Go to most recent revision | Details | Last modification | View Log | RSS feed
| Rev | Author | Line No. | Line |
|---|---|---|---|
| 508 | walter | 1 | ******************************************************************************** |
| 2 | in "makefile": |
||
| 3 | MCU = atmega644 |
||
| 4 | ändern in: |
||
| 5 | MCU = atmega644p |
||
| 6 | |||
| 7 | in "makefile" an entsprechender Stelle hinzufügen: |
||
| 8 | ifeq ($(MCU), atmega644p) |
||
| 9 | FUSE_SETTINGS = -u -U lfuse:w:0xff:m -U hfuse:w:0xdf:m |
||
| 10 | #FUSE_SETTINGS = -U lfuse:w:0xff:m -U hfuse:w:0xdf:m |
||
| 11 | |||
| 12 | # -u bei neuen Controllern wieder einspielen |
||
| 13 | |||
| 14 | HEX_NAME = MEGA644P |
||
| 15 | endif |
||
| 16 | |||
| 17 | |||
| 18 | ******************************************************************************** |
||
| 19 | in "main.h" hinzufügen: (bei den anderen #defines) |
||
| 20 | |||
| 21 | #if defined (__AVR_ATmega644P__) |
||
| 22 | #define SYSCLK 20000000L //Quarz Frequenz in Hz |
||
| 23 | //#define SYSCLK 16000000L //Quarz Frequenz in Hz |
||
| 24 | #endif |
||
| 25 | |||
| 26 | ******************************************************************************** |
||
| 27 | in "rc.h" hinzufügen: (bei den anderen #defines) |
||
| 28 | #if defined (__AVR_ATmega644P__) |
||
| 29 | //#define TIMER_TEILER CK64 |
||
| 30 | #define TIMER_RELOAD_VALUE 250 |
||
| 31 | //#define TIMER_TEILER CK256 // bei 20MHz |
||
| 32 | //#define TIMER_RELOAD_VALUE -78 // bei 20MHz |
||
| 33 | #endif |
||
| 34 | |||
| 35 | ******************************************************************************** |
||
| 36 | in "uart.h" hinzufügen: (bei den anderen #defines) |
||
| 37 | #if defined (__AVR_ATmega644P__) |
||
| 38 | # define USR UCSR0A |
||
| 39 | # define UCR UCSR0B |
||
| 40 | # define UDR UDR0 |
||
| 41 | # define UBRR UBRR0L |
||
| 42 | # define EICR EICR0B |
||
| 43 | # define TXEN TXEN0 |
||
| 44 | # define RXEN RXEN0 |
||
| 45 | # define RXCIE RXCIE0 |
||
| 46 | # define TXCIE TXCIE0 |
||
| 47 | # define U2X U2X0 |
||
| 48 | # define UCSRB UCSR0B |
||
| 49 | # define UDRE UDRE0 |
||
| 50 | # define INT_VEC_RX SIG_USART_RECV |
||
| 51 | # define INT_VEC_TX SIG_USART_TRANS |
||
| 52 | #endif |
||
| 53 | |||
| 54 | #define BAUD_RATE1 57600 //Baud Rate für UART2 |
||
| 55 | |||
| 56 | ******************************************************************************** |
||
| 57 | in "uart.c" hinzufügen: und die entsprechenden interrupt routinen mit code füllen |
||
| 58 | |||
| 59 | |||
| 60 | //############################################################################ |
||
| 61 | //INstallation der 2ten Seriellen Schnittstelle |
||
| 62 | void UART1_Init (void) |
||
| 63 | //############################################################################ |
||
| 64 | { |
||
| 65 | //Enable TXEN im Register UCR TX-Data Enable & RX Enable |
||
| 66 | |||
| 67 | UCSR1B=(1 << TXEN) | (1 << RXEN); |
||
| 68 | // UART Double Speed (U2X) |
||
| 69 | UCSR1A |= (1<<U2X); |
||
| 70 | // RX-Interrupt Freigabe |
||
| 71 | UCSR1B |= (1<<RXCIE); |
||
| 72 | // TX-Interrupt Freigabe |
||
| 73 | UCSR1B |= (1<<TXCIE); |
||
| 74 | |||
| 75 | //Teiler wird gesetzt |
||
| 76 | UBRR1L=(SYSCLK / (BAUD_RATE1 * 8L) - 1); |
||
| 77 | //UBRR1L = 33; |
||
| 78 | //öffnet einen Kanal für printf (STDOUT) |
||
| 79 | //fdevopen (uart_putchar, 0); |
||
| 80 | //sbi(PORTD,4); |
||
| 81 | Debug_Timer = SetDelay(200); |
||
| 82 | } |
||
| 83 | |||
| 84 | |||
| 85 | |||
| 86 | //+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
||
| 87 | //++ Sende-Part der Datenübertragung an zweiten UART |
||
| 88 | //+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
||
| 89 | SIGNAL(SIG_USART1_RECV) |
||
| 90 | { |
||
| 91 | |||
| 92 | |||
| 93 | |||
| 94 | } |
||
| 95 | |||
| 96 | |||
| 97 | //+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
||
| 98 | //++ Empfangs-Part der Datenübertragung von zweitem UART |
||
| 99 | //+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ |
||
| 100 | SIGNAL(SIG_USART1_TRANS) |
||
| 101 | { |
||
| 102 | |||
| 103 | |||
| 104 | |||
| 105 | } |
||
| 106 | |||
| 107 | |||
| 108 | |||
| 109 | ******************************************************************************** |
||
| 110 | in "main.c" an geeigneter Stelle (z.B. dort wo bereits "UART_Init" aufgerufen wird nun auch "UART1_Init" aufrufen |
||
| 111 | |||
| 112 | |||
| 113 | |||
| 114 | |||
| 115 | |||
| 116 | |||
| 117 |