Rev 2300 | Details | Compare with Previous | Last modification | View Log | RSS feed
Rev | Author | Line No. | Line |
---|---|---|---|
2285 | - | 1 | // ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
2 | // + www.MikroKopter.com |
||
3 | // ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
||
4 | // + Software Nutzungsbedingungen (english version: see below) |
||
5 | // + der Fa. HiSystems GmbH, Flachsmeerstrasse 2, 26802 Moormerland - nachfolgend Lizenzgeber genannt - |
||
6 | // + Der Lizenzgeber räumt dem Kunden ein nicht-ausschließliches, zeitlich und räumlich* unbeschränktes Recht ein, die im den |
||
7 | // + Mikrocontroller verwendete Firmware für die Hardware Flight-Ctrl, Navi-Ctrl, BL-Ctrl, MK3Mag & PC-Programm MikroKopter-Tool |
||
8 | // + - nachfolgend Software genannt - nur für private Zwecke zu nutzen. |
||
9 | // + Der Einsatz dieser Software ist nur auf oder mit Produkten des Lizenzgebers zulässig. |
||
10 | // ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
||
11 | // + Die vom Lizenzgeber gelieferte Software ist urheberrechtlich geschützt. Alle Rechte an der Software sowie an sonstigen im |
||
12 | // + Rahmen der Vertragsanbahnung und Vertragsdurchführung überlassenen Unterlagen stehen im Verhältnis der Vertragspartner ausschließlich dem Lizenzgeber zu. |
||
13 | // + Die in der Software enthaltenen Copyright-Vermerke, Markenzeichen, andere Rechtsvorbehalte, Seriennummern sowie |
||
14 | // + sonstige der Programmidentifikation dienenden Merkmale dürfen vom Kunden nicht verändert oder unkenntlich gemacht werden. |
||
15 | // + Der Kunde trifft angemessene Vorkehrungen für den sicheren Einsatz der Software. Er wird die Software gründlich auf deren |
||
16 | // + Verwendbarkeit zu dem von ihm beabsichtigten Zweck testen, bevor er diese operativ einsetzt. |
||
17 | // + Die Haftung des Lizenzgebers wird - soweit gesetzlich zulässig - begrenzt in Höhe des typischen und vorhersehbaren |
||
18 | // + Schadens. Die gesetzliche Haftung bei Personenschäden und nach dem Produkthaftungsgesetz bleibt unberührt. Dem Lizenzgeber steht jedoch der Einwand |
||
19 | // + des Mitverschuldens offen. |
||
20 | // + Der Kunde trifft angemessene Vorkehrungen für den Fall, dass die Software ganz oder teilweise nicht ordnungsgemäß arbeitet. |
||
21 | // + Er wird die Software gründlich auf deren Verwendbarkeit zu dem von ihm beabsichtigten Zweck testen, bevor er diese operativ einsetzt. |
||
22 | // + Der Kunde wird er seine Daten vor Einsatz der Software nach dem Stand der Technik sichern. |
||
23 | // + Der Kunde ist darüber unterrichtet, dass der Lizenzgeber seine Daten im zur Vertragsdurchführung erforderlichen Umfang |
||
24 | // + und auf Grundlage der Datenschutzvorschriften erhebt, speichert, verarbeitet und, sofern notwendig, an Dritte übermittelt. |
||
25 | // + *) Die räumliche Nutzung bezieht sich nur auf den Einsatzort, nicht auf die Reichweite der programmierten Software. |
||
26 | // + #### ENDE DER NUTZUNGSBEDINGUNGEN ####' |
||
27 | // + Hinweis: Informationen über erweiterte Nutzungsrechte (wie z.B. Nutzung für nicht-private Zwecke) sind auf Anfrage per Email an info(@)hisystems.de verfügbar. |
||
28 | // ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
||
29 | // + Software LICENSING TERMS |
||
30 | // ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
||
31 | // + of HiSystems GmbH, Flachsmeerstrasse 2, 26802 Moormerland, Germany - the Licensor - |
||
32 | // + The Licensor grants the customer a non-exclusive license to use the microcontroller firmware of the Flight-Ctrl, Navi-Ctrl, BL-Ctrl, and MK3Mag hardware |
||
33 | // + (the Software) exclusively for private purposes. The License is unrestricted with respect to time and territory*. |
||
34 | // + The Software may only be used with the Licensor's products. |
||
35 | // + The Software provided by the Licensor is protected by copyright. With respect to the relationship between the parties to this |
||
36 | // + agreement, all rights pertaining to the Software and other documents provided during the preparation and execution of this |
||
37 | // + agreement shall be the property of the Licensor. |
||
38 | // + The information contained in the Software copyright notices, trademarks, other legal reservations, serial numbers and other |
||
39 | // + features that can be used to identify the program may not be altered or defaced by the customer. |
||
40 | // + The customer shall be responsible for taking reasonable precautions |
||
41 | // + for the safe use of the Software. The customer shall test the Software thoroughly regarding its suitability for the |
||
42 | // + intended purpose before implementing it for actual operation. The Licensor's liability shall be limited to the extent of typical and |
||
43 | // + foreseeable damage to the extent permitted by law, notwithstanding statutory liability for bodily injury and product |
||
44 | // + liability. However, the Licensor shall be entitled to the defense of contributory negligence. |
||
45 | // + The customer will take adequate precautions in the case, that the software is not working properly. The customer will test |
||
46 | // + the software for his purpose before any operational usage. The customer will backup his data before using the software. |
||
47 | // + The customer understands that the Licensor collects, stores and processes, and, where required, forwards, customer data |
||
48 | // + to third parties to the extent necessary for executing the agreement, subject to applicable data protection and privacy regulations. |
||
49 | // + *) The territory aspect only refers to the place where the Software is used, not its programmed range. |
||
50 | // + #### END OF LICENSING TERMS #### |
||
51 | // + Note: For information on license extensions (e.g. commercial use), please contact us at info(@)hisystems.de. |
||
52 | // ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
||
53 | |||
54 | #include "main.h" |
||
55 | #define MULTIPLYER 4 |
||
56 | |||
57 | volatile unsigned int CountMilliseconds = 0; |
||
58 | volatile unsigned int tim_main; |
||
59 | volatile unsigned char UpdateMotor = 0; |
||
60 | volatile unsigned int cntKompass = 0; |
||
61 | volatile unsigned int beeptime = 0; |
||
62 | volatile unsigned char SendSPI = 0, ServoActive = 0, CalculateServoSignals = 1; |
||
63 | uint16_t RemainingPulse = 0; |
||
64 | volatile int16_t ServoNickOffset = (255 / 2) * MULTIPLYER * 16; // initial value near center positon |
||
65 | volatile int16_t ServoRollOffset = (255 / 2) * MULTIPLYER * 16; // initial value near center positon |
||
66 | |||
67 | unsigned int BeepMuster = 0xffff; |
||
68 | signed int NickServoValue = 128 * MULTIPLYER * 16; |
||
69 | |||
70 | volatile int16_t ServoNickValue = 0; |
||
71 | volatile int16_t ServoRollValue = 0; |
||
72 | |||
73 | |||
74 | enum { |
||
75 | STOP = 0, |
||
76 | CK = 1, |
||
77 | CK8 = 2, |
||
78 | CK64 = 3, |
||
79 | CK256 = 4, |
||
80 | CK1024 = 5, |
||
81 | T0_FALLING_EDGE = 6, |
||
82 | T0_RISING_EDGE = 7 |
||
83 | }; |
||
84 | |||
85 | |||
86 | ISR(TIMER0_OVF_vect) // 9,7kHz |
||
87 | { |
||
88 | static unsigned char cnt_1ms = 1,cnt = 0, compass_active = 0; |
||
89 | unsigned char pieper_ein = 0; |
||
90 | if(SendSPI) SendSPI--; |
||
91 | if(SpektrumTimer) SpektrumTimer--; |
||
92 | if(!cnt--) |
||
93 | { |
||
94 | cnt = 9; |
||
95 | CountMilliseconds++; |
||
96 | cnt_1ms++; |
||
97 | cnt_1ms %= 2; |
||
98 | |||
99 | if(!cnt_1ms) UpdateMotor = 1; |
||
100 | if(!(PINC & 0x10)) compass_active = 1; |
||
101 | |||
102 | if(beeptime) |
||
103 | { |
||
104 | if(beeptime > 10) beeptime -= 10; else beeptime = 0; |
||
105 | if(beeptime & BeepMuster) |
||
106 | { |
||
107 | pieper_ein = 1; |
||
108 | } |
||
109 | else pieper_ein = 0; |
||
110 | } |
||
111 | else |
||
112 | { |
||
113 | pieper_ein = 0; |
||
114 | BeepMuster = 0xffff; |
||
115 | } |
||
116 | if(pieper_ein) |
||
117 | { |
||
118 | if(PlatinenVersion == 10) PORTD |= (1<<2); // Speaker an PORTD.2 |
||
119 | else PORTC |= (1<<7); // Speaker an PORTC.7 |
||
120 | } |
||
121 | else |
||
122 | { |
||
123 | if(PlatinenVersion == 10) PORTD &= ~(1<<2); |
||
124 | else PORTC &= ~(1<<7); |
||
125 | } |
||
126 | } |
||
127 | if(compass_active && !NaviDataOkay && Parameter_GlobalConfig & CFG_KOMPASS_AKTIV) |
||
128 | { |
||
129 | if(PINC & 0x10) |
||
130 | { |
||
131 | if(++cntKompass > 1000) compass_active = 0; |
||
132 | } |
||
133 | else |
||
134 | { |
||
135 | if((cntKompass) && (cntKompass < 362)) |
||
136 | { |
||
137 | cntKompass += cntKompass / 41; |
||
138 | if(cntKompass > 10) KompassValue = cntKompass - 10; else KompassValue = 0; |
||
139 | // KompassRichtung = ((540 + KompassValue - KompassSollWert) % 360) - 180; |
||
140 | } |
||
141 | cntKompass = 0; |
||
142 | } |
||
143 | } |
||
144 | } |
||
145 | |||
146 | |||
147 | // ----------------------------------------------------------------------- |
||
148 | unsigned int SetDelay(unsigned int t) |
||
149 | { |
||
150 | // TIMSK0 &= ~_BV(TOIE0); |
||
151 | return(CountMilliseconds + t + 1); |
||
152 | // TIMSK0 |= _BV(TOIE0); |
||
153 | } |
||
154 | |||
155 | // ----------------------------------------------------------------------- |
||
156 | char CheckDelay(unsigned int t) |
||
157 | { |
||
158 | // TIMSK0 &= ~_BV(TOIE0); |
||
159 | return(((t - CountMilliseconds) & 0x8000) >> 9); |
||
160 | // TIMSK0 |= _BV(TOIE0); |
||
161 | } |
||
162 | |||
163 | // ----------------------------------------------------------------------- |
||
164 | void Delay_ms(unsigned int w) |
||
165 | { |
||
166 | unsigned int akt; |
||
167 | akt = SetDelay(w); |
||
168 | while (!CheckDelay(akt)); |
||
169 | } |
||
170 | |||
171 | void Delay_ms_Mess(unsigned int w) |
||
172 | { |
||
173 | unsigned int akt; |
||
174 | akt = SetDelay(w); |
||
175 | while (!CheckDelay(akt)) if(AdReady) {AdReady = 0; ANALOG_ON;} |
||
176 | } |
||
177 | |||
178 | /*****************************************************/ |
||
179 | /* Initialize Timer 2 */ |
||
180 | /*****************************************************/ |
||
181 | // The timer 2 is used to generate the PWM at PD7 (J7) |
||
182 | // to control a camera servo for nick compensation. |
||
183 | void TIMER2_Init(void) |
||
184 | { |
||
185 | uint8_t sreg = SREG; |
||
186 | |||
187 | // disable all interrupts before reconfiguration |
||
188 | cli(); |
||
189 | |||
190 | PORTD &= ~(1<<PORTD7); // set PD7 to low |
||
191 | |||
192 | DDRC |= (1<<DDC6); // set PC6 as output (Reset for HEF4017) |
||
193 | HEF4017Reset_ON; |
||
194 | // Timer/Counter 2 Control Register A |
||
195 | |||
196 | // Timer Mode is FastPWM with timer reload at OCR2A (Bits: WGM22 = 1, WGM21 = 1, WGM20 = 1) |
||
197 | // PD7: Normal port operation, OC2A disconnected, (Bits: COM2A1 = 0, COM2A0 = 0) |
||
198 | // PD6: Normal port operation, OC2B disconnected, (Bits: COM2B1 = 0, COM2B0 = 0) |
||
199 | TCCR2A &= ~((1<<COM2A1)|(1<<COM2A0)|(1<<COM2B1)|(1<<COM2B0)); |
||
200 | TCCR2A |= (1<<WGM21)|(1<<WGM20); |
||
201 | |||
202 | // Timer/Counter 2 Control Register B |
||
203 | |||
204 | // Set clock divider for timer 2 to SYSKLOCK/32 = 20MHz / 32 = 625 kHz |
||
205 | // The timer increments from 0x00 to 0xFF with an update rate of 625 kHz or 1.6 us |
||
206 | // hence the timer overflow interrupt frequency is 625 kHz / 256 = 2.44 kHz or 0.4096 ms |
||
207 | |||
208 | // divider 32 (Bits: CS022 = 0, CS21 = 1, CS20 = 1) |
||
209 | TCCR2B &= ~((1<<FOC2A)|(1<<FOC2B)|(1<<CS22)); |
||
210 | TCCR2B |= (1<<CS21)|(1<<CS20)|(1<<WGM22); |
||
211 | |||
212 | // Initialize the Timer/Counter 2 Register |
||
213 | TCNT2 = 0; |
||
214 | |||
215 | // Initialize the Output Compare Register A used for PWM generation on port PD7. |
||
216 | OCR2A = 255; |
||
217 | TCCR2A |= (1<<COM2A1); // set or clear at compare match depends on value of COM2A0 |
||
218 | |||
219 | // Timer/Counter 2 Interrupt Mask Register |
||
220 | // Enable timer output compare match A Interrupt only |
||
221 | TIMSK2 &= ~((1<<OCIE2B)|(1<<TOIE2)); |
||
222 | TIMSK2 |= (1<<OCIE2A); |
||
223 | |||
224 | SREG = sreg; |
||
225 | } |
||
226 | |||
227 | //---------------------------- |
||
228 | void Timer_Init(void) |
||
229 | { |
||
230 | tim_main = SetDelay(10); |
||
231 | TCCR0B = CK8; |
||
232 | TCCR0A = (1<<COM0A1)|(1<<COM0B1)|3;//fast PWM |
||
233 | OCR0A = 0; |
||
234 | OCR0B = 180; |
||
235 | TCNT0 = (unsigned char)-TIMER_RELOAD_VALUE; // reload |
||
236 | //OCR1 = 0x00; |
||
237 | TIMSK0 |= _BV(TOIE0); |
||
238 | } |
||
239 | |||
240 | |||
241 | /*****************************************************/ |
||
242 | /* Control Servo Position */ |
||
243 | /*****************************************************/ |
||
244 | void CalcNickServoValue(void) |
||
245 | { |
||
246 | signed int max, min; |
||
247 | |||
248 | if(EE_Parameter.ServoCompInvert & SERVO_RELATIVE) // relative moving of the servo value |
||
249 | { |
||
250 | max = ((unsigned int) EE_Parameter.ServoNickMax * MULTIPLYER * 15); |
||
251 | min = ((unsigned int) EE_Parameter.ServoNickMin * MULTIPLYER * 20); |
||
252 | NickServoValue -= ((signed char) (Parameter_ServoNickControl - 128) / 4) * 6; |
||
253 | LIMIT_MIN_MAX(NickServoValue,min, max); |
||
254 | } |
||
255 | else NickServoValue = (int16_t)Parameter_ServoNickControl * (MULTIPLYER*16); // direct poti control |
||
256 | } |
||
257 | |||
258 | void CalculateServo(void) |
||
259 | { |
||
260 | signed char cosinus, sinus; |
||
261 | signed long nick, roll; |
||
262 | |||
263 | cosinus = sintab[EE_Parameter.CamOrientation + 6]; |
||
264 | sinus = sintab[EE_Parameter.CamOrientation]; |
||
265 | |||
266 | if(CalculateServoSignals == 1) |
||
267 | { |
||
268 | nick = (cosinus * IntegralNick) / 128L - (sinus * IntegralRoll) / 128L; |
||
269 | nick -= POI_KameraNick * 7; |
||
270 | nick = ((long)EE_Parameter.ServoNickComp * nick) / 512L; |
||
271 | // offset (Range from 0 to 255 * 3 = 765) |
||
272 | if(EE_Parameter.ServoCompInvert & SERVO_RELATIVE) ServoNickOffset = NickServoValue; |
||
273 | else ServoNickOffset += (NickServoValue - ServoNickOffset) / EE_Parameter.ServoManualControlSpeed; |
||
274 | |||
275 | if(EE_Parameter.ServoCompInvert & SERVO_NICK_INV) // inverting movement of servo |
||
276 | { |
||
277 | nick = ServoNickOffset / 16 + nick; |
||
278 | } |
||
279 | else |
||
280 | { // inverting movement of servo |
||
281 | nick = ServoNickOffset / 16 - nick; |
||
282 | } |
||
283 | if(EE_Parameter.ServoFilterNick) ServoNickValue = ((ServoNickValue * EE_Parameter.ServoFilterNick) + nick) / (EE_Parameter.ServoFilterNick + 1); |
||
284 | else ServoNickValue = nick; |
||
285 | // limit servo value to its parameter range definition |
||
286 | if(ServoNickValue < ((int16_t)EE_Parameter.ServoNickMin * MULTIPLYER)) |
||
287 | { |
||
288 | ServoNickValue = (int16_t)EE_Parameter.ServoNickMin * MULTIPLYER; |
||
289 | } |
||
290 | else |
||
291 | if(ServoNickValue > ((int16_t)EE_Parameter.ServoNickMax * MULTIPLYER)) |
||
292 | { |
||
293 | ServoNickValue = (int16_t)EE_Parameter.ServoNickMax * MULTIPLYER; |
||
294 | } |
||
295 | if(PlatinenVersion < 20) CalculateServoSignals = 0; else CalculateServoSignals++; |
||
296 | } |
||
297 | else |
||
298 | { |
||
299 | roll = (cosinus * IntegralRoll) / 128L + (sinus * IntegralNick) / 128L; |
||
300 | roll = ((long)EE_Parameter.ServoRollComp * roll) / 512L; |
||
301 | ServoRollOffset += ((int16_t)Parameter_ServoRollControl * (MULTIPLYER*16) - ServoRollOffset) / EE_Parameter.ServoManualControlSpeed; |
||
302 | if(EE_Parameter.ServoCompInvert & SERVO_ROLL_INV) |
||
303 | { // inverting movement of servo |
||
304 | roll = ServoRollOffset / 16 + roll; |
||
305 | } |
||
306 | else |
||
307 | { // inverting movement of servo |
||
308 | roll = ServoRollOffset / 16 - roll; |
||
309 | } |
||
310 | if(EE_Parameter.ServoFilterRoll) ServoRollValue = ((ServoRollValue * EE_Parameter.ServoFilterRoll) + roll) / (EE_Parameter.ServoFilterRoll + 1); |
||
311 | else ServoRollValue = roll; |
||
312 | // limit servo value to its parameter range definition |
||
313 | if(ServoRollValue < ((int16_t)EE_Parameter.ServoRollMin * MULTIPLYER)) |
||
314 | { |
||
315 | ServoRollValue = (int16_t)EE_Parameter.ServoRollMin * MULTIPLYER; |
||
316 | } |
||
317 | else |
||
318 | if(ServoRollValue > ((int16_t)EE_Parameter.ServoRollMax * MULTIPLYER)) |
||
319 | { |
||
320 | ServoRollValue = (int16_t)EE_Parameter.ServoRollMax * MULTIPLYER; |
||
321 | } |
||
322 | CalculateServoSignals = 0; |
||
323 | } |
||
324 | } |
||
325 | |||
326 | ISR(TIMER2_COMPA_vect) |
||
327 | { |
||
328 | // frame len 22.5 ms = 14063 * 1.6 us |
||
329 | // stop pulse: 0.3 ms = 188 * 1.6 us |
||
330 | // min servo pulse: 0.6 ms = 375 * 1.6 us |
||
331 | // max servo pulse: 2.4 ms = 1500 * 1.6 us |
||
332 | // resolution: 1500 - 375 = 1125 steps |
||
333 | |||
334 | #define IRS_RUNTIME 127 |
||
335 | #define PPM_STOPPULSE 188 |
||
336 | #define PPM_FRAMELEN (1757 * EE_Parameter.ServoNickRefresh) |
||
337 | #define MINSERVOPULSE 375 |
||
338 | #define MAXSERVOPULSE 1500 |
||
339 | #define SERVORANGE (MAXSERVOPULSE - MINSERVOPULSE) |
||
340 | |||
341 | static uint8_t PulseOutput = 0; |
||
342 | static uint16_t ServoFrameTime = 0; |
||
343 | static uint8_t ServoIndex = 0; |
||
344 | |||
345 | |||
346 | if(PlatinenVersion < 20) |
||
347 | { |
||
348 | //--------------------------- |
||
349 | // Nick servo state machine |
||
350 | //--------------------------- |
||
351 | if(!PulseOutput) // pulse output complete |
||
352 | { |
||
353 | if(TCCR2A & (1<<COM2A0)) // we had a low pulse |
||
354 | { |
||
355 | TCCR2A &= ~(1<<COM2A0);// make a high pulse |
||
356 | RemainingPulse = MINSERVOPULSE + SERVORANGE/2; // center position ~ 1.5ms |
||
357 | RemainingPulse += ServoNickValue - (256 / 2) * MULTIPLYER; // shift ServoNickValue to center position |
||
358 | // range servo pulse width |
||
359 | if(RemainingPulse > MAXSERVOPULSE ) RemainingPulse = MAXSERVOPULSE; // upper servo pulse limit |
||
360 | else if(RemainingPulse < MINSERVOPULSE ) RemainingPulse = MINSERVOPULSE; // lower servo pulse limit |
||
361 | // accumulate time for correct update rate |
||
362 | ServoFrameTime = RemainingPulse; |
||
363 | } |
||
364 | else // we had a high pulse |
||
365 | { |
||
366 | TCCR2A |= (1<<COM2A0); // make a low pulse |
||
367 | RemainingPulse = PPM_FRAMELEN - ServoFrameTime; |
||
368 | CalculateServoSignals = 1; |
||
369 | } |
||
370 | // set pulse output active |
||
371 | PulseOutput = 1; |
||
372 | } |
||
373 | } // EOF Nick servo state machine |
||
374 | else |
||
375 | { |
||
376 | //----------------------------------------------------- |
||
377 | // PPM state machine, onboard demultiplexed by HEF4017 |
||
378 | //----------------------------------------------------- |
||
379 | if(!PulseOutput) // pulse output complete |
||
380 | { |
||
381 | if(TCCR2A & (1<<COM2A0)) // we had a low pulse |
||
382 | { |
||
383 | TCCR2A &= ~(1<<COM2A0);// make a high pulse |
||
384 | if(ServoIndex == 0) // if we are at the sync gap |
||
385 | { |
||
386 | RemainingPulse = PPM_FRAMELEN - ServoFrameTime; // generate sync gap by filling time to full frame time |
||
387 | ServoFrameTime = 0; // reset servo frame time |
||
388 | HEF4017Reset_ON; // enable HEF4017 reset |
||
389 | } |
||
390 | else // servo channels |
||
391 | if(ServoIndex > EE_Parameter.ServoNickRefresh) |
||
392 | { |
||
393 | RemainingPulse = 10; // end it here |
||
394 | } |
||
395 | else |
||
396 | { |
||
397 | RemainingPulse = MINSERVOPULSE + SERVORANGE/2; // center position ~ 1.5ms |
||
398 | switch(ServoIndex) // map servo channels |
||
399 | { |
||
400 | case 1: // Nick Compensation Servo |
||
401 | RemainingPulse += ServoNickValue - (256 / 2) * MULTIPLYER; // shift ServoNickValue to center position |
||
402 | break; |
||
403 | case 2: // Roll Compensation Servo |
||
404 | RemainingPulse += ServoRollValue - (256 / 2) * MULTIPLYER; // shift ServoNickValue to center position |
||
405 | break; |
||
406 | case 3: |
||
407 | RemainingPulse += ((int16_t)Parameter_Servo3 * MULTIPLYER) - (256 / 2) * MULTIPLYER; |
||
408 | break; |
||
409 | case 4: |
||
410 | RemainingPulse += ((int16_t)Parameter_Servo4 * MULTIPLYER) - (256 / 2) * MULTIPLYER; |
||
411 | break; |
||
412 | case 5: |
||
413 | RemainingPulse += ((int16_t)Parameter_Servo5 * MULTIPLYER) - (256 / 2) * MULTIPLYER; |
||
414 | break; |
||
415 | default: // other servo channels |
||
416 | RemainingPulse += 2 * PPM_in[ServoIndex]; // add channel value, factor of 2 because timer 1 increments 3.2µs |
||
417 | break; |
||
418 | } |
||
419 | // range servo pulse width |
||
420 | if(RemainingPulse > MAXSERVOPULSE) RemainingPulse = MAXSERVOPULSE; // upper servo pulse limit |
||
421 | else if(RemainingPulse < MINSERVOPULSE) RemainingPulse = MINSERVOPULSE; // lower servo pulse limit |
||
422 | // substract stop pulse width |
||
423 | RemainingPulse -= PPM_STOPPULSE; |
||
424 | // accumulate time for correct sync gap |
||
425 | ServoFrameTime += RemainingPulse; |
||
426 | } |
||
427 | } |
||
428 | else // we had a high pulse |
||
429 | { |
||
430 | TCCR2A |= (1<<COM2A0); // make a low pulse |
||
431 | // set pulsewidth to stop pulse width |
||
432 | RemainingPulse = PPM_STOPPULSE; |
||
433 | // accumulate time for correct sync gap |
||
434 | ServoFrameTime += RemainingPulse; |
||
435 | if((ServoActive && SenderOkay) || ServoActive == 2) HEF4017Reset_OFF; // disable HEF4017 reset |
||
436 | else HEF4017Reset_ON; |
||
437 | ServoIndex++; |
||
438 | if(ServoIndex > EE_Parameter.ServoNickRefresh+1) |
||
439 | { |
||
440 | CalculateServoSignals = 1; |
||
441 | ServoIndex = 0; // reset to the sync gap |
||
442 | } |
||
443 | } |
||
444 | // set pulse output active |
||
445 | PulseOutput = 1; |
||
446 | } |
||
447 | } // EOF PPM state machine |
||
448 | |||
449 | // General pulse output generator |
||
450 | if(RemainingPulse > (255 + IRS_RUNTIME)) |
||
451 | { |
||
452 | OCR2A = 255; |
||
453 | RemainingPulse -= 255; |
||
454 | } |
||
455 | else |
||
456 | { |
||
457 | if(RemainingPulse > 255) // this is the 2nd last part |
||
458 | { |
||
459 | if((RemainingPulse - 255) < IRS_RUNTIME) |
||
460 | { |
||
461 | OCR2A = 255 - IRS_RUNTIME; |
||
462 | RemainingPulse -= 255 - IRS_RUNTIME; |
||
463 | |||
464 | } |
||
465 | else // last part > ISR_RUNTIME |
||
466 | { |
||
467 | OCR2A = 255; |
||
468 | RemainingPulse -= 255; |
||
469 | } |
||
470 | } |
||
471 | else // this is the last part |
||
472 | { |
||
473 | OCR2A = RemainingPulse; |
||
474 | RemainingPulse = 0; |
||
475 | PulseOutput = 0; // trigger to stop pulse |
||
476 | } |
||
477 | } // EOF general pulse output generator |
||
478 | } |