Subversion Repositories BL-Ctrl

Rev

Rev 80 | Blame | Compare with Previous | Last modification | View Log | RSS feed

// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Regler für Brushless-Motoren
// + ATMEGA8 mit 8MHz
// + (c) 01.2007 Holger Buss
// + Nur für den privaten Gebrauch
// + Keine Garantie auf Fehlerfreiheit
// + Kommerzielle Nutzung nur mit meiner Zustimmung
// + Der Code ist für die Hardware BL_Ctrl V1.0 entwickelt worden
// + www.mikrocontroller.com
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

#include "main.h"
#include "uart.h"

#define MAX_SENDE_BUFF     100
#define MAX_EMPFANGS_BUFF  100

unsigned volatile char SIO_Sollwert = 0;
unsigned volatile char SioTmp = 0;
unsigned volatile char SendeBuffer[MAX_SENDE_BUFF];
unsigned volatile char RxdBuffer[MAX_EMPFANGS_BUFF];
unsigned volatile char NeuerDatensatzEmpfangen = 0;
unsigned volatile char UebertragungAbgeschlossen = 1;
unsigned char MeineSlaveAdresse;
unsigned char MotorTest[6] = {0,0,0,0,0,0};
unsigned volatile char AnzahlEmpfangsBytes = 0;

struct str_DebugOut    DebugOut;


int Debug_Timer;


SIGNAL(INT_VEC_TX)
{
}

void SendUart(void)
{
 static unsigned int ptr = 0;
 unsigned char tmp_tx;
 if(!(UCSRA & 0x40)) return;
 if(!UebertragungAbgeschlossen)  
  {
   ptr++;                    // die [0] wurde schon gesendet
   tmp_tx = SendeBuffer[ptr];  
   if((tmp_tx == '\r') || (ptr == MAX_SENDE_BUFF))
    {
     ptr = 0;
     UebertragungAbgeschlossen = 1;
    }
   USR |= (1<TXC);
   UDR = tmp_tx;
  }
  else ptr = 0;
}

// --------------------------------------------------------------------------
void Decode64(unsigned char *ptrOut, unsigned char len, unsigned char ptrIn,unsigned char max)  // Wohin mit den Daten; Wie lang; Wo im RxdBuffer
{
 unsigned char a,b,c,d;
 unsigned char ptr = 0;
 unsigned char x,y,z;
 while(len)
  {
   a = RxdBuffer[ptrIn++] - '=';
   b = RxdBuffer[ptrIn++] - '=';
   c = RxdBuffer[ptrIn++] - '=';
   d = RxdBuffer[ptrIn++] - '=';
   if(ptrIn > max - 2) break;     // nicht mehr Daten verarbeiten, als empfangen wurden

   x = (a << 2) | (b >> 4);
   y = ((b & 0x0f) << 4) | (c >> 2);
   z = ((c & 0x03) << 6) | d;

   if(len--) ptrOut[ptr++] = x; else break;
   if(len--) ptrOut[ptr++] = y; else break;
   if(len--) ptrOut[ptr++] = z; else break;
  }

}


//+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
//++ Empfangs-Part der Datenübertragung
//+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
SIGNAL(INT_VEC_RX)
{
 
#if  X3D_SIO == 1
 static unsigned char serPacketCounter = 100;
    SioTmp = UDR;
        if(SioTmp == 0xF5)     // Startzeichen
         {
          serPacketCounter = 0;
         }
        else
         {
          if(++serPacketCounter == MotorAdresse) // (1-6)
          {
                SIO_Sollwert = SioTmp;
            SIO_Timeout = 200; // werte für 200ms gültig
          }
          else
          {
           if(serPacketCounter > 100) serPacketCounter = 100;
                  }
         }
#else
 static unsigned int crc;
 static unsigned char crc1,crc2,buf_ptr;
 static unsigned char UartState = 0;
 unsigned char CrcOkay = 0;
 
 SioTmp = UDR;
 if(buf_ptr >= MAX_EMPFANGS_BUFF)    UartState = 0;
 if(SioTmp == '\r' && UartState == 2)
  {
   UartState = 0;
   crc -= RxdBuffer[buf_ptr-2];
   crc -= RxdBuffer[buf_ptr-1];
   crc %= 4096;
   crc1 = '=' + crc / 64;
   crc2 = '=' + crc % 64;
   CrcOkay = 0;
   if((crc1 == RxdBuffer[buf_ptr-2]) && (crc2 == RxdBuffer[buf_ptr-1])) CrcOkay = 1; else { CrcOkay = 0; };
   if(CrcOkay) // Datensatz schon verarbeitet
    {
     //NeuerDatensatzEmpfangen = 1;
         AnzahlEmpfangsBytes = buf_ptr;
     
     RxdBuffer[buf_ptr] = '\r';
         if(/*(RxdBuffer[1] == MeineSlaveAdresse || (RxdBuffer[1] == 'a')) && */(RxdBuffer[2] == 'R')) wdt_enable(WDTO_250MS); // Reset-Commando
     uart_putchar(RxdBuffer[2]);         
         if (RxdBuffer[2] == 't') // Motortest
            { Decode64((unsigned char *) &MotorTest[0],sizeof(MotorTest),3,AnzahlEmpfangsBytes);
                          SIO_Sollwert = MotorTest[MotorAdresse - 1];
              SIO_Timeout = 500; // werte für 500ms gültig
 
                        }
        }                                
  }
  else
  switch(UartState)
  {
   case 0:
          if(SioTmp == '#' && !NeuerDatensatzEmpfangen) UartState = 1;  // Startzeichen und Daten schon verarbeitet
                  buf_ptr = 0;
                  RxdBuffer[buf_ptr++] = SioTmp;
                  crc = SioTmp;
          break;
   case 1: // Adresse auswerten
                  UartState++;
                  RxdBuffer[buf_ptr++] = SioTmp;
                  crc += SioTmp;
                  break;
   case 2: //  Eingangsdaten sammeln
                  RxdBuffer[buf_ptr] = SioTmp;
                  if(buf_ptr < MAX_EMPFANGS_BUFF) buf_ptr++;
                  else UartState = 0;
                  crc += SioTmp;
                  break;
   default:
          UartState = 0;
          break;
  }

         
#endif
};


// --------------------------------------------------------------------------
void AddCRC(unsigned int wieviele)
{
 unsigned int tmpCRC = 0,i;
 for(i = 0; i < wieviele;i++)
  {
   tmpCRC += SendeBuffer[i];
  }
   tmpCRC %= 4096;
   SendeBuffer[i++] = '=' + tmpCRC / 64;
   SendeBuffer[i++] = '=' + tmpCRC % 64;
   SendeBuffer[i++] = '\r';
  UebertragungAbgeschlossen = 0;
  UDR = SendeBuffer[0];
}


// --------------------------------------------------------------------------
void SendOutData(unsigned char cmd,unsigned char modul, unsigned char *snd, unsigned char len)
{
 unsigned int pt = 0;
 unsigned char a,b,c;
 unsigned char ptr = 0;
 

 SendeBuffer[pt++] = '#';               // Startzeichen
 SendeBuffer[pt++] = modul;             // Adresse (a=0; b=1,...)
 SendeBuffer[pt++] = cmd;                       // Commando

 while(len)
  {
   if(len) { a = snd[ptr++]; len--;} else a = 0;
   if(len) { b = snd[ptr++]; len--;} else b = 0;
   if(len) { c = snd[ptr++]; len--;} else c = 0;
   SendeBuffer[pt++] = '=' + (a >> 2);
   SendeBuffer[pt++] = '=' + (((a & 0x03) << 4) | ((b & 0xf0) >> 4));
   SendeBuffer[pt++] = '=' + (((b & 0x0f) << 2) | ((c & 0xc0) >> 6));
   SendeBuffer[pt++] = '=' + ( c & 0x3f);
  }
 AddCRC(pt);
}



//############################################################################
//Routine für die Serielle Ausgabe
int uart_putchar (char c)
//############################################################################
{
        if (c == '\n')
                uart_putchar('\r');
        //Warten solange bis Zeichen gesendet wurde
        loop_until_bit_is_set(USR, UDRE);
        //Ausgabe des Zeichens
        UDR = c;
       
        return (0);
}

// --------------------------------------------------------------------------
void WriteProgramData(unsigned int pos, unsigned char wert)
{
}

//############################################################################
//INstallation der Seriellen Schnittstelle
void UART_Init (void)
//############################################################################
{
        //Enable TXEN im Register UCR TX-Data Enable & RX Enable

        UCR=(1 << TXEN) | (1 << RXEN);
    // UART Double Speed (U2X)
        USR   |= (1<<U2X);          
        // RX-Interrupt Freigabe

        UCSRB |= (1<<RXCIE);    // serieller Empfangsinterrupt      

        // TX-Interrupt Freigabe
//      UCSRB |= (1<<TXCIE);          

        //Teiler wird gesetzt
        UBRR= (SYSCLK / (BAUD_RATE * 8L) -1 );
        //öffnet einen Kanal für printf (STDOUT)
        fdevopen (uart_putchar, NULL);
    Debug_Timer = SetDelay(200);  
    // Version beim Start ausgeben (nicht schön, aber geht... )
        uart_putchar ('\n');uart_putchar ('B');uart_putchar ('L');uart_putchar (':');
        uart_putchar ('V');uart_putchar (0x30 + VERSION_HAUPTVERSION);uart_putchar ('.');uart_putchar (0x30 + VERSION_NEBENVERSION/10); uart_putchar (0x30 + VERSION_NEBENVERSION%10);
    uart_putchar ('\n');uart_putchar('H');uart_putchar('W');uart_putchar (':');uart_putchar('1');uart_putchar('.');uart_putchar ((0x30-10) + HwVersion);
        uart_putchar ('\n');uart_putchar ('A');uart_putchar ('D');uart_putchar ('R'); uart_putchar (':'); uart_putchar (0x30 + MotorAdresse);

}




//---------------------------------------------------------------------------------------------
void DatenUebertragung(void)  
{
 if((CheckDelay(Debug_Timer) && UebertragungAbgeschlossen))      // im Singlestep-Betrieb in jedem Schtitt senden
         {
          SendOutData('D',MeineSlaveAdresse,(unsigned char *) &DebugOut,sizeof(DebugOut));
          Debug_Timer = SetDelay(50);   // Sendeintervall
         }
}