Subversion Repositories FlightCtrl

#include <inttypes.h>

#include <avr/io.h>

#include <avr/interrupt.h>

#include <avr/wdt.h>

#include "eeprom.h"

#include "analog.h"

#include "controlMixer.h"

#include "timer0.h"

#include "output.h"

#ifdef DO_PROFILE

volatile uint32_t global10kHzClock = 0;

volatile int32_t profileTimers[NUM_PROFILE_TIMERS];

volatile int32_t runningProfileTimers[NUM_PROFILE_TIMERS];

#endif

volatile uint32_t globalMillisClock = 0;

volatile uint8_t  runFlightControl = 0;

volatile uint16_t beepTime = 0;

volatile uint16_t beepModulation = BEEP_MODULATION_NONE;

/*****************************************************

 * Initialize Timer 0                  

 *****************************************************/

// timer 0 is used for the PWM generation to control the offset voltage at the air pressure sensor

// Its overflow interrupt routine is used to generate the beep signal and the flight control motor update rate

void timer0_init(void) {

  uint8_t sreg = SREG;

  // disable all interrupts before reconfiguration

  cli();

  // Configure speaker port as output and also the diags pin D2

  DDRD |= ((1 << DDD5) | (1 << DDD2));

  PORTD &= ~((1 << PORTD5) | (1 << DDD2));

  // Timer/Counter 0 Control Register A

  // Waveform Generation Mode is Fast PWM (Bits WGM02 = 0, WGM01 = 1, WGM00 = 1)

  // Clear OC0A on Compare Match, set OC0A at BOTTOM, noninverting PWM (Bits COM0A1 = 1, COM0A0 = 0)

  // Clear OC0B on Compare Match, set OC0B at BOTTOM, (Bits COM0B1 = 1, COM0B0 = 0)

  // TCCR0A &= ~((1 << COM0A0) | (1 << COM0B0));

  // TCCR0A |= (1 << COM0A1) | (1 << COM0B1) | (1 << WGM01) | (1 << WGM00);

  // Timer/Counter 0 Control Register B

  // set clock divider for timer 0 to SYSCLOCK/8 = 20MHz/8 = 2.5MHz

  // i.e. the timer increments from 0x00 to 0xFF with an update rate of 2.5 MHz

  // hence the timer overflow interrupt frequency is 2.5 MHz/256 = 9.765 kHz

  // divider 8 (Bits CS02 = 0, CS01 = 1, CS00 = 0)

  TCCR0B &= ~((1 << FOC0A) | (1 << FOC0B) | (1 << WGM02));

  TCCR0B = (TCCR0B & 0xF8) | (0 << CS02) | (1 << CS01) | (0 << CS00);

  // initialize the Output Compare Register A & B used for PWM generation on port PB3 & PB4

  OCR0A = 0;    // for PB3

  OCR0B = 120;  // for PB4

  // init Timer/Counter 0 Register

  TCNT0 = 0;

  // Timer/Counter 0 Interrupt Mask Register

  // enable timer overflow interrupt only

  TIMSK0 &= ~((1 << OCIE0B) | (1 << OCIE0A));

  TIMSK0 |= (1 << TOIE0);

#ifdef DO_PROFILE

  for (uint8_t i=0; i<NUM_PROFILE_TIMERS; i++) {

          profileTimers[i] = 0;

  }

#endif

  SREG = sreg;

}

/*****************************************************/

/*          Interrupt Routine of Timer 0             */

/*****************************************************/

ISR(TIMER0_OVF_vect) { // 9765.625 Hz

  static uint8_t cnt_1ms = 1, cnt = 0;

  uint8_t beeperOn = 0;

#ifdef DO_PROFILE

    global10kHzClock++;

#endif

  if (!cnt--) { // every 10th run (9.765625kHz/10 = 976.5625Hz)

    cnt = 9;

    cnt_1ms ^= 1;

    if (!cnt_1ms) {

      runFlightControl = 1; // every 2nd run (976.5625 Hz/2 = 488.28125 Hz)

    }

    globalMillisClock++; // increment millisecond counter

  }

  // beeper on if duration is not over

  if (beepTime) {

    beepTime--; // decrement BeepTime

    if (beepTime & beepModulation)

      beeperOn = 1;

    else

      beeperOn = 0;

  } else { // beeper off if duration is over

    beeperOn = 0;

    beepModulation = BEEP_MODULATION_NONE;

  }

  if (beeperOn) {

    // set speaker port to high.

      PORTD |= (1 << PORTD5); // Speaker at PD5

  } else { // beeper is off

    // set speaker port to low

      PORTD &= ~(1 << PORTD5);// Speaker at PD5

  }

#ifdef USE_MK3MAG

  // update compass value if this option is enabled in the settings

  if (staticParams.bitConfig & CFG_COMPASS_ENABLED) {

    MK3MAG_periodicTask(); // read out mk3mag pwm

  }

#endif

}

// -----------------------------------------------------------------------

uint16_t setDelay(uint16_t t) {

  return (globalMillisClock + t - 1);

}

// -----------------------------------------------------------------------

int8_t checkDelay(uint16_t t) {

  return (((t - globalMillisClock) & 0x8000) >> 8); // check sign bit

}

// -----------------------------------------------------------------------

void delay_ms(uint16_t w) {

  uint16_t t_stop = setDelay(w);

  while (!checkDelay(t_stop))

        wdt_reset();

}

// -----------------------------------------------------------------------

void delay_ms_with_adc_measurement(uint16_t w, uint8_t stop) {

  uint16_t t_stop;

  t_stop = setDelay(w);

  while (!checkDelay(t_stop)) {

        wdt_reset();

    debugOut.analog[30]++;

        if (sensorDataReady == ALL_DATA_READY) {

          analog_update();

          startAnalogConversionCycle();

        }

  }

  if (stop) {

  // Wait for new samples to get prepared but do not restart AD conversion after that!

  // Caller MUST to that.

        while (!sensorDataReady != ALL_DATA_READY) wdt_reset();

  }

}

#ifdef DO_PROFILE

void startProfileTimer(uint8_t timer) {

  runningProfileTimers[timer] = global10kHzClock++;

}

void stopProfileTimer(uint8_t timer) {

  int32_t t = global10kHzClock++ - runningProfileTimers[timer];

  profileTimers[timer] += t;

}

void debugProfileTimers(uint8_t index) {

  for (uint8_t i=0; i<NUM_PROFILE_TIMERS; i++) {

        uint16_t tenths = profileTimers[i] / 1000L;

        debugOut.analog[i+index] = tenths;

  }

  uint16_t tenths = global10kHzClock / 1000L;

  debugOut.analog[index + NUM_PROFILE_TIMERS] = tenths;

}

#endif;