Subversion Repositories FlightCtrl

Rev

Details | Last modification | View Log | RSS feed

Rev Author Line No. Line
1 ingob 1
/*#######################################################################################
685 killagreg 2
Decodieren eines RC Summen Signals
1 ingob 3
#######################################################################################*/
4
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
5
// + Copyright (c) 04.2007 Holger Buss
6
// + only for non-profit use
7
// + www.MikroKopter.com
8
// + see the File "License.txt" for further Informations
9
// ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
10
 
687 killagreg 11
#include <stdlib.h>
685 killagreg 12
#include <avr/io.h>
13
#include <avr/interrupt.h>
14
 
1 ingob 15
#include "rc.h"
732 killagreg 16
#include "main.h"
1 ingob 17
 
687 killagreg 18
volatile int16_t PPM_in[11];
688 killagreg 19
volatile int16_t PPM_diff[11];
687 killagreg 20
volatile uint8_t NewPpmData = 1;
688 killagreg 21
volatile uint8_t SenderOkay = 0;
1 ingob 22
 
687 killagreg 23
/***************************************************************/
688 killagreg 24
/*  16bit timer 1 is used to decode the PPM-Signal            */
687 killagreg 25
/***************************************************************/
712 killagreg 26
void RC_Init (void)
1 ingob 27
{
688 killagreg 28
        uint8_t sreg = SREG;
1 ingob 29
 
688 killagreg 30
        // disable all interrupts before reconfiguration
31
        cli();
685 killagreg 32
 
688 killagreg 33
        // PPM-signal is connected to the Input Capture Pin (PD6) of timer 1
34
        DDRD &= ~(1<<DDD6);
35
        PORTD |= (1<<PORTD6);
36
 
689 killagreg 37
        // Channel 5,6,7 is decoded to servo signals at pin PD5 (J3), PD4(J4), PD3(J5)
38
        // set as output
39
        DDRD |= (1<<DDD5)|(1<<DDD4)|(1<<DDD3);
40
        // low level
41
        PORTD &= ~((1<<PORTD5)|(1<<PORTD4)|(1<<PORTD3));
42
 
732 killagreg 43
        // PD3 can't be used in FC 1.1 if 2nd UART is activated
44
        // becouse TXD1 is at that port
45
        if(BoardRelease == 10)
46
        {
47
                DDRD |= (1<<PORTD3);
48
                PORTD &= ~(1<<PORTD3);
49
        }
50
 
688 killagreg 51
        // Timer/Counter1 Control Register A, B, C
52
 
53
        // Normal Mode (bits: WGM13=0, WGM12=0, WGM11=0, WGM10=0)
54
        // Compare output pin A & B is disabled (bits: COM1A1=0, COM1A0=0, COM1B1=0, COM1B0=0)
55
        // Set clock source to SYSCLK/64 (bit: CS12=0, CS11=1, CS10=1)
56
        // Enable input capture noise cancler (bit: ICNC1=1)
57
        // Trigger on positive edge of the input capture pin (bit: ICES1=1),
58
        // Therefore the counter incremets at a clock of 20 MHz/64 = 312.5 kHz or 3.2µs
59
    // The longest period is 0xFFFF / 312.5 kHz = 0.209712 s.
60
        TCCR1A &= ~((1<<COM1A1)|(1<<COM1A0)|(1<<COM1B1)|(1<<COM1B0)|(1<<WGM11)|(1<<WGM10));
61
        TCCR1B &= ~((1<<WGM13)|(1<<WGM12)|(1<<CS12));
62
        TCCR1B |= (1<<CS11)|(1<<CS10)|(1<<ICES1)|(1<<ICNC1);
63
        TCCR1C &= ~((1<<FOC1A)|(1<<FOC1B));
64
 
65
        // Timer/Counter1 Interrupt Mask Register
66
 
67
        // Enable Input Capture Interrupt (bit: ICIE1=1)
68
        // Disable Output Compare A & B Match Interrupts (bit: OCIE1B=0, OICIE1A=0)
69
        // Disable Overflow Interrupt (bit: TOIE1=0)
70
        TIMSK1 &= ~((1<<OCIE1B)|(1<<OCIE1A)|(1<<TOIE1));
71
    TIMSK1 |= (1<<ICIE1);
72
 
73
    SREG = sreg;
1 ingob 74
}
75
 
76
 
688 killagreg 77
/********************************************************************/
78
/*         Every time a positive edge is detected at PD6            */
79
/********************************************************************/
80
/*
81
The PPM-Frame length is 22.5 ms.
82
Channel high pulse width range is 0.7 ms to 1.7 ms completed by an 0.3 ms low pulse.
83
The mininimum time delay of two events coding a channel is ( 0.7 + 0.3) ms = 1 ms.
84
The maximum time delay of two events coding a chanel is ( 1.7 + 0.3) ms = 2 ms.
85
The minimum duration of all channels at minimum value is  8 * 1 ms = 8 ms.
86
The maximum duration of all channels at maximum value is  8 * 2 ms = 16 ms.
87
The remaining time of (22.5 - 8 ms) ms = 14.5 ms  to (22.5 - 16 ms) ms = 6.5 ms is
88
the syncronization gap.
89
*/
90
ISR(TIMER1_CAPT_vect) // typical rate of 1 ms to 2 ms
1 ingob 91
{
688 killagreg 92
        static uint16_t oldICR1 = 0;
93
    int16_t signal = 0, tmp;
94
        static int16_t index;
685 killagreg 95
 
688 killagreg 96
        // 16bit Input Capture Register ICR1 contains the timer value TCNT1
97
        // at the time the edge was detected
685 killagreg 98
 
688 killagreg 99
        // calculate the time delay to the previous event time which is stored in oldICR1
100
        signal = (uint16_t) ICR1 - oldICR1;
101
        oldICR1 = ICR1;
102
 
103
 
104
    //sync gap? (3.52 ms < signal < 25.6 ms)
685 killagreg 105
        if((signal > 1100) && (signal < 8000))
688 killagreg 106
        {
107
                // if a sync gap happens and there where at least 4 channels decoded before
108
                // then the NewPpmData flag is reset indicating valid data in the PPM_in[] array.
109
                if(index >= 4)  NewPpmData = 0;  // Null means NewData
110
                // synchronize channel index
111
                index = 1;
112
        }
113
        else // within the PPM frame
1 ingob 114
        {
688 killagreg 115
        if(index < 10) // channel limit is 9 because of the frame length of 22.5 ms
1 ingob 116
        {
688 killagreg 117
                        // check for valid signal length (0.8 ms < signal < 2.1984 ms)
711 killagreg 118
                        // signal range is from 1.0ms/3.2us = 312 to 2.0ms/3.2us = 625
688 killagreg 119
            if((signal > 250) && (signal < 687))
1 ingob 120
            {
711 killagreg 121
                                // shift signal to zero symmetric range  -154 to 159
688 killagreg 122
                signal -= 466; // offset of 1.4912 ms ??? (469 * 3.2µs = 1.5008 ms)
123
                // check for stable signal
124
                // the deviation of the current signal level from the average must be less than 6 (aprox. 1%)
125
                if(abs(signal - PPM_in[index]) < 6)
685 killagreg 126
                {
688 killagreg 127
                                        // a good signal condition increases SenderOkay by 10
711 killagreg 128
                                        // SignalOkay is decremented every 2 ms in main.c
129
                                        // this variable is a level for the average rate of a noiseless rc signal
688 killagreg 130
                                        if(SenderOkay < 200) SenderOkay += 10;
131
                                }
132
                                // calculate exponential history for signal
685 killagreg 133
                tmp = (3 * (PPM_in[index]) + signal) / 4;
604 hbuss 134
                if(tmp > signal+1) tmp--; else
685 killagreg 135
                if(tmp < signal-1) tmp++;
688 killagreg 136
                // calculate signal difference on good signal level
137
                if(SenderOkay >= 195)  PPM_diff[index] = ((tmp - PPM_in[index]) / 3) * 3; // cut off lower 3 bit for nois reduction
604 hbuss 138
                else PPM_diff[index] = 0;
688 killagreg 139
                PPM_in[index] = tmp; // update channel value
140
            }
141
            index++; // next channel
689 killagreg 142
            // demux sum signal for channels 5 to 7 to J3, J4, J5
143
                if(index == 5) PORTD |= (1<<PORTD5); else PORTD &= ~(1<<PORTD5);
144
                if(index == 6) PORTD |= (1<<PORTD4); else PORTD &= ~(1<<PORTD4);
732 killagreg 145
                if(BoardRelease == 10)
146
                {
147
                                if(index == 7) PORTD |= (1<<PORTD3); else PORTD &= ~(1<<PORTD3);
148
                }
1 ingob 149
        }
150
        }
151
}
152
 
153
 
154
 
155
 
156