Rev 1960 | Rev 1965 | Go to most recent revision | Details | Compare with Previous | Last modification | View Log | RSS feed
| Rev | Author | Line No. | Line |
|---|---|---|---|
| 1612 | dongfang | 1 | //#include "ENC-03_FC1.3.h" |
| 2 | #include "printf_P.h" |
||
| 3 | #include "analog.h" |
||
| 4 | #include "twimaster.h" |
||
| 5 | #include "configuration.h" |
||
| 6 | #include "timer0.h" |
||
| 7 | |||
| 8 | #define PITCHROLL_MINLIMIT GYRO_SUMMATION_FACTOR_PITCHROLL * 510 |
||
| 9 | #define PITCHROLL_MAXLIMIT GYRO_SUMMATION_FACTOR_PITCHROLL * 515 |
||
| 10 | |||
| 1821 | - | 11 | const uint8_t GYRO_REVERSED[3] = { 0, 0, 1 }; |
| 12 | const uint8_t ACC_REVERSED[3] = { 0, 1, 0 }; |
||
| 1612 | dongfang | 13 | |
| 14 | // void gyro_init(void) {} |
||
| 15 | void gyro_calibrate(void) { |
||
| 1821 | - | 16 | uint8_t i, axis, factor, numberOfAxesInRange = 0; |
| 17 | uint16_t timeout; |
||
| 18 | // GyroDefectNick = 0; GyroDefectRoll = 0; GyroDefectYaw = 0; |
||
| 1908 | - | 19 | timeout = setDelay(2000); |
| 1612 | dongfang | 20 | |
| 1821 | - | 21 | for (i = 140; i != 0; i--) { |
| 22 | // If all 3 axis are in range, shorten the remaining number of iterations. |
||
| 23 | if (numberOfAxesInRange == 3 && i > 10) |
||
| 1964 | - | 24 | i = 10; |
| 1821 | - | 25 | numberOfAxesInRange = 0; |
| 26 | |||
| 27 | for (axis = PITCH; axis <= YAW; axis++) { |
||
| 28 | if (axis == YAW) |
||
| 29 | factor = GYRO_SUMMATION_FACTOR_YAW; |
||
| 30 | else |
||
| 31 | factor = GYRO_SUMMATION_FACTOR_PITCHROLL; |
||
| 32 | |||
| 33 | if (rawGyroSum[axis] < 510 * factor) |
||
| 34 | DACValues[axis]--; |
||
| 35 | else if (rawGyroSum[axis] > 515 * factor) |
||
| 36 | DACValues[axis]++; |
||
| 37 | else |
||
| 38 | numberOfAxesInRange++; |
||
| 39 | |||
| 40 | /* Gyro is defective. But do keep DAC within bounds (it's an op amp not a differential amp). */ |
||
| 41 | if (DACValues[axis] < 10) { |
||
| 42 | DACValues[axis] = 10; |
||
| 43 | } else if (DACValues[axis] > 245) { |
||
| 44 | DACValues[axis] = 245; |
||
| 45 | } |
||
| 46 | } |
||
| 47 | |||
| 48 | I2C_Start(TWI_STATE_GYRO_OFFSET_TX); // initiate data transmission |
||
| 49 | |||
| 50 | // Wait for I2C to finish transmission. |
||
| 51 | while (twi_state) { |
||
| 52 | // Did it take too long? |
||
| 1908 | - | 53 | if (checkDelay(timeout)) { |
| 1821 | - | 54 | printf("\r\n DAC or I2C Error! check I2C, 3Vref, DAC, and BL-Ctrl"); |
| 55 | break; |
||
| 56 | } |
||
| 57 | } |
||
| 58 | |||
| 1964 | - | 59 | delay_ms_Mess(i <= 10 ? 10 : 2); |
| 1775 | - | 60 | } |
| 1908 | - | 61 | delay_ms_Mess(70); |
| 1612 | dongfang | 62 | } |
| 63 | |||
| 64 | void gyro_setDefaults(void) { |
||
| 1960 | - | 65 | staticParams.gyroD = 3; |
| 66 | staticParams.driftCompDivider = 1; |
||
| 67 | staticParams.driftCompLimit = 200; |
||
| 68 | staticParams.zerothOrderCorrection = 25; |
||
| 1612 | dongfang | 69 | } |