Subversion Repositories FlightCtrl

Rev

Rev 935 | Rev 942 | Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | RSS feed

// ######################## SPI - FlightCtrl ###################
#include <avr/io.h>
#include <avr/interrupt.h>
#include <string.h>
#include <stdlib.h>
#include "_Settings.h"
#include "spi.h"
#include "fc.h"
#include "rc.h"
#include "eeprom.h"
#include "uart.h"
#include "timer0.h"
#include "analog.h"

#define SPI_TXSYNCBYTE1 0xAA
#define SPI_TXSYNCBYTE2 0x83
#define SPI_RXSYNCBYTE1 0x81
#define SPI_RXSYNCBYTE2 0x55

typedef enum
{
        SPI_SYNC1,
        SPI_SYNC2,
        SPI_DATA
} SPI_RXState_t;


// data exchange packets to and From NaviCtrl
ToNaviCtrl_t    ToNaviCtrl;
FromNaviCtrl_t  FromNaviCtrl;

// rx packet buffer
#define SPI_RXBUFFER_LEN sizeof(FromNaviCtrl)
uint8_t SPI_RxBuffer[SPI_RXBUFFER_LEN];
uint8_t SPI_RxBufferIndex = 0;
uint8_t SPI_RxBuffer_Request = 0;

// tx packet buffer
#define SPI_TXBUFFER_LEN sizeof(ToNaviCtrl)
uint8_t *SPI_TxBuffer;
uint8_t SPI_TxBufferIndex = 0;

uint8_t SPITransferCompleted, SPI_ChkSum;
uint8_t SPI_RxDataValid;

uint8_t SPI_CommandSequence[] = { SPI_CMD_USER, SPI_CMD_STICK, SPI_CMD_PARAMETER1, SPI_CMD_STICK, SPI_CMD_CAL_COMPASS };
uint8_t SPI_CommandCounter = 0;

/*********************************************/
/*  Initialize SPI interface to NaviCtrl     */
/*********************************************/
void SPI_MasterInit(void)
{
        DDR_SPI |= (1<<DD_MOSI)|(1<<DD_SCK);    // Set MOSI and SCK output, all others input
        SLAVE_SELECT_DDR_PORT |= (1 << SPI_SLAVE_SELECT); // set Slave select port as output port

        SPCR = (1<<SPE)|(1<<MSTR)|(1<<SPR1)|(0<<SPR0)|(0<<SPIE);   // Enable SPI, Master, set clock rate fck/64
        SPSR = 0;//(1<<SPI2X);

        SLAVE_SELECT_PORT |=  (1 << SPI_SLAVE_SELECT); // Deselect Slave

        SPI_TxBuffer = (uint8_t *) &ToNaviCtrl; // set pointer to tx-buffer
        SPITransferCompleted = 1;
        // initialize data packet to NaviControl
        ToNaviCtrl.Sync1 = SPI_TXSYNCBYTE1;
        ToNaviCtrl.Sync2 = SPI_TXSYNCBYTE2;

        ToNaviCtrl.Command = SPI_CMD_USER;
        ToNaviCtrl.IntegralNick = 0;
        ToNaviCtrl.IntegralRoll = 0;
        SPI_RxDataValid = 0;
}


/**********************************************************/
/*  Update Data transferd by the SPI from/to NaviCtrl     */
/**********************************************************/
void UpdateSPI_Buffer(void)
{
        int16_t tmp;
        cli(); // stop all interrupts to avoid writing of new data during update of that packet.

        // update content of packet to NaviCtrl
        ToNaviCtrl.IntegralNick = (int16_t) (IntegralNick / 108);
        ToNaviCtrl.IntegralRoll  = (int16_t) (IntegralRoll  / 108);
        ToNaviCtrl.GyroHeading = YawGyroHeading / YAW_GYRO_DEG_FACTOR;
        ToNaviCtrl.GyroNick = Reading_GyroNick;
        ToNaviCtrl.GyroRoll = Reading_GyroRoll;
        ToNaviCtrl.GyroYaw = Reading_GyroYaw;
        ToNaviCtrl.AccNick = (int16_t) ACC_AMPLIFY * (NaviAccNick / NaviCntAcc);
        ToNaviCtrl.AccRoll =  (int16_t) ACC_AMPLIFY * (NaviAccRoll / NaviCntAcc);
        NaviCntAcc = 0; NaviAccNick = 0; NaviAccRoll = 0;

        switch(ToNaviCtrl.Command)
        {
                case SPI_CMD_USER:
                        ToNaviCtrl.Param.Byte[0] = FCParam.UserParam1;
                        ToNaviCtrl.Param.Byte[1] = FCParam.UserParam2;
                        ToNaviCtrl.Param.Byte[2] = FCParam.UserParam3;
                        ToNaviCtrl.Param.Byte[3] = FCParam.UserParam4;
                        ToNaviCtrl.Param.Byte[4] = FCParam.UserParam5;
                        ToNaviCtrl.Param.Byte[5] = FCParam.UserParam6;
                        ToNaviCtrl.Param.Byte[6] = FCParam.UserParam7;
                        ToNaviCtrl.Param.Byte[7] = FCParam.UserParam8;
                        ToNaviCtrl.Param.Byte[8] = MKFlags;
                        MKFlags &= ~(MKFLAG_CALIBRATE | MKFLAG_START); // calibrate and start are temporal states that are cleared immediately after transmitting
                        ToNaviCtrl.Param.Byte[9] = (uint8_t)UBat;
                        ToNaviCtrl.Param.Byte[10] = ParamSet.LowVoltageWarning;
                        ToNaviCtrl.Param.Byte[11] = GetActiveParamSet();
                        break;

                case SPI_CMD_PARAMETER1:
                        ToNaviCtrl.Param.Byte[0] = FCParam.NaviGpsModeControl;     // Parameters for the Naviboard
                        ToNaviCtrl.Param.Byte[1] = FCParam.NaviGpsGain;
                        ToNaviCtrl.Param.Byte[2] = FCParam.NaviGpsP;
                        ToNaviCtrl.Param.Byte[3] = FCParam.NaviGpsI;
                        ToNaviCtrl.Param.Byte[4] = FCParam.NaviGpsD;
                        ToNaviCtrl.Param.Byte[5] = FCParam.NaviGpsACC;
                        ToNaviCtrl.Param.Byte[6] = ParamSet.NaviGpsMinSat;
                        ToNaviCtrl.Param.Byte[7] = ParamSet.NaviStickThreshold;
                        ToNaviCtrl.Param.Byte[8] = 15; // MaxRadius
                        break;


                case SPI_CMD_STICK:
                        tmp = PPM_in[ParamSet.ChannelAssignment[CH_GAS]];  if(tmp > 127) tmp = 127; else if(tmp < -128) tmp = -128;
                        ToNaviCtrl.Param.Byte[0] = (int8_t) tmp;
                        tmp = PPM_in[ParamSet.ChannelAssignment[CH_YAW]]; if(tmp > 127) tmp = 127; else if(tmp < -128) tmp = -128;
                        ToNaviCtrl.Param.Byte[1] = (int8_t) tmp;
                        tmp = PPM_in[ParamSet.ChannelAssignment[CH_ROLL]]; if(tmp > 127) tmp = 127; else if(tmp < -128) tmp = -128;
                        ToNaviCtrl.Param.Byte[2] = (int8_t) tmp;
                        tmp = PPM_in[ParamSet.ChannelAssignment[CH_NICK]]; if(tmp > 127) tmp = 127; else if(tmp < -128) tmp = -128;
                        ToNaviCtrl.Param.Byte[3] = (int8_t) tmp;
                        ToNaviCtrl.Param.Byte[4] = (uint8_t) Poti1;
                        ToNaviCtrl.Param.Byte[5] = (uint8_t) Poti2;
                        ToNaviCtrl.Param.Byte[6] = (uint8_t) Poti3;
                        ToNaviCtrl.Param.Byte[7] = (uint8_t) Poti4;
                        ToNaviCtrl.Param.Byte[8] = (uint8_t) RC_Quality;
                        break;

                case SPI_CMD_CAL_COMPASS:
                        if(CompassCalState > 5)
                        {
                                CompassCalState = 0;
                                ToNaviCtrl.Param.Byte[0] = 5;
                        }
                        else
                        {
                                ToNaviCtrl.Param.Byte[0] = CompassCalState;
                        }
                        break;
        }


        sei(); // enable all interrupts

        // analyze content of packet from NaviCtrl if valid
        if (SPI_RxDataValid)
        {
                // update gps controls
                if(abs(FromNaviCtrl.GPS_Nick) < 512 && abs(FromNaviCtrl.GPS_Roll) < 512 && (ParamSet.GlobalConfig & CFG_GPS_ACTIVE))
                {
                        GPS_Nick        = FromNaviCtrl.GPS_Nick;
                        GPS_Roll        = FromNaviCtrl.GPS_Roll;
                }
                // update compass readings
                if(FromNaviCtrl.CompassHeading <= 360)
                {
                        CompassHeading = FromNaviCtrl.CompassHeading;
                }
                if(CompassHeading < 0) CompassOffCourse = 0;
                else CompassOffCourse = ((540 + CompassHeading - CompassCourse) % 360) - 180;
        // NaviCtrl wants to beep?
                if (FromNaviCtrl.BeepTime > BeepTime && !CompassCalState) BeepTime = FromNaviCtrl.BeepTime;

                switch (FromNaviCtrl.Command)
                {
                        case  SPI_CMD_OSD_DATA:
                                //                                ToFlightCtrl.Param.Byte[0] = OsdBar;
                                //                                ToFlightCtrl.Param.Int[1]  = Distance;
                                break;

                        case  SPI_CMD_GPS_POS:
                                //                                ToFlightCtrl.Param.Long[0]  = GPS_Data.Longitude;
                                //                                ToFlightCtrl.Param.Long[1]  = GPS_Data.Latitude;
                                break;

                        case  SPI_CMD_GPS_TARGET:
                                //                                ToFlightCtrl.Param.Long[0]  = GPS_Data.TargetLongitude;
                                //                                ToFlightCtrl.Param.Long[1]  = GPS_Data.TargetLatitude;
                                break;

                        default:
                                break;
                }
        }
        else // no valid data from NaviCtrl
        {
                // disable GPS control
                GPS_Nick = 0;
                GPS_Roll = 0;
        }
}



/*********************************************/
/*  Start Transmission of packet to NaviCtrl */
/*********************************************/
void SPI_StartTransmitPacket(void)
{

        if (!SPITransferCompleted) return; // return immediately if transfer is in progress
        else // transmission was completed
        {
                SLAVE_SELECT_PORT &=  ~(1 << SPI_SLAVE_SELECT);  // Select slave

                // cyclic commands
                ToNaviCtrl.Command = SPI_CommandSequence[SPI_CommandCounter++];
                if (SPI_CommandCounter >= sizeof(SPI_CommandSequence)) SPI_CommandCounter = 0;

                SPITransferCompleted = 0; // transfer is in progress
                UpdateSPI_Buffer();    // update data in ToNaviCtrl

                SPI_TxBufferIndex = 1; //proceed with 2nd byte

                // -- Debug-Output ---
                //----
                asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop");            asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop");
                asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop");            asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop");
                asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop");            asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop");
                ToNaviCtrl.Chksum = ToNaviCtrl.Sync1; // init checksum
                SPDR = ToNaviCtrl.Sync1; // send first byte
        }
}

//------------------------------------------------------
// This is the spi data transfer between FlightCtrl and NaviCtrl
// Every time this routine is called within the mainloop one byte of the packet to
// the NaviCtrl and one byte of the packet from the NaviCtrl is possible transfered

void SPI_TransmitByte(void)
{
        static SPI_RXState_t SPI_RXState = SPI_SYNC1;
        uint8_t rxdata;
        static uint8_t rxchksum;

        if (SPITransferCompleted) return;  // return immediatly if transfer was completed
        if (!(SPSR & (1 << SPIF))) return; // return if no SPI-IRQ pending
        SendSPI = 4; // mait 4 * 0.102 ms for the next call of SPI_TransmitByte() in the main loop

        SLAVE_SELECT_PORT |=  (1 << SPI_SLAVE_SELECT);   // DeselectSlave

        rxdata = SPDR; // save spi data register

        switch (SPI_RXState)
        {
                case SPI_SYNC1: // first sync byte
                        SPI_RxBufferIndex = 0; // set pointer to start of rx buffer
                        rxchksum = rxdata; // initialize checksum
                        if (rxdata == SPI_RXSYNCBYTE1 )
                        {       // 1st Syncbyte found
                                SPI_RXState  = SPI_SYNC2; // trigger to state for second sync byte
                        }
                        break;

                case SPI_SYNC2: // second sync byte
                        if (rxdata == SPI_RXSYNCBYTE2)
                        {       // 2nd Syncbyte found
                                rxchksum += rxdata; // update checksum
                                SPI_RXState  = SPI_DATA;   // trigger to state for second sync byte
                        }
                        else // 2nd Syncbyte not found
                        {
                                SPI_RXState  = SPI_SYNC1; // jump back to 1st sync byte
                        }
                        break;

                case SPI_DATA: // data bytes
                        SPI_RxBuffer[SPI_RxBufferIndex++] = rxdata;  // copy data byte to spi buffer
                        // if all bytes are received of a packet from the NaviCtrl
                        if (SPI_RxBufferIndex >= SPI_RXBUFFER_LEN)
                        {   // last byte transfered is the checksum of the packet
                                if (rxdata == rxchksum) // checksum matching?
                                {
                                        // copy SPI_RxBuffer -> FromFlightCtrl
                                        uint8_t *ptr = (uint8_t *)&FromNaviCtrl;
                                        cli();
                                        memcpy(ptr, (uint8_t *) SPI_RxBuffer, sizeof(FromNaviCtrl));
                                        sei();
                                        SPI_RxDataValid = 1;
                                        DebugOut.Analog[18]++;
                                }
                                else
                                {   // checksum does not match
                                        DebugOut.Analog[17]++;
                                        SPI_RxDataValid = 0; // reset valid flag
                                }
                                SPI_RXState  = SPI_SYNC1; // reset state sync
                        }
                        else // not all bytes transfered
                        {
                                rxchksum += rxdata; // update checksum
                        }
                        break;
        }// eof switch(SPI_RXState)

    // if still some bytes left for transmission to NaviCtrl
        if (SPI_TxBufferIndex < SPI_TXBUFFER_LEN)
        {
                SLAVE_SELECT_PORT &=  ~(1 << SPI_SLAVE_SELECT);  // SelectSlave
                asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop");
                asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop");
                asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop"); asm volatile ("nop");

                SPDR = SPI_TxBuffer[SPI_TxBufferIndex]; // transmit byte
                ToNaviCtrl.Chksum += SPI_TxBuffer[SPI_TxBufferIndex]; // update checksum for everey byte that was sent
                SPI_TxBufferIndex++;
        }
        else
        {
                //Transfer of all bytes of the packet to NaviCtrl completed
                SPITransferCompleted = 1;
        }
}