Subversion Repositories FlightCtrl

#ifndef _MAIN_H

 #define _MAIN_H

#define QUADRO

//Hier die Quarz Frequenz einstellen

#if defined (__AVR_ATmega32__)

#define SYSCLK  20000000L       //Quarz Frequenz in Hz

#endif

#if defined (__AVR_ATmega644__)

#define SYSCLK  20000000L       //Quarz Frequenz in Hz

#endif

#if defined (__AVR_ATmega644P__)

#define SYSCLK  20000000L       //Quarz Frequenz in Hz

#endif

// neue Hardware

#define ROT_OFF   {if((PlatinenVersion == 10)||(PlatinenVersion == 20)) PORTB &=~0x01; else  PORTB |= 0x01;}

#define ROT_ON    {if((PlatinenVersion == 10)||(PlatinenVersion == 20)) PORTB |= 0x01; else  PORTB &=~0x01;}

#define ROT_FLASH PORTB ^= 0x01

#define GRN_OFF   {if((PlatinenVersion < 12)) PORTB &=~0x02; else PORTB |= 0x02;}

#define GRN_ON    {if((PlatinenVersion < 12)) PORTB |= 0x02; else PORTB &=~0x02;}

#define GRN_FLASH PORTB ^= 0x02

#define F_CPU SYSCLK

//#ifndef F_CPU

//#error ################## F_CPU nicht definiert oder ungültig #############

//#endif

//+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

#define EE_DATENREVISION 80 // wird angepasst, wenn sich die EEPROM-Daten geändert haben

#define MIXER_REVISION    1 // wird angepasst, wenn sich die Mixer-Daten geändert haben

#define EEPROM_ADR_VALID            1

#define EEPROM_ADR_ACTIVE_SET       2

#define EEPROM_ADR_LAST_OFFSET      3

#define EEPROM_ADR_ACC_NICK         4

#define EEPROM_ADR_ACC_ROLL         6

#define EEPROM_ADR_ACC_Z            8

#define EEPROM_ADR_MINUTES         10

#define EEPROM_ADR_MINUTES2        14

#define EEPROM_ADR_CHANNELS          80

#define EEPROM_ADR_PARAM_LENGTH      98

#define EEPROM_ADR_PARAM_BEGIN      100

#define EEPROM_ADR_MIXER_TABLE     1000 // 1001 - 1100

#define CFG_HOEHENREGELUNG       0x01

#define CFG_HOEHEN_SCHALTER      0x02

#define CFG_HEADING_HOLD         0x04

#define CFG_KOMPASS_AKTIV        0x08

#define CFG_KOMPASS_FIX          0x10

#define CFG_GPS_AKTIV            0x20

#define CFG_ACHSENKOPPLUNG_AKTIV 0x40

#define CFG_DREHRATEN_BEGRENZER  0x80

#define CFG_LOOP_OBEN            0x01

#define CFG_LOOP_UNTEN           0x02

#define CFG_LOOP_LINKS           0x04

#define CFG_LOOP_RECHTS          0x08

#define CFG_MOTOR_BLINK          0x10

#define CFG_MOTOR_OFF_LED1       0x20

#define CFG_MOTOR_OFF_LED2       0x40

#define CFG_RES4                         0x80

#define CFG2_HEIGHT_LIMIT        0x01

#define CFG2_VARIO_BEEP          0x02

#define CFG_SENSITIVE_RC         0x04

#define J3High    PORTD |= 0x20

#define J3Low     PORTD &= ~0x20

#define J4High    PORTD |= 0x10

#define J4Low     PORTD &= ~0x10

#define J5High    PORTD |= 0x08

#define J5Low     PORTD &= ~0x08

//#define  SYSCLK

//extern unsigned long SYSCLK;

extern volatile unsigned char SenderOkay;

extern unsigned char BattLowVoltageWarning;

extern unsigned char CosinusNickWinkel, CosinusRollWinkel;

extern unsigned char PlatinenVersion;

extern unsigned char SendVersionToNavi;

extern unsigned char servoValues[6];

void ReadParameterSet (unsigned char number, unsigned char *buffer, unsigned char length);

void WriteParameterSet(unsigned char number, unsigned char *buffer, unsigned char length);

extern unsigned char GetActiveParamSetNumber(void);

void SetActiveParamSetNumber(unsigned char number);

void LipoDetection(unsigned char print);

extern unsigned char EEPromArray[];

extern unsigned int FlugMinuten,FlugMinutenGesamt;

#include <stdlib.h>

#include <string.h>

#include <avr/io.h>

#include <avr/pgmspace.h>

#include <avr/interrupt.h>

#include <avr/eeprom.h>

#include <avr/boot.h>

#include <avr/wdt.h>

#include "old_macros.h"

#include "_Settings.h"

#include "printf_P.h"

#include "timer0.h"

#include "uart.h"

#include "analog.h"

#include "twimaster.h"

#include "menu.h"

#include "rc.h"

#include "fc.h"

#include "gps.h"

#include "spi.h"

#include "led.h"

#ifndef EEMEM

#define EEMEM __attribute__ ((section (".eeprom")))

#endif

#define DEBUG_DISPLAY_INTERVALL  123 // in ms

#define DELAY_US(x)     ((unsigned int)( (x) * 1e-6 * F_CPU ))

#endif //_MAIN_H