Subversion Repositories FlightCtrl

Compare Revisions

Ignore whitespace Rev 2383 → Rev 2384

/branches/V2.01a_ACC-HH_MartinR/capacity.c
0,0 → 1,144
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + www.MikroKopter.com
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Software Nutzungsbedingungen (english version: see below)
// + der Fa. HiSystems GmbH, Flachsmeerstrasse 2, 26802 Moormerland - nachfolgend Lizenzgeber genannt -
// + Der Lizenzgeber räumt dem Kunden ein nicht-ausschließliches, zeitlich und räumlich* unbeschränktes Recht ein, die im den
// + Mikrocontroller verwendete Firmware für die Hardware Flight-Ctrl, Navi-Ctrl, BL-Ctrl, MK3Mag & PC-Programm MikroKopter-Tool
// + - nachfolgend Software genannt - nur für private Zwecke zu nutzen.
// + Der Einsatz dieser Software ist nur auf oder mit Produkten des Lizenzgebers zulässig.
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Die vom Lizenzgeber gelieferte Software ist urheberrechtlich geschützt. Alle Rechte an der Software sowie an sonstigen im
// + Rahmen der Vertragsanbahnung und Vertragsdurchführung überlassenen Unterlagen stehen im Verhältnis der Vertragspartner ausschließlich dem Lizenzgeber zu.
// + Die in der Software enthaltenen Copyright-Vermerke, Markenzeichen, andere Rechtsvorbehalte, Seriennummern sowie
// + sonstige der Programmidentifikation dienenden Merkmale dürfen vom Kunden nicht verändert oder unkenntlich gemacht werden.
// + Der Kunde trifft angemessene Vorkehrungen für den sicheren Einsatz der Software. Er wird die Software gründlich auf deren
// + Verwendbarkeit zu dem von ihm beabsichtigten Zweck testen, bevor er diese operativ einsetzt.
// + Die Haftung des Lizenzgebers wird - soweit gesetzlich zulässig - begrenzt in Höhe des typischen und vorhersehbaren
// + Schadens. Die gesetzliche Haftung bei Personenschäden und nach dem Produkthaftungsgesetz bleibt unberührt. Dem Lizenzgeber steht jedoch der Einwand
// + des Mitverschuldens offen.
// + Der Kunde trifft angemessene Vorkehrungen für den Fall, dass die Software ganz oder teilweise nicht ordnungsgemäß arbeitet.
// + Er wird die Software gründlich auf deren Verwendbarkeit zu dem von ihm beabsichtigten Zweck testen, bevor er diese operativ einsetzt.
// + Der Kunde wird er seine Daten vor Einsatz der Software nach dem Stand der Technik sichern.
// + Der Kunde ist darüber unterrichtet, dass der Lizenzgeber seine Daten im zur Vertragsdurchführung erforderlichen Umfang
// + und auf Grundlage der Datenschutzvorschriften erhebt, speichert, verarbeitet und, sofern notwendig, an Dritte übermittelt.
// + *) Die räumliche Nutzung bezieht sich nur auf den Einsatzort, nicht auf die Reichweite der programmierten Software.
// + #### ENDE DER NUTZUNGSBEDINGUNGEN ####'
// + Hinweis: Informationen über erweiterte Nutzungsrechte (wie z.B. Nutzung für nicht-private Zwecke) sind auf Anfrage per Email an info(@)hisystems.de verfügbar.
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + Software LICENSING TERMS
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
// + of HiSystems GmbH, Flachsmeerstrasse 2, 26802 Moormerland, Germany - the Licensor -
// + The Licensor grants the customer a non-exclusive license to use the microcontroller firmware of the Flight-Ctrl, Navi-Ctrl, BL-Ctrl, and MK3Mag hardware
// + (the Software) exclusively for private purposes. The License is unrestricted with respect to time and territory*.
// + The Software may only be used with the Licensor's products.
// + The Software provided by the Licensor is protected by copyright. With respect to the relationship between the parties to this
// + agreement, all rights pertaining to the Software and other documents provided during the preparation and execution of this
// + agreement shall be the property of the Licensor.
// + The information contained in the Software copyright notices, trademarks, other legal reservations, serial numbers and other
// + features that can be used to identify the program may not be altered or defaced by the customer.
// + The customer shall be responsible for taking reasonable precautions
// + for the safe use of the Software. The customer shall test the Software thoroughly regarding its suitability for the
// + intended purpose before implementing it for actual operation. The Licensor's liability shall be limited to the extent of typical and
// + foreseeable damage to the extent permitted by law, notwithstanding statutory liability for bodily injury and product
// + liability. However, the Licensor shall be entitled to the defense of contributory negligence.
// + The customer will take adequate precautions in the case, that the software is not working properly. The customer will test
// + the software for his purpose before any operational usage. The customer will backup his data before using the software.
// + The customer understands that the Licensor collects, stores and processes, and, where required, forwards, customer data
// + to third parties to the extent necessary for executing the agreement, subject to applicable data protection and privacy regulations.
// + *) The territory aspect only refers to the place where the Software is used, not its programmed range.
// + #### END OF LICENSING TERMS ####
// + Note: For information on license extensions (e.g. commercial use), please contact us at info(@)hisystems.de.
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 
#include "capacity.h"
#include "twimaster.h"
#include "main.h"
#include "timer0.h"
#include "analog.h"
 
#define CAPACITY_UPDATE_INTERVAL 10 // 10 ms
#define FC_OFFSET_CURRENT 5 // calculate with a current of 0.5A
#define BL_OFFSET_CURRENT 2 // calculate with a current of 0.2A
 
// global varialbles
unsigned short update_timer = 0;
Capacity_t Capacity;
 
// initialize capacity calculation
void Capacity_Init(void)
{
Capacity.ActualCurrent = 0;
Capacity.UsedCapacity = 0;
Capacity.ActualPower = 0;
Capacity.MinOfMaxPWM = 0;
update_timer = SetDelay(CAPACITY_UPDATE_INTERVAL);
}
 
 
// called in main loop at a regular interval
void Capacity_Update(void)
{
unsigned short Current, SetSum; // max value will be 255 * 12 = 3060
static unsigned short SubCounter = 0;
static unsigned short CurrentOffset = 0;
static unsigned long SumCurrentOffset = 0;
unsigned char i, NumOfMotors, MinOfMaxPWM;
 
if(CheckDelay(update_timer))
{
update_timer += CAPACITY_UPDATE_INTERVAL; // do not use SetDelay to avoid timing leaks
// determine sum of all present BL currents and setpoints
Current = 0;
SetSum = 0;
NumOfMotors = 0;
MinOfMaxPWM = 255;
for(i = 0; i < MAX_MOTORS; i++)
{
if(Motor[i].State & MOTOR_STATE_PRESENT_MASK)
{
NumOfMotors++;
Current += (unsigned int)(Motor[i].Current);
SetSum += (unsigned int)(Motor[i].SetPoint);
if(Motor[i].MaxPWM < MinOfMaxPWM) MinOfMaxPWM = Motor[i].MaxPWM;
}
}
Capacity.MinOfMaxPWM = MinOfMaxPWM;
 
if(SetSum == 0) // if all setpoints are 0
{ // determine offsets of motor currents
#define CURRENT_AVERAGE 8 // 8bit = 256 * 10 ms = 2.56s average time
CurrentOffset = (unsigned int)(SumCurrentOffset>>CURRENT_AVERAGE);
SumCurrentOffset -= CurrentOffset;
SumCurrentOffset += Current;
// after averaging set current to static offset
Current = FC_OFFSET_CURRENT;
}
else // some motors are running, includes also motor test condition, where "MotorRunning" is false
{ // subtract offset
if(Current > CurrentOffset) Current -= CurrentOffset;
else Current = 0;
// add the FC and BL Offsets
Current += FC_OFFSET_CURRENT + NumOfMotors * BL_OFFSET_CURRENT;
}
 
// update actual Current
Capacity.ActualCurrent = Current;
// update actual Power
if(Current < 255) Capacity.ActualPower = (UBat * Current) / 100; // in W higher resolution
else Capacity.ActualPower = (UBat * (Current/4)) / 25; // in W
 
// update used capacity
SubCounter += Current;
 
// 100mA * 1ms * CAPACITY_UPDATE_INTERVAL = 1 mA * 100 ms * CAPACITY_UPDATE_INTERVAL
// = 1mA * 0.1s * CAPACITY_UPDATE_INTERVAL = 1mA * 1min / (600 / CAPACITY_UPDATE_INTERVAL)
// = 1mAh / (36000 / CAPACITY_UPDATE_INTERVAL)
#define SUB_COUNTER_LIMIT (36000 / CAPACITY_UPDATE_INTERVAL)
if(SubCounter > SUB_COUNTER_LIMIT)
{
Capacity.UsedCapacity++; // we have one mAh more
SubCounter -= SUB_COUNTER_LIMIT; // keep the remaining sub part
}
} // EOF check delay update timer
}