Subversion Repositories FlightCtrl

Rev

Rev 2135 | Details | Compare with Previous | Last modification | View Log | RSS feed

Rev Author Line No. Line
2108 - 1
#include <inttypes.h>
2
#include <avr/io.h>
3
#include <avr/interrupt.h>
2132 - 4
#include <avr/wdt.h>
2108 - 5
#include "eeprom.h"
6
#include "analog.h"
7
#include "controlMixer.h"
8
 
9
#include "timer0.h"
10
#include "output.h"
11
 
2132 - 12
#ifdef DO_PROFILE
13
volatile uint32_t global10kHzClock = 0;
14
volatile int32_t profileTimers[NUM_PROFILE_TIMERS];
15
volatile int32_t runningProfileTimers[NUM_PROFILE_TIMERS];
2108 - 16
#endif
17
 
18
volatile uint32_t globalMillisClock = 0;
19
volatile uint8_t  runFlightControl = 0;
20
volatile uint16_t beepTime = 0;
21
volatile uint16_t beepModulation = BEEP_MODULATION_NONE;
22
 
23
/*****************************************************
24
 * Initialize Timer 0                  
25
 *****************************************************/
26
// timer 0 is used for the PWM generation to control the offset voltage at the air pressure sensor
27
// Its overflow interrupt routine is used to generate the beep signal and the flight control motor update rate
28
void timer0_init(void) {
29
  uint8_t sreg = SREG;
30
 
31
  // disable all interrupts before reconfiguration
32
  cli();
33
 
2109 - 34
  // Configure speaker port as output and also the diags pin D2
35
  DDRD |= ((1 << DDD5) | (1 << DDD2));
36
  PORTD &= ~((1 << PORTD5) | (1 << DDD2));
2108 - 37
 
38
  // Timer/Counter 0 Control Register A
39
 
40
  // Waveform Generation Mode is Fast PWM (Bits WGM02 = 0, WGM01 = 1, WGM00 = 1)
41
  // Clear OC0A on Compare Match, set OC0A at BOTTOM, noninverting PWM (Bits COM0A1 = 1, COM0A0 = 0)
42
  // Clear OC0B on Compare Match, set OC0B at BOTTOM, (Bits COM0B1 = 1, COM0B0 = 0)
43
  // TCCR0A &= ~((1 << COM0A0) | (1 << COM0B0));
44
  // TCCR0A |= (1 << COM0A1) | (1 << COM0B1) | (1 << WGM01) | (1 << WGM00);
45
 
46
  // Timer/Counter 0 Control Register B
47
  // set clock divider for timer 0 to SYSCLOCK/8 = 20MHz/8 = 2.5MHz
48
  // i.e. the timer increments from 0x00 to 0xFF with an update rate of 2.5 MHz
49
  // hence the timer overflow interrupt frequency is 2.5 MHz/256 = 9.765 kHz
50
 
51
  // divider 8 (Bits CS02 = 0, CS01 = 1, CS00 = 0)
52
  TCCR0B &= ~((1 << FOC0A) | (1 << FOC0B) | (1 << WGM02));
53
  TCCR0B = (TCCR0B & 0xF8) | (0 << CS02) | (1 << CS01) | (0 << CS00);
54
 
55
  // initialize the Output Compare Register A & B used for PWM generation on port PB3 & PB4
56
  OCR0A = 0;    // for PB3
57
  OCR0B = 120;  // for PB4
58
 
59
  // init Timer/Counter 0 Register
60
  TCNT0 = 0;
61
 
62
  // Timer/Counter 0 Interrupt Mask Register
63
  // enable timer overflow interrupt only
64
  TIMSK0 &= ~((1 << OCIE0B) | (1 << OCIE0A));
65
  TIMSK0 |= (1 << TOIE0);
66
 
2132 - 67
#ifdef DO_PROFILE
68
  for (uint8_t i=0; i<NUM_PROFILE_TIMERS; i++) {
69
          profileTimers[i] = 0;
70
  }
71
#endif
72
 
2108 - 73
  SREG = sreg;
74
}
75
 
76
/*****************************************************/
77
/*          Interrupt Routine of Timer 0             */
78
/*****************************************************/
79
ISR(TIMER0_OVF_vect) { // 9765.625 Hz
80
  static uint8_t cnt_1ms = 1, cnt = 0;
81
  uint8_t beeperOn = 0;
82
 
2132 - 83
#ifdef DO_PROFILE
84
    global10kHzClock++;
2108 - 85
#endif
86
 
2141 - 87
  if (!cnt--) { // every 10th run
2108 - 88
    cnt = 9;
89
    cnt_1ms ^= 1;
90
    if (!cnt_1ms) {
2141 - 91
      runFlightControl = 1; // every 2nd run
2108 - 92
    }
93
    globalMillisClock++; // increment millisecond counter
94
  }
95
 
96
  // beeper on if duration is not over
97
  if (beepTime) {
98
    beepTime--; // decrement BeepTime
99
    if (beepTime & beepModulation)
100
      beeperOn = 1;
101
    else
102
      beeperOn = 0;
103
  } else { // beeper off if duration is over
104
    beeperOn = 0;
105
    beepModulation = BEEP_MODULATION_NONE;
106
  }
107
 
108
  if (beeperOn) {
109
    // set speaker port to high.
110
      PORTD |= (1 << PORTD5); // Speaker at PD5
111
  } else { // beeper is off
112
    // set speaker port to low
113
      PORTD &= ~(1 << PORTD5);// Speaker at PD5
114
  }
115
 
116
#ifdef USE_MK3MAG
117
  // update compass value if this option is enabled in the settings
118
  if (staticParams.bitConfig & CFG_COMPASS_ENABLED) {
119
    MK3MAG_periodicTask(); // read out mk3mag pwm
120
  }
121
#endif
122
}
123
 
124
// -----------------------------------------------------------------------
125
uint16_t setDelay(uint16_t t) {
126
  return (globalMillisClock + t - 1);
127
}
128
 
129
// -----------------------------------------------------------------------
130
int8_t checkDelay(uint16_t t) {
131
  return (((t - globalMillisClock) & 0x8000) >> 8); // check sign bit
132
}
133
 
134
// -----------------------------------------------------------------------
135
void delay_ms(uint16_t w) {
136
  uint16_t t_stop = setDelay(w);
137
  while (!checkDelay(t_stop))
2132 - 138
        wdt_reset();
2108 - 139
}
140
 
141
// -----------------------------------------------------------------------
142
void delay_ms_with_adc_measurement(uint16_t w, uint8_t stop) {
143
  uint16_t t_stop;
144
  t_stop = setDelay(w);
145
  while (!checkDelay(t_stop)) {
2132 - 146
        wdt_reset();
2108 - 147
        if (sensorDataReady == ALL_DATA_READY) {
148
          analog_update();
149
          startAnalogConversionCycle();
150
        }
151
  }
152
  if (stop) {
153
  // Wait for new samples to get prepared but do not restart AD conversion after that!
154
  // Caller MUST to that.
2135 - 155
        // while (sensorDataReady != ALL_DATA_READY) wdt_reset();
2108 - 156
  }
157
}
2132 - 158
 
159
#ifdef DO_PROFILE
160
void startProfileTimer(uint8_t timer) {
161
  runningProfileTimers[timer] = global10kHzClock++;
162
}
163
 
164
void stopProfileTimer(uint8_t timer) {
165
  int32_t t = global10kHzClock++ - runningProfileTimers[timer];
166
  profileTimers[timer] += t;
167
}
168
 
169
void debugProfileTimers(uint8_t index) {
170
  for (uint8_t i=0; i<NUM_PROFILE_TIMERS; i++) {
171
        uint16_t tenths = profileTimers[i] / 1000L;
172
        debugOut.analog[i+index] = tenths;
173
  }
174
  uint16_t tenths = global10kHzClock / 1000L;
175
  debugOut.analog[index + NUM_PROFILE_TIMERS] = tenths;
176
}
177
#endif;