WebSVN - FlightCtrl - Log - Rev 2548

3295 d 0 h

holgerb

2.10a (10.11.2014 - 17.04.2015)
- New data structure of ExternalControl
- Internal Copies of the Channel values
- NC-Yawing rate limited to 100°/sec
- ExpandBaro faster -> 80ms instead of 700ms
- Altitude measurement re-calibrated (the measured value was about 5% too high)
- transmit receiver type to NC
- transmit stored neutral values (BOAT) to NC
- SPI communication optimized -> some Data are faster, some are slower
- BL-State (Current, Temperature,...) are now faster transferred for Logging
- ComingHome: automatic Direction change
- allows Yawing without CareFree (Yawing at Coming Home)
- Bugfix: Output LED Blinking when RC-Lost
- bugfix: uBat in 16Bit
- AnalogLable CRC implemented -> KopterTool doesn't need to read them every time
- ShutterCounter -> counts up when the output switches from low to high
- transmit LipoCount to NC
- Config "Disable CameraCompensation" disables also Roll-Compensation now
- AccZ in 3D-Datastructure (for Ben)
- new Parameter: LandingAccZ
- 16 Motors
- in-flight HoTT: Motortest and ACC-Calibration
- Error Message: No Redundancy
- Error Message: Redundancy Test
- Redundant Slave: copy the Current, State and Temperature from the UART Data
- in-flight ACC-Calibration with Jeti and KopterTool
- ACC-Calibration by stick: 5 seconds delay
- Bugfix: LED pattern was not used more often if the Hold time was longer than the pattern time
- Servo Failsafe Positions implemented
-> That Position is used for RC-Lost and UnderVoltage-Autolanding
-> minimum 10 seconds active
- MULTIPLEX servo protocol implemented (12 & 16 Channels)

1523

From rev	To rev	Max revs

Search history for

Show All

Subversion Repositories FlightCtrl

(root)/tags/V2.10a/mymath.c @ 2739 - Rev 2548

Filtering Options

Rev	Age	Author	Path	Log message
2548	3295 d 0 h	holgerb	/tags/V2.10a/	2.10a (10.11.2014 - 17.04.2015) - New data structure of ExternalControl - Internal Copies of the Channel values - NC-Yawing rate limited to 100°/sec - ExpandBaro faster -> 80ms instead of 700ms - Altitude measurement re-calibrated (the measured value was about 5% too high) - transmit receiver type to NC - transmit stored neutral values (BOAT) to NC - SPI communication optimized -> some Data are faster, some are slower - BL-State (Current, Temperature,...) are now faster transferred for Logging - ComingHome: automatic Direction change - allows Yawing without CareFree (Yawing at Coming Home) - Bugfix: Output LED Blinking when RC-Lost - bugfix: uBat in 16Bit - AnalogLable CRC implemented -> KopterTool doesn't need to read them every time - ShutterCounter -> counts up when the output switches from low to high - transmit LipoCount to NC - Config "Disable CameraCompensation" disables also Roll-Compensation now - AccZ in 3D-Datastructure (for Ben) - new Parameter: LandingAccZ - 16 Motors - in-flight HoTT: Motortest and ACC-Calibration - Error Message: No Redundancy - Error Message: Redundancy Test - Redundant Slave: copy the Current, State and Temperature from the UART Data - in-flight ACC-Calibration with Jeti and KopterTool - ACC-Calibration by stick: 5 seconds delay - Bugfix: LED pattern was not used more often if the Hold time was longer than the pattern time - Servo Failsafe Positions implemented -> That Position is used for RC-Lost and UnderVoltage-Autolanding -> minimum 10 seconds active - MULTIPLEX servo protocol implemented (12 & 16 Channels)
2486			/trunk/mymath.c
1523			/trunk/mymath.c
1490			/trunk/mymath.c
1344			/trunk/mymath.c
1328			/trunk/mymath.c
1320			/trunk/mymath.c