WebSVN - FlightCtrl - Blame - Rev 2177 - /branches/V0.88n_ACC-HH_HR

Rev	Author	Line No.	Line
1171	hbuss	1	/*#######################################################################################
		2	Decodieren eines RC Summen Signals oder Spektrum Empf�nger-Satellit
		3	#######################################################################################*/
		4
1426	ingob	5	#include "Spektrum.h"
1171	hbuss	6	#include "main.h"
1928	holgerb	7	// Achtung: RECEIVER_SPEKTRUM_DX7EXP oder RECEIVER_SPEKTRUM_DX8EXP wird in der Main.h gesetzt
1506	holgerb	8
2177	-	9	#ifndef WITHSPECTRUM /// MartinW
		10	#warning : "### without SPECTRUM Code ###"
		11	#endif
		12
1320	hbuss	13	unsigned char SpektrumTimer = 0;
1171	hbuss	14
1928	holgerb	15	#if defined (RECEIVER_SPEKTRUM_DX7EXP) \|\| defined (RECEIVER_SPEKTRUM_DX8EXP)
1680	holgerb	16	unsigned char s_excnt = 0; // Counter for Spektrum-Expander
		17	unsigned char s_exparity = 0; // Parity Bit for Spektrum-Expander
		18	signed char s_exdata[11]; // Data for Spektrum-Expander
1506	holgerb	19	#endif
1213	ingob	20	//--------------------------------------------------------------//
		21	//--------------------------------------------------------------//
1743	holgerb	22	/*
1213	ingob	23	void SpektrumBinding(void)
		24	{
		25	unsigned int timerTimeout = SetDelay(10000); // Timeout 10 sec.
		26	unsigned char connected = 0;
		27	unsigned int delaycounter;
1391	killagreg	28
1213	ingob	29	UCSR1B &= ~(1 << RXCIE1); // disable rx-interrupt
		30	UCSR1B &= ~(1<<RXEN1); // disable Uart-Rx
		31	PORTD &= ~(1 << PORTD2); // disable pull-up
1391	killagreg	32
1213	ingob	33	printf("\n\rPlease connect Spektrum receiver for binding NOW...");
1391	killagreg	34
1213	ingob	35	while(!CheckDelay(timerTimeout))
		36	{
		37	if (PIND & (1 << PORTD2)) { timerTimeout = SetDelay(90); connected = 1; break; }
		38	}
1391	killagreg	39
		40	if (connected)
		41	{
		42
		43	printf("ok.\n\r");
1213	ingob	44	DDRD \|= (1 << DDD2); // Rx as output
		45
1680	holgerb	46	while(!CheckDelay(timerTimeout)); // delay after startup of RX
		47	for (delaycounter = 0; delaycounter < 100; delaycounter++) PORTD \|= (1 << PORTD2);
		48	for (delaycounter = 0; delaycounter < 400; delaycounter++) PORTD &= ~(1 << PORTD2);
1391	killagreg	49
1680	holgerb	50	for (delaycounter = 0; delaycounter < 10; delaycounter++) PORTD \|= (1 << PORTD2);
1213	ingob	51	for (delaycounter = 0; delaycounter < 10; delaycounter++) PORTD &= ~(1 << PORTD2);
1680	holgerb	52	for (delaycounter = 0; delaycounter < 400; delaycounter++) PORTD \|= (1 << PORTD2);
		53	for (delaycounter = 0; delaycounter < 400; delaycounter++) PORTD &= ~(1 << PORTD2);
1391	killagreg	54
1680	holgerb	55	for (delaycounter = 0; delaycounter < 10; delaycounter++) PORTD \|= (1 << PORTD2);
1213	ingob	56	for (delaycounter = 0; delaycounter < 10; delaycounter++) PORTD &= ~(1 << PORTD2);
1680	holgerb	57	for (delaycounter = 0; delaycounter < 400; delaycounter++) PORTD \|= (1 << PORTD2);
		58	for (delaycounter = 0; delaycounter < 400; delaycounter++) PORTD &= ~(1 << PORTD2);
1213	ingob	59
1680	holgerb	60	for (delaycounter = 0; delaycounter < 10; delaycounter++) PORTD \|= (1 << PORTD2);
1213	ingob	61	for (delaycounter = 0; delaycounter < 10; delaycounter++) PORTD &= ~(1 << PORTD2);
1680	holgerb	62	for (delaycounter = 0; delaycounter < 400; delaycounter++) PORTD \|= (1 << PORTD2);
1391	killagreg	63
1213	ingob	64	}
1391	killagreg	65	else
		66	{ printf("Timeout.\n\r");
		67
		68
1213	ingob	69	}
1391	killagreg	70
1213	ingob	71	DDRD &= ~(1 << DDD2); // RX as input
1391	killagreg	72	PORTD &= ~(1 << PORTD2);
1213	ingob	73
1424	ingob	74	SpektrumUartInit(); // init Uart again
1213	ingob	75	}
1743	holgerb	76	*/
1171	hbuss	77	//############################################################################
		78	// USART1 initialisation from killagreg
1424	ingob	79	void SpektrumUartInit(void)
1171	hbuss	80	//############################################################################
		81	{
2177	-	82	#ifdef WITHSPECTRUM /// MartinW main.h means no memsave
		83	#warning : "### with left over Spectrum code ###"
		84
1680	holgerb	85	// -- Start of USART1 initialisation for Spekturm seriell-mode
		86	// USART1 Control and Status Register A, B, C and baud rate register
		87	uint8_t sreg = SREG;
1928	holgerb	88
1680	holgerb	89	uint16_t ubrr = (uint16_t) ((uint32_t) SYSCLK/(8 * 115200) - 1);
1928	holgerb	90
1680	holgerb	91	// disable all interrupts before reconfiguration
		92	cli();
		93	// disable RX-Interrupt
		94	UCSR1B &= ~(1 << RXCIE1);
		95	// disable TX-Interrupt
		96	UCSR1B &= ~(1 << TXCIE1);
		97	// disable DRE-Interrupt
		98	UCSR1B &= ~(1 << UDRIE1);
		99	// set direction of RXD1 and TXD1 pins
		100	// set RXD1 (PD2) as an input pin
		101	PORTD \|= (1 << PORTD2);
		102	DDRD &= ~(1 << DDD2);
1431	ingob	103
1680	holgerb	104	// set TXD1 (PD3) as an output pin
		105	PORTD \|= (1 << PORTD3);
		106	DDRD \|= (1 << DDD3);
1928	holgerb	107
1680	holgerb	108	// USART0 Baud Rate Register
		109	// set clock divider
		110	UBRR1H = (uint8_t)(ubrr>>8);
		111	UBRR1L = (uint8_t)ubrr;
		112	// enable double speed operation
		113	UCSR1A \|= (1 << U2X1);
		114	// enable receiver and transmitter
		115	//UCSR1B = (1<<RXEN1)\|(1<<TXEN1);
1391	killagreg	116
1680	holgerb	117	UCSR1B = (1<<RXEN1);
		118	// set asynchronous mode
		119	UCSR1C &= ~(1 << UMSEL11);
		120	UCSR1C &= ~(1 << UMSEL10);
		121	// no parity
		122	UCSR1C &= ~(1 << UPM11);
		123	UCSR1C &= ~(1 << UPM10);
		124	// 1 stop bit
		125	UCSR1C &= ~(1 << USBS1);
		126	// 8-bit
		127	UCSR1B &= ~(1 << UCSZ12);
		128	UCSR1C \|= (1 << UCSZ11);
		129	UCSR1C \|= (1 << UCSZ10);
		130	// flush receive buffer explicit
		131	while(UCSR1A & (1<<RXC1)) UDR1;
		132	// enable RX-interrupts at the end
		133	UCSR1B \|= (1 << RXCIE1);
		134	// -- End of USART1 initialisation
		135	// restore global interrupt flags
1928	holgerb	136
1680	holgerb	137	SREG = sreg;
2177	-	138	#endif
1171	hbuss	139	return;
		140	}
1391	killagreg	141
1171	hbuss	142	// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
		143	// + Copyright (c) Rainer Walther
		144	// + RC-routines from original MK rc.c (c) H&I
		145	// + Useful infos from Walter: http://www.rcgroups.com/forums/showthread.php?t=714299&page=2
		146	// + only for non-profit use
		147	// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
		148	//
		149	// 20080808 rw Modified for Spektrum AR6100 (PPM)
		150	// 20080823 rw Add Spektrum satellite receiver on USART1 (644P only)
		151	// 20081213 rw Add support for Spektrum DS9 Air-Tx-Module (9 channels)
		152	// Replace AR6100-coding with original composit-signal routines
		153	//
		154	// ---
		155	// Entweder Summensignal ODER Spektrum-Receiver anschlie�en. Nicht beides gleichzeitig betreiben!
		156	// Binding is not implemented. Bind with external Receiver.
		157	// Servo output J3, J4, J5 not serviced
		158	//
		159	// Anschu� Spektrum Receiver
1680	holgerb	160	// Orange: 3V von der FC (keinesfalls an 5V anschlie�en!)
		161	// Schwarz: GND
		162	// Grau: RXD1 (Pin 3) auf 10-Pol FC-Stecker
1171	hbuss	163	//
		164	// ---
		165	// Satellite-Reciever connected on USART1:
		166	//
		167	// DX7/DX6i: One data-frame at 115200 baud every 22ms.
		168	// DX7se: One data-frame at 115200 baud every 11ms.
1680	holgerb	169	// byte1: unknown
		170	// byte2: unknown
		171	// byte3: and byte4: channel data (FLT-Mode)
		172	// byte5: and byte6: channel data (Roll)
		173	// byte7: and byte8: channel data (Nick)
		174	// byte9: and byte10: channel data (Gier)
		175	// byte11: and byte12: channel data (Gear Switch)
		176	// byte13: and byte14: channel data (Gas)
		177	// byte15: and byte16: channel data (AUX2)
1171	hbuss	178	//
		179	// DS9 (9 Channel): One data-frame at 115200 baud every 11ms, alternating frame 1/2 for CH1-7 / CH8-9
		180	// 1st Frame:
1680	holgerb	181	// byte1: unknown
		182	// byte2: unknown
		183	// byte3: and byte4: channel data
		184	// byte5: and byte6: channel data
		185	// byte7: and byte8: channel data
		186	// byte9: and byte10: channel data
		187	// byte11: and byte12: channel data
		188	// byte13: and byte14: channel data
		189	// byte15: and byte16: channel data
1171	hbuss	190	// 2nd Frame:
1680	holgerb	191	// byte1: unknown
		192	// byte2: unknown
		193	// byte3: and byte4: channel data
		194	// byte5: and byte6: channel data
		195	// byte7: and byte8: 0xffff
		196	// byte9: and byte10: 0xffff
		197	// byte11: and byte12: 0xffff
		198	// byte13: and byte14: 0xffff
		199	// byte15: and byte16: 0xffff
1171	hbuss	200	//
		201	// Each channel data (16 bit= 2byte, first msb, second lsb) is arranged as:
		202	//
		203	// Bits: F 0 C3 C2 C1 C0 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
		204	//
		205	// 0 means a '0' bit
		206	// F: 1 = indicates beginning of 2nd frame for CH8-9 (DS9 only)
		207	// C3 to C0 is the channel number. 0 to 9 (4 bit, as assigned in the transmitter)
		208	// D9 to D0 is the channel data (10 bit) 0xaa..0x200..0x356 for 100% transmitter-travel
		209	//
		210	// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
		211
1322	hbuss	212	#define MIN_FRAMEGAP 68 // 7ms
		213	#define MAX_BYTEGAP 3 // 310us
1320	hbuss	214
1419	ingob	215
1171	hbuss	216	//############################################################################
1481	holgerb	217	// Wird im UART-Interrupt aufgerufen
1171	hbuss	218	//############################################################################
1419	ingob	219	void SpektrumParser(unsigned char c)
1171	hbuss	220	{
2177	-	221	#ifdef WITHSPECTRUM /// MartinW main.h means no memsave
		222	#warning : "### with left over Spectrum code ###"
		223
1320	hbuss	224	static unsigned char Sync=0, FrameCnt=0, ByteHigh=0, ReSync=1, Frame2=0;
1680	holgerb	225	unsigned int Channel, index = 0;
		226	signed int signal = 0, tmp;
		227	int bCheckDelay;
		228	// c = UDR1; // get data byte
		229	if(ReSync == 1)
		230	{
		231	// wait for beginning of new frame
		232	ReSync = 0;
		233	SpektrumTimer = MIN_FRAMEGAP;
		234	FrameCnt = 0;
		235	Sync = 0;
		236	ByteHigh = 0;
		237	}
1171	hbuss	238	else
1391	killagreg	239	{
1680	holgerb	240	if(!SpektrumTimer) bCheckDelay = 1; else bCheckDelay = 0;//CheckDelay(FrameTimer);
		241	if ( Sync == 0 )
		242	{
		243	if(bCheckDelay)
		244	{
		245	// nach einer Pause von mind. 7ms erstes Sync-Character gefunden
		246	// Zeichen ignorieren, da Bedeutung unbekannt
		247	Sync = 1;
		248	FrameCnt ++;
		249	SpektrumTimer = MAX_BYTEGAP;
		250	}
		251	else
		252	{
		253	// Zeichen kam vor Ablauf der 7ms Sync-Pause
		254	// warten auf erstes Sync-Zeichen
		255	SpektrumTimer = MIN_FRAMEGAP;
		256	FrameCnt = 0;
		257	Sync = 0;
		258	ByteHigh = 0;
		259	}
		260	}
		261	else if((Sync == 1) && !bCheckDelay)
		262	{
		263	// zweites Sync-Character ignorieren, Bedeutung unbekannt
		264	Sync = 2;
		265	FrameCnt ++;
		266	SpektrumTimer = MAX_BYTEGAP;
		267	}
		268	else if((Sync == 2) && !bCheckDelay)
		269	{
		270	SpektrumTimer = MAX_BYTEGAP;
		271	// Datenbyte high
		272	ByteHigh = c;
		273	if (FrameCnt == 2)
		274	{
		275	// is 1st Byte of Channel-data
		276	// Frame 1 with Channel 1-7 comming next
		277	Frame2 = 0;
		278	if(ByteHigh & 0x80)
		279	{
		280	// DS9: Frame 2 with Channel 8-9 comming next
		281	Frame2 = 1;
		282	}
		283	}
		284	Sync = 3;
		285	FrameCnt ++;
		286	}
		287	else if((Sync == 3) && !bCheckDelay)
		288	{
		289	// Datenbyte low
		290	// High-Byte for next channel comes next
		291	SpektrumTimer = MAX_BYTEGAP;
		292	Sync = 2;
		293	FrameCnt ++;
		294	Channel = ((unsigned int)ByteHigh << 8) \| c;
		295	if(EE_Parameter.Receiver == RECEIVER_SPEKTRUM)
		296	{
		297	signal = Channel & 0x3ff;
		298	signal -= 0x200; // Offset, range 0x000..0x3ff?
		299	signal = signal/3; // scaling to fit PPM resolution
		300	index = (ByteHigh >> 2) & 0x0f;
		301	}
		302	else
		303	if(EE_Parameter.Receiver == RECEIVER_SPEKTRUM_HI_RES)
		304	{
		305	signal = Channel & 0x7ff;
		306	signal -= 0x400; // Offset, range 0x000..0x7ff?
		307	signal = signal/6; // scaling to fit PPM resolution
		308	index = (ByteHigh >> 3) & 0x0f;
1928	holgerb	309	}
1680	holgerb	310	else
		311	//if(EE_Parameter.Receiver == RECEIVER_SPEKTRUM_LOW_RES)
		312	{
		313	signal = Channel & 0x3ff;
		314	signal -= 360; // Offset, range 0x000..0x3ff?
		315	signal = signal/2; // scaling to fit PPM resolution
		316	index = (ByteHigh >> 2) & 0x0f;
		317	}
1391	killagreg	318
1680	holgerb	319	index++;
		320	if(index < 13)
		321	{
		322	// Stabiles Signal
1928	holgerb	323	#if defined (RECEIVER_SPEKTRUM_DX7EXP) \|\| defined (RECEIVER_SPEKTRUM_DX8EXP)
		324	if (index == 2) index = 4; // Analog channel reassigment (2 <-> 4) for logical numbering (1,2,3,4)
		325	else if (index == 4) index = 2;
1506	holgerb	326	#endif
2011	holgerb	327	if(abs(signal - PPM_in[index]) < 6)
		328	{
		329	if(EE_Parameter.FailsafeChannel == 0 \|\| PPM_in[EE_Parameter.FailsafeChannel] < 100) // forces Failsafe if the receiver doesn't have 'signal loss' on Failsafe
		330	{
		331	if(SenderOkay < 200) SenderOkay += 10;
		332	else
		333	{
1928	holgerb	334	SenderOkay = 200;
		335	TIMSK1 &= ~_BV(ICIE1); // disable PPM-Input
2011	holgerb	336	}
		337	}
		338	}
1928	holgerb	339	tmp = (3 * (PPM_in[index]) + signal) / 4;
		340	if(tmp > signal+1) tmp--; else
		341	if(tmp < signal-1) tmp++;
		342
		343	#ifdef RECEIVER_SPEKTRUM_DX7EXP
		344	if(index == 6) // FLIGHT-MODE - The channel used for our data uplink
		345	{
		346	if (signal > 100) // SYNC received
		347	{
		348	if (s_exdata[s_excnt] == 125) s_exparity = ~s_exparity; // Bit = 1 -> Re-Invert parity bit
		349	if ((s_excnt == 6 && ((s_exparity != 0 && s_exdata[s_excnt] == -125) \|\| (s_exparity == 0 && s_exdata[s_excnt] == 125))) \|\| (s_excnt == 9 && ((s_exparity == 0 && s_exdata[s_excnt] == -125) \|\| (s_exparity != 0 && s_exdata[s_excnt] == 125)))) // Parity check
		350	{
		351	if (s_exdata[1] == 125 && s_exdata[2] == -125) PPM_in[5] = -125; // Reconstruct tripole Flight-Mode value (CH5)
		352	else if (s_exdata[1] == -125 && s_exdata[2] == -125) PPM_in[5] = 0; // Reconstruct tripole Flight-Mode value (CH5)
		353	else if (s_exdata[1] == -125 && s_exdata[2] == 125) PPM_in[5] = 125; // Reconstruct tripole Flight-Mode value (CH5)
		354	PPM_in[6] = s_exdata[3]; // Elevator (CH6)
		355	PPM_in[11] = s_exdata[4]; // Aileron (CH11)
		356	PPM_in[12] = s_exdata[5]; // Rudder (CH12)
1680	holgerb	357
1928	holgerb	358	if (s_excnt == 9) // New Mode (12 Channels)
		359	{
		360	if (s_exdata[7] == 125) PPM_in[8] += 5; // Hover Pitch UP (CH8)
		361	if (s_exdata[8] == 125) PPM_in[8] -= 5; // Hover Pitch DN (CH8)
		362	if (PPM_in[8] < -125) PPM_in[8] = -125; // Range-Limit
		363	else if (PPM_in[8] > 125) PPM_in[8] = 125; // Range-Limit
		364	PPM_in[10] = s_exdata[6]; // AUX2 (CH10)
		365	}
		366	}
1680	holgerb	367
1928	holgerb	368	s_excnt = 0; // Reset bitcounter
		369	s_exparity = 0; // Reset parity bit
		370	}
1506	holgerb	371
1928	holgerb	372	if (signal < 10) s_exdata[++s_excnt] = -125; // Bit = 0 -> value = -125 (min)
		373	if (s_excnt == 10) s_excnt = 0; // Overflow protection
		374	if (signal < -100)
		375	{
		376	s_exdata[s_excnt] = 125; // Bit = 1 -> value = 125 (max)
		377	s_exparity = ~s_exparity; // Bit = 1 -> Invert parity bit
		378	}
1680	holgerb	379
1928	holgerb	380	}
		381
		382	#elif defined RECEIVER_SPEKTRUM_DX8EXP
		383	if(index == 6) // FLIGHT-MODE - The channel used for our data uplink
		384	{
		385	if (signal > 100) // SYNC received
		386	{
		387	if (s_exdata[s_excnt] == 125) s_exparity = ~s_exparity; // Bit = 1 -> Re-Invert parity bit
		388	if (s_excnt == 9 && ((s_exparity == 0 && s_exdata[s_excnt] == -125) \|\| (s_exparity != 0 && s_exdata[s_excnt] == 125))) // Parity check
		389	{
		390	if (s_exdata[1] == 125 && s_exdata[2] == -125) PPM_in[5] = -125; // Reconstruct tripole Flight-Mode value (CH5)
		391	else if (s_exdata[1] == -125 && s_exdata[2] == -125) PPM_in[5] = 0; // Reconstruct tripole Flight-Mode value (CH5)
		392	else if (s_exdata[1] == -125 && s_exdata[2] == 125) PPM_in[5] = 125; // Reconstruct tripole Flight-Mode value (CH5)
		393
		394	if (s_exdata[3] == 125 && s_exdata[6] == -125) PPM_in[6] = 125; // Reconstruct tripole Elev D/R value (CH6)
		395	else if (s_exdata[3] == -125 && s_exdata[6] == -125) PPM_in[6] = 0; // Reconstruct tripole Elev D/R value (CH6)
		396	else if (s_exdata[3] == -125 && s_exdata[6] == 125) PPM_in[6] = -125; // Reconstruct tripole Elev D/R value (CH6)
		397
		398
		399	if (s_exdata[7] == 125 && s_exdata[8] == -125) PPM_in[9] = -125; // Reconstruct tripole AIL D/R value (CH9)
		400	else if (s_exdata[7] == -125 && s_exdata[8] == -125) PPM_in[9] = 0; // Reconstruct tripole AIL D/R value (CH9)
		401	else if (s_exdata[7] == -125 && s_exdata[8] == 125) PPM_in[9] = 125; // Reconstruct tripole AIL D/R value (CH9)
		402
		403	PPM_in[10] = s_exdata[5]; // Gear (CH10)
		404	PPM_in[12] = s_exdata[4]; // Mix (CH12)
		405	}
		406
		407	s_excnt = 0; // Reset bitcounter
		408	s_exparity = 0; // Reset parity bit
		409	}
		410
		411	if (signal < 10) s_exdata[++s_excnt] = -125; // Bit = 0 -> value = -125 (min)
		412	if (s_excnt == 10) s_excnt = 0; // Overflow protection
		413	if (signal < -100)
		414	{
		415	s_exdata[s_excnt] = 125; // Bit = 1 -> value = 125 (max)
		416	s_exparity = ~s_exparity; // Bit = 1 -> Invert parity bit
		417	}
		418
		419	}
1506	holgerb	420	#endif
1928	holgerb	421	if(SenderOkay >= 180) PPM_diff[index] = ((tmp - PPM_in[index]) / 3) * 3;
		422	else PPM_diff[index] = 0;
1506	holgerb	423
1928	holgerb	424	#ifdef RECEIVER_SPEKTRUM_DX7EXP
		425	if (index < 5 ) PPM_in[index] = tmp; // Update normal potis (CH1-4)
		426	else if (index == 5) PPM_in[7] = signal; // Gear (CH7)
		427	else if (index == 7) PPM_in[9] = signal; // Hover Throttle (CH9)
		428	#elif defined RECEIVER_SPEKTRUM_DX8EXP
		429	if (index < 5 ) PPM_in[index] = tmp; // Update normal potis (CH1-4)
		430	else if (index == 7) PPM_in[7] = signal; // R Trim (CH7)
		431	else if (index == 5) PPM_in[8] = signal; // AUX2 (CH8)
		432	else if (index == 8) PPM_in[11] = signal; // AUX3 (CH11)
1506	holgerb	433	#else
1928	holgerb	434	PPM_in[index] = tmp;
1506	holgerb	435	#endif
1928	holgerb	436	}
1506	holgerb	437	else if(index > 17) ReSync = 1; // hier stimmt was nicht: neu synchronisieren
1680	holgerb	438	}
		439	else
		440	{
		441	// hier stimmt was nicht: neu synchronisieren
		442	ReSync = 1;
		443	FrameCnt = 0;
		444	Frame2 = 0;
		445	// new frame next, nach fruehestens 7ms erwartet
		446	SpektrumTimer = MIN_FRAMEGAP;
		447	}
1391	killagreg	448
1680	holgerb	449	// 16 Bytes eingetroffen -> Komplett
		450	if(FrameCnt >= 16)
		451	{
		452	// Frame complete
		453	if(Frame2 == 0)
		454	{
		455	// Null bedeutet: Neue Daten
		456	// nur beim ersten Frame (CH 0-7) setzen
		457	if(!ReSync) NewPpmData = 0;
		458	}
		459	FrameCnt = 0;
		460	Frame2 = 0;
		461	Sync = 0;
		462	SpektrumTimer = MIN_FRAMEGAP;
		463	}
1171	hbuss	464	}
2177	-	465	#endif
1391	killagreg	466	}
1928	holgerb	467

Subversion Repositories FlightCtrl

(root)/branches/V0.88n_ACC-HH_HR_MartinR/Spektrum.c - Rev 2177