Subversion Repositories FlightCtrl

#ifndef _OUTPUT_H

#define _OUTPUT_H

#include <avr/io.h>

#define J3HIGH    PORTD |= (1<<PORTD5)

#define J3LOW     PORTD &= ~(1<<PORTD5)

#define J3TOGGLE  PORTD ^= (1<<PORTD5)

#define J4HIGH    PORTD |= (1<<PORTD4)

#define J4LOW     PORTD &= ~(1<<PORTD4)

#define J4TOGGLE  PORTD ^= (1<<PORTD4)

#define J5HIGH    PORTD |= (1<<PORTD3)

#define J5LOW     PORTD &= ~(1<<PORTD3)

#define J5TOGGLE  PORTD ^= (1<<PORTD3)

// invert means: An "1" bit in digital debug data make a LOW on the output.

#define DIGITAL_DEBUG_INVERT 0

#define OUTPUT_HIGH(num)        {PORTC |=  (4 << (num));}

#define OUTPUT_LOW(num)         {PORTC &= ~(4 << (num));}

#define OUTPUT_TOGGLE(num) (    {PORTC ^=  (4 << (num));}

/*

 * Some digital debugs. A digital debug is 2 signals on the 2 LED outputs,

 * turned on and off depending on some condtions given in the code.

 * Only one can be selected, by defining DIGITAL_DEBUG_MASK to the value

 * of the debug.

 * In the code one can do like:

 * if (whatever_condition) {

 *      DebugOut.Digital[0] |= DEBUG_MYOWNDEBUGGER;

 * } else {

 *      DebugOut.Digital[0] &= ~DEBUG_MYOWNDEBUGGER;

 * }

 * ...

 * if (whatever_other_condition) {

 *      DebugOut.Digital[1] |= DEBUG_MYOWNDEBUGGER;

 * } else {

 *      DebugOut.Digital[1] &= ~DEBUG_MYOWNDEBUGGER;

 * }

 *

 * Digital debugs may be added as desired, and removed when the mystery

 * at hand is resolved.

 */

#define DEBUG_MAINLOOP_TIMER 1

#define DEBUG_HEIGHT_DIFF    2

#define DEBUG_HOVERTHROTTLE  4

#define DEBUG_ACC0THORDER    8

#define DEBUG_COMPASS       16

#define DEBUG_PRESSURERANGE 32

#define DEBUG_CLIP          64

#define DEBUG_SENSORLIMIT  128

#define OUTPUTFLAGS_INVERT_0         1 // Inverted: 1 means low output on atmega. Does not affect on-board LED (if used with the OUTPUTOPTIONS_USE_ONBOARD_LEDS option)

#define OUTPUTFLAGS_INVERT_1         2 // Inverted: 1 means low output on atmega. Does not affect on-board LED (if used with the OUTPUTOPTIONS_USE_ONBOARD_LEDS option)

#define OUTPUTFLAGS_FLASH_0_AT_BEEP  4 // Flash LED when beeper beeps

#define OUTPUTFLAGS_FLASH_1_AT_BEEP  8 // Flash LED when beeper beeps

#define OUTPUTFLAGS_USE_ONBOARD_LEDS 16 // Control on-board LEDs in addition to outputs

#define OUTPUTFLAGS_TEST_OFF         32 // For testing: Turn off both outputs

#define OUTPUTFLAGS_TEST_ON          64 // For testing: Turn on both outputs

/*

 * Set to 0 for using outputs as the usual flashing lights.

 * Set to one of the DEBUG_... defines h for using the outputs as debug lights.

 */

#define DIGITAL_DEBUG_MASK 0

void output_init(void);

void outputSet(uint8_t num, uint8_t state);

void output_update(void);

void beep(uint16_t millis);

void beepNumber(uint8_t numbeeps);

void beepRCAlarm(void);

void beepI2CAlarm(void);

void beepBatteryAlarm(void);

#endif //_output_H