| 0,0 → 1,215 |
|---|
| /*####################################################################################### |
| Flight Control |
| #######################################################################################*/ |
| |
| #ifndef _FC_H |
| #define _FC_H |
| //#define GIER_GRAD_FAKTOR 1291L // Abhängigkeit zwischen GyroIntegral und Winkel |
| //#define GIER_GRAD_FAKTOR 1160L |
| extern long GIER_GRAD_FAKTOR; // Abhängigkeit zwischen GyroIntegral und Winkel |
| #define STICK_GAIN 4 |
| |
| #define FCFLAG_MOTOR_RUN 0x01 |
| #define FCFLAG_FLY 0x02 |
| #define FCFLAG_CALIBRATE 0x04 |
| #define FCFLAG_START 0x08 |
| #define FCFLAG_NOTLANDUNG 0x10 |
| #define FCFLAG_LOWBAT 0x20 |
| #define FCFLAG_SPI_RX_ERR 0x40 |
| #define FCFLAG_I2CERR 0x80 |
| |
| #define Poti1 Poti[0] |
| #define Poti2 Poti[1] |
| #define Poti3 Poti[2] |
| #define Poti4 Poti[3] |
| #define Poti5 Poti[4] |
| #define Poti6 Poti[5] |
| #define Poti7 Poti[6] |
| #define Poti8 Poti[7] |
| |
| |
| #define CHECK_MIN_MAX(wert,min,max) {if(wert < min) wert = min; else if(wert > max) wert = max;} |
| |
| extern volatile unsigned char FCFlags; |
| extern volatile unsigned int I2CTimeout; |
| extern unsigned char Sekunde,Minute; |
| extern unsigned int BaroExpandActive; |
| extern long IntegralNick,IntegralNick2; |
| extern long IntegralRoll,IntegralRoll2; |
| //extern int IntegralNick,IntegralNick2; |
| //extern int IntegralRoll,IntegralRoll2; |
| extern unsigned char Poti[9]; |
| |
| extern long Mess_IntegralNick,Mess_IntegralNick2; |
| extern long Mess_IntegralRoll,Mess_IntegralRoll2; |
| extern long IntegralAccNick,IntegralAccRoll; |
| extern volatile long Mess_Integral_Hoch; |
| extern long Integral_Gier,Mess_Integral_Gier,Mess_Integral_Gier2; |
| extern int KompassValue; |
| extern int KompassStartwert; |
| extern int KompassRichtung; |
| extern int TrimNick, TrimRoll; |
| extern long ErsatzKompass; |
| extern int ErsatzKompassInGrad; // Kompasswert in Grad |
| extern long HoehenWert; |
| extern long SollHoehe; |
| extern int MesswertNick,MesswertRoll,MesswertGier; |
| extern int AdNeutralNick,AdNeutralRoll,AdNeutralGier, Mittelwert_AccNick, Mittelwert_AccRoll; |
| extern int NeutralAccX, NeutralAccY,Mittelwert_AccHoch; |
| extern unsigned char HoehenReglerAktiv; |
| extern volatile float NeutralAccZ; |
| extern long Umschlag180Nick, Umschlag180Roll; |
| extern signed int ExternStickNick,ExternStickRoll,ExternStickGier; |
| extern unsigned char Parameter_UserParam1,Parameter_UserParam2,Parameter_UserParam3,Parameter_UserParam4,Parameter_UserParam5,Parameter_UserParam6,Parameter_UserParam7,Parameter_UserParam8; |
| extern int NaviAccNick,NaviAccRoll,NaviCntAcc; |
| extern unsigned int modell_fliegt; |
| void MotorRegler(void); |
| void SendMotorData(void); |
| void CalibrierMittelwert(void); |
| void Mittelwert(void); |
| void SetNeutral(void); |
| void Piep(unsigned char Anzahl, unsigned int dauer); |
| |
| extern unsigned char h,m,s; |
| extern volatile unsigned char Timeout ; |
| extern unsigned char CosinusNickWinkel, CosinusRollWinkel; |
| extern int DiffNick,DiffRoll; |
| //extern int Poti1, Poti2, Poti3, Poti4; |
| extern volatile unsigned char SenderOkay; |
| extern volatile unsigned char SenderRSSI; |
| extern int StickNick,StickRoll,StickGier; |
| extern char MotorenEin; |
| extern void DefaultKonstanten1(void); |
| extern void DefaultKonstanten2(void); |
| extern void DefaultKonstanten3(void); |
| extern void DefaultStickMapping(void); |
| extern unsigned char Parameter_Servo3,Parameter_Servo4,Parameter_Servo5; |
| extern char VarioCharacter; |
| |
| |
| #define STRUCT_PARAM_LAENGE sizeof(EE_Parameter) |
| struct mk_param_struct |
| { |
| unsigned char Kanalbelegung[12]; // GAS[0], GIER[1],NICK[2], ROLL[3], POTI1, POTI2, POTI3 |
| unsigned char GlobalConfig; // 0x01=Höhenregler aktiv,0x02=Kompass aktiv, 0x04=GPS aktiv, 0x08=Heading Hold aktiv |
| unsigned char Hoehe_MinGas; // Wert : 0-100 |
| unsigned char Luftdruck_D; // Wert : 0-250 |
| unsigned char MaxHoehe; // Wert : 0-32 |
| unsigned char Hoehe_P; // Wert : 0-32 |
| unsigned char Hoehe_Verstaerkung; // Wert : 0-50 |
| unsigned char Hoehe_ACC_Wirkung; // Wert : 0-250 |
| unsigned char Hoehe_HoverBand; // Wert : 0-250 |
| unsigned char Hoehe_GPS_Z; // Wert : 0-250 |
| unsigned char Hoehe_StickNeutralPoint;// Wert : 0-250 |
| unsigned char Stick_P; // Wert : 1-6 |
| unsigned char Stick_D; // Wert : 0-64 |
| unsigned char Gier_P; // Wert : 1-20 |
| unsigned char Gas_Min; // Wert : 0-32 |
| unsigned char Gas_Max; // Wert : 33-250 |
| unsigned char GyroAccFaktor; // Wert : 1-64 |
| unsigned char KompassWirkung; // Wert : 0-32 |
| unsigned char Gyro_P; // Wert : 10-250 |
| unsigned char Gyro_I; // Wert : 0-250 |
| unsigned char Gyro_D; // Wert : 0-250 |
| unsigned char Gyro_Gier_P; // Wert : 10-250 |
| unsigned char Gyro_Gier_I; // Wert : 0-250 |
| unsigned char UnterspannungsWarnung; // Wert : 0-250 |
| unsigned char NotGas; // Wert : 0-250 //Gaswert bei Empängsverlust |
| unsigned char NotGasZeit; // Wert : 0-250 // Zeitbis auf NotGas geschaltet wird, wg. Rx-Problemen |
| unsigned char Receiver; // 0= Summensignal, 1= Spektrum, 2 =Jeti, 3=ACT DSL, 4=ACT S3D |
| unsigned char I_Faktor; // Wert : 0-250 |
| unsigned char UserParam1; // Wert : 0-250 |
| unsigned char UserParam2; // Wert : 0-250 |
| unsigned char UserParam3; // Wert : 0-250 |
| unsigned char UserParam4; // Wert : 0-250 |
| unsigned char ServoNickControl; // Wert : 0-250 // Stellung des Servos |
| unsigned char ServoNickComp; // Wert : 0-250 // Einfluss Gyro/Servo |
| unsigned char ServoNickMin; // Wert : 0-250 // Anschlag |
| unsigned char ServoNickMax; // Wert : 0-250 // Anschlag |
| //--- Seit V0.75 |
| unsigned char ServoRollControl; // Wert : 0-250 // Stellung des Servos |
| unsigned char ServoRollComp; // Wert : 0-250 |
| unsigned char ServoRollMin; // Wert : 0-250 |
| unsigned char ServoRollMax; // Wert : 0-250 |
| //--- |
| unsigned char ServoNickRefresh; // Speed of the Servo |
| unsigned char Servo3; // Value or mapping of the Servo Output |
| unsigned char Servo4; // Value or mapping of the Servo Output |
| unsigned char Servo5; // Value or mapping of the Servo Output |
| unsigned char LoopGasLimit; // Wert: 0-250 max. Gas während Looping |
| unsigned char LoopThreshold; // Wert: 0-250 Schwelle für Stickausschlag |
| unsigned char LoopHysterese; // Wert: 0-250 Hysterese für Stickausschlag |
| unsigned char AchsKopplung1; // Wert: 0-250 Faktor, mit dem Gier die Achsen Roll und Nick koppelt (NickRollMitkopplung) |
| unsigned char AchsKopplung2; // Wert: 0-250 Faktor, mit dem Nick und Roll verkoppelt werden |
| unsigned char CouplingYawCorrection; // Wert: 0-250 Faktor, mit dem Nick und Roll verkoppelt werden |
| unsigned char WinkelUmschlagNick; // Wert: 0-250 180°-Punkt |
| unsigned char WinkelUmschlagRoll; // Wert: 0-250 180°-Punkt |
| unsigned char GyroAccAbgleich; // 1/k (Koppel_ACC_Wirkung) |
| unsigned char Driftkomp; |
| unsigned char DynamicStability; |
| unsigned char UserParam5; // Wert : 0-250 |
| unsigned char UserParam6; // Wert : 0-250 |
| unsigned char UserParam7; // Wert : 0-250 |
| unsigned char UserParam8; // Wert : 0-250 |
| //---Output --------------------------------------------- |
| unsigned char J16Bitmask; // for the J16 Output |
| unsigned char J16Timing; // for the J16 Output |
| unsigned char J17Bitmask; // for the J17 Output |
| unsigned char J17Timing; // for the J17 Output |
| // seit version V0.75c |
| unsigned char WARN_J16_Bitmask; // for the J16 Output |
| unsigned char WARN_J17_Bitmask; // for the J17 Output |
| //---NaviCtrl--------------------------------------------- |
| unsigned char NaviGpsModeControl; // Parameters for the Naviboard |
| unsigned char NaviGpsGain; |
| unsigned char NaviGpsP; |
| unsigned char NaviGpsI; |
| unsigned char NaviGpsD; |
| unsigned char NaviGpsPLimit; |
| unsigned char NaviGpsILimit; |
| unsigned char NaviGpsDLimit; |
| unsigned char NaviGpsACC; |
| unsigned char NaviGpsMinSat; |
| unsigned char NaviStickThreshold; |
| unsigned char NaviWindCorrection; |
| unsigned char NaviSpeedCompensation; |
| unsigned char NaviOperatingRadius; |
| unsigned char NaviAngleLimitation; |
| unsigned char NaviPH_LoginTime; |
| //---Ext.Ctrl--------------------------------------------- |
| unsigned char ExternalControl; // for serial Control |
| //------------------------------------------------ |
| unsigned char BitConfig; // (war Loop-Cfg) Bitcodiert: 0x01=oben, 0x02=unten, 0x04=links, 0x08=rechts / wird getrennt behandelt |
| unsigned char ServoCompInvert; // // 0x01 = Nick, 0x02 = Roll 0 oder 1 // WICHTIG!!! am Ende lassen |
| unsigned char ExtraConfig; // bitcodiert |
| char Name[12]; |
| }; |
| |
| struct |
| { |
| char Revision; |
| char Name[12]; |
| signed char Motor[16][4]; |
| } Mixer; |
| |
| extern struct mk_param_struct EE_Parameter; |
| extern unsigned char Parameter_Luftdruck_D; |
| extern unsigned char Parameter_MaxHoehe; |
| extern unsigned char Parameter_Hoehe_P; |
| extern unsigned char Parameter_Hoehe_ACC_Wirkung; |
| extern unsigned char Parameter_KompassWirkung; |
| extern unsigned char Parameter_Gyro_P; |
| extern unsigned char Parameter_Gyro_I; |
| extern unsigned char Parameter_Gier_P; |
| extern unsigned char Parameter_ServoNickControl; |
| extern unsigned char Parameter_ServoRollControl; |
| extern unsigned char Parameter_AchsKopplung1; |
| extern unsigned char Parameter_AchsKopplung2; |
| //extern unsigned char Parameter_AchsGegenKopplung1; |
| extern unsigned char Parameter_J16Bitmask; // for the J16 Output |
| extern unsigned char Parameter_J16Timing; // for the J16 Output |
| extern unsigned char Parameter_J17Bitmask; // for the J17 Output |
| extern unsigned char Parameter_J17Timing; // for the J17 Output |
| extern signed char MixerTable[MAX_MOTORS][4]; |
| #endif //_FC_H |
| |