Details | Last modification | View Log | RSS feed
| Rev | Author | Line No. | Line |
|---|---|---|---|
| 1515 | - | 1 | #ifndef _I2C_MASTER_H |
| 2 | #define _I2C_MASTER_H |
||
| 3 | |||
| 4 | |||
| 5 | #include <inttypes.h> |
||
| 6 | |||
| 7 | #define TWI_STATE_MOTOR_TX 0 |
||
| 8 | #define TWI_STATE_MOTOR_RX 5 |
||
| 9 | #define TWI_STATE_GYRO_OFFSET_TX 18 |
||
| 10 | |||
| 11 | extern volatile uint8_t twi_state; |
||
| 12 | extern volatile uint8_t motor_write; |
||
| 13 | extern volatile uint8_t motor_read; |
||
| 14 | extern volatile uint8_t I2C_TransferActive; |
||
| 15 | |||
| 16 | extern uint8_t MissingMotor; |
||
| 17 | |||
| 18 | #define MAX_MOTORS 12 |
||
| 19 | #define MOTOR_STATE_PRESENT_MASK 0x80 |
||
| 20 | #define MOTOR_STATE_ERROR_MASK 0x7F |
||
| 21 | #define MOTOR_STATE_NEW_PROTOCOL_MASK 0x01 |
||
| 22 | #define BLFLAG_TX_COMPLETE 0x01 |
||
| 23 | #define BLFLAG_READ_VERSION 0x02 |
||
| 24 | |||
| 25 | extern volatile uint8_t BLFlags; |
||
| 26 | extern char MotorenEin; |
||
| 27 | unsigned char MotorTest[16]; |
||
| 28 | #define BL_READMODE_STATUS 0 |
||
| 29 | #define BL_READMODE_CONFIG 16 |
||
| 30 | |||
| 31 | typedef struct |
||
| 32 | { |
||
| 33 | uint8_t Version; // the version of the BL (0 = old) |
||
| 34 | uint8_t SetPoint; // written by attitude controller |
||
| 35 | uint8_t SetPointLowerBits; // for higher Resolution of new BLs |
||
| 36 | uint8_t State; // 7 bit for I2C error counter, highest bit indicates if motor is present |
||
| 37 | uint8_t ReadMode; // select data to read |
||
| 38 | // the following bytes must be exactly in that order! |
||
| 39 | uint8_t Current; // in 0.1 A steps, read back from BL |
||
| 40 | uint8_t MaxPWM; // read back from BL is less than 255 if BL is in current limit |
||
| 41 | int8_t Temperature; // old BL-Ctrl will return a 255 here, the new version the temp. in �C |
||
| 42 | } __attribute__((packed)) MotorData_t; |
||
| 43 | |||
| 44 | extern MotorData_t Motor[MAX_MOTORS]; |
||
| 45 | |||
| 46 | #define BLCONFIG_REVISION 2 |
||
| 47 | |||
| 48 | #define MASK_SET_PWM_SCALING 0x01 |
||
| 49 | #define MASK_SET_CURRENT_LIMIT 0x02 |
||
| 50 | #define MASK_SET_TEMP_LIMIT 0x04 |
||
| 51 | #define MASK_SET_CURRENT_SCALING 0x08 |
||
| 52 | #define MASK_SET_BITCONFIG 0x10 |
||
| 53 | #define MASK_RESET_CAPCOUNTER 0x20 |
||
| 54 | #define MASK_SET_DEFAULT_PARAMS 0x40 |
||
| 55 | #define MASK_SET_SAVE_EEPROM 0x80 |
||
| 56 | |||
| 57 | #define BITCONF_REVERSE_ROTATION 0x01 |
||
| 58 | #define BITCONF_RES1 0x02 |
||
| 59 | #define BITCONF_RES2 0x04 |
||
| 60 | #define BITCONF_RES3 0x08 |
||
| 61 | #define BITCONF_RES4 0x10 |
||
| 62 | #define BITCONF_RES5 0x20 |
||
| 63 | #define BITCONF_RES6 0x40 |
||
| 64 | #define BITCONF_RES7 0x80 |
||
| 65 | |||
| 66 | typedef struct |
||
| 67 | { |
||
| 68 | uint8_t Revision; // must be BL_REVISION |
||
| 69 | uint8_t SetMask; // settings mask |
||
| 70 | uint8_t PwmScaling; // maximum value of control pwm, acts like a thrust limit |
||
| 71 | uint8_t CurrentLimit; // current limit in A |
||
| 72 | uint8_t TempLimit; // in �C |
||
| 73 | uint8_t CurrentScaling; // scaling factor for current measurement |
||
| 74 | uint8_t BitConfig; // see defines above |
||
| 75 | uint8_t crc; // checksum |
||
| 76 | } __attribute__((packed)) BLConfig_t; |
||
| 77 | |||
| 78 | extern BLConfig_t BLConfig; |
||
| 79 | |||
| 80 | extern volatile uint16_t I2CTimeout; |
||
| 81 | |||
| 82 | void I2C_Init(char); // Initialize I2C |
||
| 83 | #define I2C_Start(start_state) {twi_state = start_state; BLFlags &= ~BLFLAG_TX_COMPLETE; TWCR = (1<<TWSTA) | (1<<TWEN) | (1<<TWINT) | (1<<TWIE);} |
||
| 84 | #define I2C_Stop(start_state) {twi_state = start_state; TWCR = (1<<TWEN) | (1<<TWSTO) | (1<<TWINT);} |
||
| 85 | void I2C_Reset(void); // Reset I2C |
||
| 86 | |||
| 87 | #define BLCONFIG_SUCCESS 0 |
||
| 88 | #define BLCONFIG_ERR_MOTOR_RUNNING 1 |
||
| 89 | #define BLCONFIG_ERR_MOTOR_NOT_EXIST 2 |
||
| 90 | #define BLCONFIG_ERR_HW_NOT_COMPATIBLE 3 |
||
| 91 | #define BLCONFIG_ERR_SW_NOT_COMPATIBLE 4 |
||
| 92 | #define BLCONFIG_ERR_CHECKSUM 5 |
||
| 93 | #define BLCONFIG_ERR_READ_NOT_POSSIBLE 6 |
||
| 94 | |||
| 95 | uint8_t I2C_WriteBLConfig(uint8_t motor); |
||
| 96 | uint8_t I2C_ReadBLConfig(uint8_t motor); |
||
| 97 | |||
| 98 | #endif |
||
| 99 | |||
| 100 |