Go to most recent revision | Details | Last modification | View Log | RSS feed
Rev | Author | Line No. | Line |
---|---|---|---|
755 | killagreg | 1 | #include <avr/io.h> |
782 | killagreg | 2 | #include <stdlib.h> |
765 | killagreg | 3 | #include "fc.h" |
4 | #include "timer0.h" |
||
782 | killagreg | 5 | #include "uart.h" |
755 | killagreg | 6 | |
7 | int32_t PWMHeading = -1; |
||
8 | uint8_t PWMTimeout = 0; |
||
9 | |||
10 | /*********************************************/ |
||
11 | /* Initialize Interface to CMPS02 Compass */ |
||
12 | /*********************************************/ |
||
13 | void CMPS03_Init(void) |
||
14 | { |
||
764 | killagreg | 15 | // Port PC4 connected to PWM output from compass module |
755 | killagreg | 16 | DDRC &= ~(1<<DDC4); // set as input |
764 | killagreg | 17 | PORTC |= (1<<PORTC4); // pull up to increase PWM counter also if nothing is connected |
755 | killagreg | 18 | |
19 | PWMTimeout = 0; |
||
20 | } |
||
21 | |||
22 | |||
23 | /*********************************************/ |
||
24 | /* Get Data from CMPS03 */ |
||
25 | /*********************************************/ |
||
26 | void CMPS03_Update(void) // called every 102.4 us by timer 0 ISR |
||
27 | { |
||
28 | static uint16_t PWMCount = 0; |
||
29 | // The pulse width varies from 1ms (0°) to 36.99ms (359.9°) |
||
30 | // in other words 100us/° with a +1ms offset. |
||
31 | // The signal goes low for 65ms between pulses, |
||
32 | // so the cycle time is 65mS + the pulse width. |
||
33 | // The pulse is generated by a 16 bit timer in the processor |
||
34 | // giving a 1uS resolution, however I would not recommend |
||
35 | // measuring this to anything better than 0.1° (10uS). |
||
36 | |||
37 | if(PINC & (1<<PINC4)) |
||
38 | { // If PWM signal is high increment PWM high counter |
||
39 | // This counter is incremented by a periode of 102.4us, |
||
40 | // i.e. the resoluton of pwm coded heading is approx. 1 deg. |
||
41 | PWMCount++; |
||
782 | killagreg | 42 | // pwm overflow? |
43 | if (PWMCount > 400) |
||
44 | { |
||
45 | if(PWMTimeout ) PWMTimeout--; // decrement timeout |
||
46 | PWMCount = 0; // reset PWM Counter |
||
47 | } |
||
48 | |||
755 | killagreg | 49 | } |
50 | else // PWM is low |
||
51 | { |
||
52 | if((PWMCount) && (PWMCount < 400)) |
||
53 | { |
||
785 | killagreg | 54 | if(PWMCount <9) PWMHeading = 0; |
55 | else PWMHeading = ((uint32_t)(PWMCount - 9) * 1049L) >> 10; // correct timebase and offset |
||
755 | killagreg | 56 | PWMTimeout = 12; // if 12 periodes long no valid PWM was detected the data are invalid |
57 | // 12 * 400 counts * 102.4 us = 419 ms |
||
58 | } |
||
59 | PWMCount = 0; // reset pwm counter |
||
60 | } |
||
61 | } |
||
62 | |||
63 | |||
64 | /*********************************************/ |
||
65 | /* Calculate north direction (heading) */ |
||
66 | /*********************************************/ |
||
67 | int16_t CMPS03_Heading(void) |
||
68 | { |
||
765 | killagreg | 69 | int16_t heading, w, v; |
782 | killagreg | 70 | |
71 | DebugOut.Analog[11] = PWMTimeout; |
||
72 | |||
755 | killagreg | 73 | if(PWMTimeout) |
765 | killagreg | 74 | { |
75 | w = abs(IntegralPitch / 512); |
||
76 | v = abs(IntegralRoll / 512); |
||
77 | if(v > w) w = v; // get maximum declination |
||
783 | killagreg | 78 | // if declination is small enough to have valid compass heading |
765 | killagreg | 79 | if(w < 35) |
80 | { |
||
81 | // range from 0 to 359 |
||
82 | heading = (int16_t)PWMHeading; |
||
83 | if (heading < 0) heading += 360; |
||
84 | heading = heading%360; |
||
85 | } |
||
782 | killagreg | 86 | else // compass to much tilted |
765 | killagreg | 87 | { |
88 | heading = -1; |
||
89 | } |
||
755 | killagreg | 90 | } |
91 | else // no data from compass |
||
92 | { |
||
782 | killagreg | 93 | if(!BeepTime) BeepTime = 100; // make noise to signal the compass problem |
755 | killagreg | 94 | heading = -1; |
95 | } |
||
96 | return heading; |
||
97 | } |