Subversion Repositories FlightCtrl

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

// + Copyright (c) 04.2007 Holger Buss

// + Nur für den privaten Gebrauch

// + www.MikroKopter.com

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

// + Es gilt für das gesamte Projekt (Hardware, Software, Binärfiles, Sourcecode und Dokumentation),

// + dass eine Nutzung (auch auszugsweise) nur für den privaten (nicht-kommerziellen) Gebrauch zulässig ist.

// + Sollten direkte oder indirekte kommerzielle Absichten verfolgt werden, ist mit uns (info@mikrokopter.de) Kontakt

// + bzgl. der Nutzungsbedingungen aufzunehmen.

// + Eine kommerzielle Nutzung ist z.B.Verkauf von MikroKoptern, Bestückung und Verkauf von Platinen oder Bausätzen,

// + Verkauf von Luftbildaufnahmen, usw.

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

// + Werden Teile des Quellcodes (mit oder ohne Modifikation) weiterverwendet oder veröffentlicht,

// + unterliegen sie auch diesen Nutzungsbedingungen und diese Nutzungsbedingungen incl. Copyright müssen dann beiliegen

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

// + Sollte die Software (auch auszugesweise) oder sonstige Informationen des MikroKopter-Projekts

// + auf anderen Webseiten oder sonstigen Medien veröffentlicht werden, muss unsere Webseite "http://www.mikrokopter.de"

// + eindeutig als Ursprung verlinkt werden

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

// + Keine Gewähr auf Fehlerfreiheit, Vollständigkeit oder Funktion

// + Benutzung auf eigene Gefahr

// + Wir übernehmen keinerlei Haftung für direkte oder indirekte Personen- oder Sachschäden

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

// + Die Portierung der Software (oder Teile davon) auf andere Systeme (ausser der Hardware von www.mikrokopter.de) ist nur

// + mit unserer Zustimmung zulässig

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

// + Die Funktion printf_P() unterliegt ihrer eigenen Lizenz und ist hiervon nicht betroffen

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

// + Redistributions of source code (with or without modifications) must retain the above copyright notice,

// + this list of conditions and the following disclaimer.

// +   * Neither the name of the copyright holders nor the names of contributors may be used to endorse or promote products derived

// +     from this software without specific prior written permission.

// +   * The use of this project (hardware, software, binary files, sources and documentation) is only permittet

// +     for non-commercial use (directly or indirectly)

// +     Commercial use (for excample: selling of MikroKopters, selling of PCBs, assembly, ...) is only permitted

// +     with our written permission

// +   * If sources or documentations are redistributet on other webpages, out webpage (http://www.MikroKopter.de) must be

// +     clearly linked as origin

// +   * porting to systems other than hardware from www.mikrokopter.de is not allowed

// +  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

// +  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

// +  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

// +  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE

// +  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

// +  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

// +  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

// +  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN// +  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

// +  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE

// +  POSSIBILITY OF SUCH DAMAGE.

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

#include <inttypes.h>

#include <avr/io.h>

#include <avr/interrupt.h>

#include "eeprom.h"

#include "analog.h"

#include "main.h"

#include "fc.h"

#ifdef USE_KILLAGREG

#include "mm3.h"

#endif

#ifdef USE_MK3MAG

#include "mk3mag.h"

#endif

volatile uint8_t Count100uSeconds=0;

volatile uint16_t CountMilliseconds = 0;

volatile uint8_t UpdateMotor = 0;

volatile uint16_t cntKompass = 0;

volatile uint16_t BeepTime = 0;

volatile uint16_t BeepModulation = 0xFFFF;

#ifdef USE_NAVICTRL

volatile uint8_t SendSPI = 0;

#endif

/*****************************************************/

/*              Initialize Timer 0                   */

/*****************************************************/

// timer 0 is used for the PWM generation to control the offset voltage at the air pressure sensor

// Its overflow interrupt routine is used to generate the beep signal and the flight control motor update rate

void TIMER0_Init(void)

{

        uint8_t sreg = SREG;

        // disable all interrupts before reconfiguration

        cli();

        // configure speaker port as output

        if(BoardRelease == 10)

        {       // Speaker at PD2

                DDRD |= (1<<DDD2);

                PORTD &= ~(1<<PORTD2);

        }

        else

        {       // Speaker at PC7

                DDRC |= (1<<DDC7);

                PORTC &= ~(1<<PORTC7);

        }

        // set PB3 and PB4 as output for the PWM used as offset for the pressure sensor

        DDRB |= (1<<DDB4)|(1<<DDB3);

        PORTB &= ~((1<<PORTB4)|(1<<PORTB3));

        // Timer/Counter 0 Control Register A

        // Waveform Generation Mode is Fast PWM (Bits WGM02 = 0, WGM01 = 1, WGM00 = 1)

        // Clear OC0A on Compare Match, set OC0A at BOTTOM, noninverting PWM (Bits COM0A1 = 1, COM0A0 = 0)

        // Clear OC0B on Compare Match, set OC0B at BOTTOM, (Bits COM0B1 = 1, COM0B0 = 0)

        TCCR0A &= ~((1<<COM0A0)|(1<<COM0B0));

        TCCR0A |= (1<<COM0A1)|(1<<COM0B1)|(1<<WGM01)|(1<<WGM00);

        // Timer/Counter 0 Control Register B

        // set clock divider for timer 0 to SYSKLOCK/8 = 20MHz / 8 = 2.5MHz

        // i.e. the timer increments from 0x00 to 0xFF with an update rate of 2.5 MHz

        // hence the timer overflow interrupt frequency is 2.5 MHz / 256 = 9.765 kHz

        // divider 8 (Bits CS02 = 0, CS01 = 1, CS00 = 0)

        TCCR0B &= ~((1<<FOC0A)|(1<<FOC0B)|(1<<WGM02));

        TCCR0B = (TCCR0B & 0xF8)|(0<<CS02)|(1<<CS01)|(0<<CS00);

        // initialize the Output Compare Register A & B used for PWM generation on port PB3 & PB4

        OCR0A =  0;  // for PB3

        OCR0B = 120; // for PB4

        // init Timer/Counter 0 Register

        TCNT0 = 0;

        // Timer/Counter 0 Interrupt Mask Register

        // enable timer overflow interrupt only

        TIMSK0 &= ~((1<<OCIE0B)|(1<<OCIE0A));

        TIMSK0 |= (1<<TOIE0);

        SREG = sreg;

}

/*****************************************************/

/*          Interrupt Routine of Timer 0             */

/*****************************************************/

ISR(TIMER0_OVF_vect)    // 9.765 kHz

{

        static uint8_t cnt_1ms = 1,cnt = 0;

        uint8_t Beeper_On = 0;

        Count100uSeconds++;

#ifdef USE_NAVICTRL

        if(SendSPI) SendSPI--; // if SendSPI is 0, the transmit of a byte via SPI bus to and from The Navicontrol is done

#endif

        if(!cnt--) // every 10th run (9.765kHz/10 = 976Hz)

        {

                cnt = 9;

                cnt_1ms++;

                cnt_1ms %= 2;

                if(!cnt_1ms) UpdateMotor = 1; // every 2nd run (976Hz/2 = 488 Hz)

                CountMilliseconds++; // increment millisecond counter

        }

        // beeper on if duration is not over

        if(BeepTime)

        {

                BeepTime--; // decrement BeepTime

                if(BeepTime & BeepModulation) Beeper_On = 1;

                else Beeper_On = 0;

        }

        else // beeper off if duration is over

        {

                Beeper_On = 0;

                BeepModulation = 0xFFFF;

        }

        // if beeper is on

        if(Beeper_On)

        {

                // set speaker port to high

                if(BoardRelease == 10) PORTD |= (1<<PORTD2); // Speaker at PD2

                else                   PORTC |= (1<<PORTC7); // Speaker at PC7

        }

        else // beeper is off

        {

                // set speaker port to low

                if(BoardRelease == 10) PORTD &= ~(1<<PORTD2);// Speaker at PD2

                else                   PORTC &= ~(1<<PORTC7);// Speaker at PC7

        }

        #ifndef USE_NAVICTRL

        // update compass value if this option is enabled in the settings

        if(ParamSet.GlobalConfig & (CFG_COMPASS_ACTIVE|CFG_GPS_ACTIVE))

        {

        #ifdef USE_KILLAGREG

                MM3_Update(); // read out mm3 board

        #endif

        #ifdef USE_MK3MAG

                MK3MAG_Update(); // read out mk3mag pwm

        #endif

        }

        #endif

}

// -----------------------------------------------------------------------

uint16_t SetDelay (uint16_t t)

{

        return(CountMilliseconds + t - 1);

}

// -----------------------------------------------------------------------

int8_t CheckDelay(uint16_t t)

{

        return(((t - CountMilliseconds) & 0x8000) >> 8); // check sign bit

}

// -----------------------------------------------------------------------

void Delay_ms(uint16_t w)

{

        uint16_t t_stop;

        t_stop = SetDelay(w);

        while (!CheckDelay(t_stop));

}

// -----------------------------------------------------------------------

void Delay_ms_Mess(uint16_t w)

{

        uint16_t t_stop;

        t_stop = SetDelay(w);

        while (!CheckDelay(t_stop))

        {

                if(ADReady)

                {

                        ADReady = 0;

                        ADC_Enable();

                }

        }

}