | extern volatile uint8_t twi_state; |
12 | extern volatile uint8_t motor_write; |
||
13 | extern volatile uint8_t motor_read; |
||
1 | ingob | 14 | |
15 | |||
1662 | killagreg | 16 | extern uint8_t MissingMotor; |
17 | |||
1479 | killagreg | 18 | #define MAX_MOTORS 12 |
1638 | holgerb | 19 | #define MOTOR_STATE_PRESENT_MASK 0x80 |
20 | #define MOTOR_STATE_ERROR_MASK 0x7F |
||
1479 | killagreg | 21 | |
1638 | holgerb | 22 | #define MOTOR_STATE_NEW_PROTOCOL_MASK 0x01 |
23 | |||
1662 | killagreg | 24 | #define BLFLAG_TX_COMPLETE 0x01 |
25 | #define BLFLAG_READ_VERSION 0x02 |
||
1648 | killagreg | 26 | |
1662 | killagreg | 27 | extern volatile uint8_t BLFlags; |
1648 | killagreg | 28 | |
1479 | killagreg | 29 | typedef struct |
30 | { |
||
1662 | killagreg | 31 | uint8_t Version; // the version of the BL (0 = old) |
32 | uint8_t SetPoint; // written by attitude controller |
||
33 | uint8_t SetPointLowerBits; // for higher Resolution of new BLs |
||
34 | uint8_t State; // 7 bit for I2C error counter, highest bit indicates if motor is present |
||
35 | // the following bytes must be exactly in that order! |
||
36 | uint8_t Current; // in 0.1 A steps, read back from BL |
||
37 | uint8_t MaxPWM; // read back from BL is less than 255 if BL is in current limit |
||
38 | int8_t Temperature; // old BL-Ctrl will return a 255 here, the new version the temp. in °C |
||
1479 | killagreg | 39 | } __attribute__((packed)) MotorData_t; |
40 | |||
41 | extern MotorData_t Motor[MAX_MOTORS]; |
||
42 | |||
1662 | killagreg | 43 | #define BLCONFIG_REVISION 1 |
1 | ingob | 44 | |
1662 | killagreg | 45 | #define MASK_SET_PWM_SCALING 0x01 |
46 | #define MASK_SET_CURRENT_LIMIT 0x02 |
||
47 | #define MASK_SET_TEMP_LIMIT 0x04 |
||
48 | #define MASK_SET_CURRENT_SCALING 0x08 |
||
49 | #define MASK_SET_BITCONFIG 0x10 |
||
50 | #define MASK_RESET_CAPCOUNTER 0x20 |
||
51 | #define MASK_SET_DEFAULT_PARAMS 0x40 |
||
52 | #define MASK_SET_SAVE_EEPROM 0x80 |
||
1639 | holgerb | 53 | |
1662 | killagreg | 54 | #define BITCONF_REVERSE_ROTATION 0x01 |
55 | #define BITCONF_RES1 0x02 |
||
56 | #define BITCONF_RES2 0x04 |
||
57 | #define BITCONF_RES3 0x08 |
||
58 | #define BITCONF_RES4 0x10 |
||
59 | #define BITCONF_RES5 0x20 |
||
60 | #define BITCONF_RES6 0x40 |
||
61 | #define BITCONF_RES7 0x80 |
||
62 | |||
63 | typedef struct |
||
64 | { |
||
65 | uint8_t Revision; // must be BL_REVISION |
||
66 | uint8_t SetMask; // settings mask |
||
67 | uint8_t PwmScaling; // maximum value of control pwm, acts like a thrust limit |
||
68 | uint8_t CurrentLimit; // current limit in A |
||
69 | uint8_t TempLimit; // in °C |
||
70 | uint8_t CurrentScaling; // scaling factor for current measurement |
||
71 | uint8_t BitConfig; // see defines above |
||
72 | uint8_t crc; // checksum |
||
73 | } __attribute__((packed)) BLConfig_t; |
||
74 | |||
75 | extern BLConfig_t BLConfig; |
||
76 | |||
77 | extern volatile uint16_t I2CTimeout; |
||
78 | |||
79 | void I2C_Init (void); // Initialize I2C |
||
80 | #define I2C_Start(start_state) {twi_state = start_state; BLFlags &= ~BLFLAG_TX_COMPLETE; TWCR = (1<<TWSTA) | (1<<TWEN) | (1<<TWINT) | (1<<TWIE);} |
||
81 | #define I2C_Stop(start_state) {twi_state = start_state; TWCR = (1<<TWEN) | (1<<TWSTO) | (1<<TWINT);} |
||
82 | void I2C_Reset(void); // Reset I2C |
||
83 | uint8_t I2C_WriteBLConfig(uint8_t motor); |
||
84 | uint8_t I2C_ReadBLConfig(uint8_t motor); |
||
85 | |||
1 | ingob | 86 | #endif |