Details | Last modification | View Log | RSS feed
| Rev | Author | Line No. | Line |
|---|---|---|---|
| 1910 | - | 1 | #include "analog.h" |
| 2 | #include "twimaster.h" |
||
| 3 | #include "configuration.h" |
||
| 4 | #include "timer0.h" |
||
| 5 | |||
| 6 | #define PITCHROLL_MINLIMIT GYRO_SUMMATION_FACTOR_PITCHROLL * 510 |
||
| 7 | #define PITCHROLL_MAXLIMIT GYRO_SUMMATION_FACTOR_PITCHROLL * 515 |
||
| 8 | |||
| 2025 | - | 9 | const uint8_t PR_GYROS_ORIENTATION_REVERSED = 0; |
| 1910 | - | 10 | const uint8_t GYRO_QUADRANT = 0; |
| 2025 | - | 11 | const uint8_t YAW_GYRO_REVERSED = 1; |
| 1910 | - | 12 | const uint8_t Z_ACC_REVERSED = 0; |
| 13 | |||
| 14 | // void gyro_init(void) {} |
||
| 15 | void gyro_calibrate(void) { |
||
| 16 | uint8_t i, axis, factor, numberOfAxesInRange = 0; |
||
| 17 | uint16_t timeout; |
||
| 18 | // GyroDefectNick = 0; GyroDefectRoll = 0; GyroDefectYaw = 0; |
||
| 19 | timeout = setDelay(2000); |
||
| 20 | |||
| 21 | for (i = 140; i != 0; i--) { |
||
| 22 | // If all 3 axis are in range, shorten the remaining number of iterations. |
||
| 23 | if (numberOfAxesInRange == 3 && i > 10) |
||
| 24 | i = 9; |
||
| 25 | numberOfAxesInRange = 0; |
||
| 26 | |||
| 27 | for (axis = PITCH; axis <= YAW; axis++) { |
||
| 28 | if (axis == YAW) |
||
| 29 | factor = GYRO_SUMMATION_FACTOR_YAW; |
||
| 30 | else |
||
| 31 | factor = GYRO_SUMMATION_FACTOR_PITCHROLL; |
||
| 32 | |||
| 33 | if (rawGyroSum[axis] < 510 * factor) |
||
| 34 | DACValues[axis]--; |
||
| 35 | else if (rawGyroSum[axis] > 515 * factor) |
||
| 36 | DACValues[axis]++; |
||
| 37 | else |
||
| 38 | numberOfAxesInRange++; |
||
| 39 | |||
| 40 | /* Gyro is defective. But do keep DAC within bounds (it's an op amp not a differential amp). */ |
||
| 41 | if (DACValues[axis] < 10) { |
||
| 42 | DACValues[axis] = 10; |
||
| 43 | } else if (DACValues[axis] > 245) { |
||
| 44 | DACValues[axis] = 245; |
||
| 45 | } |
||
| 46 | } |
||
| 47 | |||
| 48 | I2C_Start(TWI_STATE_GYRO_OFFSET_TX); // initiate data transmission |
||
| 49 | |||
| 50 | // Wait for I2C to finish transmission. |
||
| 51 | while (twi_state) { |
||
| 52 | // Did it take too long? |
||
| 53 | if (checkDelay(timeout)) { |
||
| 54 | // printf("\r\n DAC or I2C Error! check I2C, 3Vref, DAC, and BL-Ctrl"); |
||
| 55 | RED_ON; |
||
| 56 | break; |
||
| 57 | } |
||
| 58 | } |
||
| 59 | |||
| 60 | analog_start(); |
||
| 61 | |||
| 62 | delay_ms_Mess(i < 10 ? 10 : 2); |
||
| 63 | } |
||
| 64 | delay_ms_Mess(70); |
||
| 65 | } |
||
| 66 | |||
| 67 | void gyro_setDefaults(void) { |
||
| 2025 | - | 68 | staticParams.zerothOrderGyroCorrectionFactorx1000 = 25; |
| 69 | staticParams.secondOrderGyroCorrectionDivisor = 1; |
||
| 70 | staticParams.secondOrderGyroCorrectionLimit = 200; |
||
| 1910 | - | 71 | } |