Subversion Repositories FlightCtrl

/*

    Copyright (c) 2008 Stefan Engelke <stefan@tinkerer.eu>

    Permission is hereby granted, free of charge, to any person

    obtaining a copy of this software and associated documentation

    files (the "Software"), to deal in the Software without

    restriction, including without limitation the rights to use, copy,

    modify, merge, publish, distribute, sublicense, and/or sell copies

    of the Software, and to permit persons to whom the Software is

    furnished to do so, subject to the following conditions:

    The above copyright notice and this permission notice shall be

    included in all copies or substantial portions of the Software.

    THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,

    EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF

    MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

    NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT

    HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,

    WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,

    OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER

    DEALINGS IN THE SOFTWARE.

    $Id: rcdsl.c 62 2008-08-21 16:09:07Z tensor $

    RCDSL.H and RCDSL.C is an INOFFICIAL implementation of the

    communication protocol used by DSL receivers of Act Europe.

    The DSL receivers have a serial communication port to connect

    two receivers in diversity mode. Each receiver is sending the

    received servo signals periodically over this port. This fact

    can be used to connect the receiver to the control unit of the

    model via UART instead of evaluating the PPM signal.

    The UART parameters are

    38400 Baud, 8-N-1

    If you have any questions, feel free to send me an e-mail.

Connection of DSL to SV1 of FC:

( DSL Pin1 is on side of channel 4 )

1. GND <--> pin 7 (GND)

2. TXD <--> pin 3 (RXD1 Atmega644p)

3. RXD <--> pin 4 (TXD1 Atmega644p) optional

4. 5V  <--> pin 2 (5V)

Do not connect the receiver via PPM-Sumsignal output the same time.

Data are send at 38400baud8n1

Data Frame: |0xFF|0xFF|0x1F|FREQALLOC|??|RSSI|VBAT|??|CRC|10|CH0D1|CH0D0|CH1D1|CH1D0|CRC| ...etc

FREQALLOC = 35, 40, 72

RSSI = 0.. 255 // Received signal strength indicator

VBAT = 0...255 // supply voltage (0.0V.. 8.2V)

Servo Pair:   |0x1X|CHXD1|CHXD0|CHX+1D1|CHX+1D0|CRC|

X is channel index of 1 servo value

D1D0 is servo value as u16 in range of 7373 (1ms) to 14745 (2ms)

there are 8 channels submitted, i.e 4 servo pairs

Frame examples with signel received

FFFF 1F23F079A304AD 1036012B1E6F 122AFB2AECB2 142B4D2B4404 1636872B33CE

FFFF 1F23F079A304AD 1036002B1F6F 122AFE2AEBB0 142B4B2B4406 1636872B33CE

FFFF 1F23F079A304AD 1035FF2B226E 122AFC2AEAB3 142B4E2B4304 1636882B33CD

FFFF 1F23F079A304AD 1036022B1E6E 122AFB2AEEB0 142B4A2B4506 1636872B33CE

FFFF 1F23F079A304AD 1036022B1E6E 122AFE2AEBB0 142B4B2B4406 1636882B33CD

FFFF 1F23F079A304AD 1036012B1E6F 122AFD2AEAB2 142B4E2B4403 1636862B33CF

FFFF 1F23F079A304AD 1036032B1D6E 122AFD2AEBB1 142B4C2B4504 1636862B33CF

Frame examples with no signal received

FFFF 1F23F000A30426

FFFF 1F23F000A30426

FFFF 1F23F000A30426

FFFF 1F23F000A30426

FFFF 1F23F000A30426

FFFF 1F23F000A30426

FFFF 1F23F000A30426

*/

#include "rcdsl.h"

#include "main.h"

volatile unsigned char data_counter   = 0;

volatile unsigned char last_byte      = 0;

unsigned char check_sum      = 0;

unsigned char paket_len      = 0;

#define UART1_BAUDRATE 38400

volatile uint8_t rcdsl_RSSI = 0;

volatile uint8_t rcdsl_battery=0;

volatile uint8_t rcdsl_allocation=0;

volatile uint8_t data[6];

typedef union {

        uint16_t pos[2];

        uint8_t dat[4];

} servos_t;

void rcdsl_init(void) {

    // Save state of status register and disable interrupts

    uint8_t sreg = SREG;

    cli();

    // Set baud rate

    UBRR1 = (uint16_t) ((uint32_t) F_CPU/(16*UART1_BAUDRATE) - 1);

    // UART Receiver und Transmitter anschalten 

    // Data mode 8N1, asynchron 

    UCSR1B = (1 << RXEN1) | (1 << TXEN0) | (1 << RXCIE1);

    UCSR1C = (1 << UCSZ11) | (1 << UCSZ10);

    // Flush Receive-Buffer

    do { UDR1; }

    while (UCSR1A & (1 << RXC1));

    // Clear rx and tx interrupt flags

    UCSR1A = (1 << RXC1) | (1 << TXC1);

    // Reactive interrupts, if they were active before

    SREG = sreg;

    printf("\n\rUART 1 initialized.");

}

void rcdsl_new_signal(uint8_t channel, int16_t signal)

// This function is called, when a new servo signal is properly received.

// Parameters: servo  - servo number (0-9)

//             signal - servo signal between 7373 (1ms) and 14745 (2ms)

{

    volatile signed int tmp;

    uint8_t index = channel+1; // Der MK fängt bei 1 an zu zählen

    // Signal vom  ACTDSL-Empfänger liegt zwischen

    // 7373 (1ms) und 14745 (2ms). 

    signal-= 11059;     // Neutralstellung zur Null verschieben

    signal/= 24;        // Auf MK Skalierung umrechnen

    // Stabiles Signal

    //if(abs(signal - PPM_in[index]) < 6) { if(SenderOkay < 200) SenderOkay += 10;}

    tmp = (3 * (PPM_in[index]) + signal) / 4;  

    if(tmp > signal+1) tmp--; else

    if(tmp < signal-1) tmp++;

    if(SenderOkay >= 105)  PPM_diff[index] = ((tmp - PPM_in[index]) / 3) * 3;

    else PPM_diff[index] = 0;

    PPM_in[index] = tmp;

    //NewPpmData = 0;

    //NewActData = 1;

    if(index == 4)  {

        //NewActData = 1;

        NewPpmData = 0;

        //PORTC = (PORTC&(~(1<<PC4))) | ((~PORTC)&(1<<PC4));

        //PINC = (1<<PC4);

    }

    //PPM_in[index] = signal;      

}

void rcdsl_incoming_paket(void)

// This function is called within rcdsl_parse_data(), when a complete 

// data paket with matching checksum has been received.

{

    uint8_t  i;

    static servos_t servos;

    // Look for status headers

    if ((data[0])==0x1F) {

        // Get frequency allocation

        rcdsl_allocation = data[0+1];

        // Get signal quality 

        rcdsl_RSSI = data[2+1];

        SenderOkay = (212 * (uint16_t) rcdsl_RSSI) / 128; // have to be scaled approx. by a factor of 1.66 to get 200 at full level

        if(SenderOkay > 255) SenderOkay = 255;

        // Get voltage of battery supply

        rcdsl_battery = data[3+1];

    }

    // Look for signal headers

    if ((data[0]&0xF0)==0x10) {

        i = data[0]&0x0F;   // Last 4 bits of the header indicates servo pair

        if (i<10) {

            // Convert byte array to two uint16

            servos.dat[1] = data[1];

            servos.dat[0] = data[2];

            servos.dat[3] = data[3];

            servos.dat[2] = data[4];

            rcdsl_new_signal(i  ,  (int16_t)servos.pos[0]);

            rcdsl_new_signal(i+1,  (int16_t)servos.pos[1]);

        }

    }

}

void rcdsl_parse_data(uint8_t b)

// This function should be called externaly, when a new data byte has 

// been received over uart.

{

    // Check for sync condition

    if ((b==0xFF) && (last_byte==0xFF)) {

        data_counter = 0;

        check_sum = 0;

        return;

    }

    // First byte is cmd

    if (data_counter == 0) {

        if (b==0x1F) paket_len = 5; else paket_len=4;

    }

    // Last byte is checksum

    if (data_counter > paket_len) {

        // Calculate checksum

        check_sum = ~check_sum;

        if (check_sum==0xFF) check_sum=0xFE;

        // If it match the received one, then apply data

        if (b==check_sum) rcdsl_incoming_paket();

        // Prepare for a new data paket

        data_counter = 0;

        check_sum = 0;

    // New byte within a paket

    } else {

        data[data_counter]  = b;

        check_sum          += b;

        data_counter++;

    }

    // Remember last byte received for detection of sync condition

    last_byte = b;

}

ISR (USART1_RX_vect)

{

    rcdsl_parse_data(UDR1);

}